The Multiplus-II 48/5000/70-50 GX is a high-end device combination from Victron Energy (MPN PMP482506000) that combines classic Multiplus components with an external current sensor and integrated anti-islanding function. This extends the PowerControl and PowerAssist functions to 50 A and extends the potential range of use to ESS applications. The inverter module delivers a full 5000 W with a non-linear load and 4000 W with a linear continuous load. The 48 V battery charger is also very well proportioned with 70 A charging power and is supplemented by a 50 A transfer switch, which can be used to switch back and forth between the AC connections at lightning speed. Compared to the other devices in the series, the GX variants have an integrated GX display with numerous other connection options.Important features of the Multiplus-II 48/5000/70-50 GXIntegrated GX control unit with various communication connectionsPowerControl and PowerAssist to increase mains or generator outputbuilt-in anti-islanding function and connection option for external current sensor (optional)can be used as a backup device in grid-connected systems for power supply in the event of grid failurescan be used in various ESS (Energy Storage System) applicationsideally suited for professional seafaring, yachts, vehicles and land-based, off-grid applicationsVE.Bus interface for parallel and three-phase operation, remote monitoring and system integrationpractically unlimited power thanks to parallel and three-phase operationcan be configured on site or remotely using VEConfigure software* Technical features5000W power with non-linear load 4000 W continuous load and 9000 W peak powerfor 48 V battery voltage, 50 A transfer switch and 70 A battery chargerOutput voltage: 230 VAC, frequency: 50 Hzmax. efficiency is 95%, protection class IP22 Always enough power thanks to PowerControl and PowerAssistA maximum mains or generator current can be set on the MultiPlus-II 48/5000/70-50 GX. The MultiPlus-II then takes account of other connected AC consumers and only uses the power that is still "left over" to charge the battery. This prevents the generator or mains connection from being overloaded (PowerControl function). The PowerAssist function adds a new dimension to the PowerControl principle. Load peaks often only occur for a limited period of time. In such cases, the MultiPlus-II immediately compensates for insufficient generator, shore power or mains power with energy from the battery. If the load is reduced, i.e. consumers are switched off, the available energy can then be used to recharge the batteries.Solar power: alternating current even in the event of a mains failureThe device can be used with both off-grid and grid-connected PV systems as well as other alternative energy systems. It can be used with both solar charge controllers and grid-connected inverters.Maximum flexibility thanks to two AC outputsThe main output ensures uninterrupted operation. In the event of a mains failure or an interruption in the shore/generator current, the MultiPlus-II takes over the supply to the connected loads. The switchover takes place so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic devices is guaranteed. The second output only supplies power when alternating current is available at the input of the MultiPlus-II. Consumers that must not discharge the battery, such as a water heater, can be connected to this output.Scope of the integrated GX deviceA VE.Can interface This can be used to connect VE.Can devices from Victron (e.g. VE.Can MPPT). The connection can also be reconfigured via the remote console for use with a compatible CAN bus Li-ion battery.1xUSB connection1x Ethernet connection1x VE.Direct connectionMany options for system expansionThe settings can be changed within a few minutes using the VEConfigure software (a computer or laptop and an MK3 USB interface are required) and several monitoring and control options are available: Color Control GX, Venus GX, Octo GX, CANvu GX, laptop, computer, Bluetooth (with the optional VE.Bus Smart Dongle), battery monitor, Digital Multi control panel.Remote configuration and monitoringInstall a Color Control GX or other GX products to connect to the Internet. The operating data can be stored and viewed free of charge on our VRM (Victron Remote Management) website. If systems are connected to the Internet, they can be accessed remotely and settings can be changed.Scope of delivery:1x Victron PMP482506000 Multiplus-II 48/5000/70-50 GX 230V1x operating instructions

The Multiplus-II 48/5000/70-50 GX is a high-end device combination from Victron Energy (MPN PMP482506000) that combines classic Multiplus components with an external current sensor and integrated anti-islanding function. This extends the PowerControl and PowerAssist functions to 50 A and extends the potential range of use to ESS applications. The inverter module delivers a full 5000 W with a non-linear load and 4000 W with a linear continuous load. The 48 V battery charger is also very well proportioned with 70 A charging power and is supplemented by a 50 A transfer switch, which can be used to switch back and forth between the AC connections at lightning speed. Compared to the other devices in the series, the GX variants have an integrated GX display with numerous other connection options.Important features of the Multiplus-II 48/5000/70-50 GXIntegrated GX control unit with various communication connectionsPowerControl and PowerAssist to increase mains or generator outputbuilt-in anti-islanding function and connection option for external current sensor (optional)can be used as a backup device in grid-connected systems for power supply in the event of grid failurescan be used in various ESS (Energy Storage System) applicationsideally suited for professional seafaring, yachts, vehicles and land-based, off-grid applicationsVE.Bus interface for parallel and three-phase operation, remote monitoring and system integrationpractically unlimited power thanks to parallel and three-phase operationcan be configured on site or remotely using VEConfigure software* Technical features5000W power with non-linear load 4000 W continuous load and 9000 W peak powerfor 48 V battery voltage, 50 A transfer switch and 70 A battery chargerOutput voltage: 230 VAC, frequency: 50 Hzmax. efficiency is 95%, protection class IP22 Always enough power thanks to PowerControl and PowerAssistA maximum mains or generator current can be set on the MultiPlus-II 48/5000/70-50 GX. The MultiPlus-II then takes account of other connected AC consumers and only uses the power that is still "left over" to charge the battery. This prevents the generator or mains connection from being overloaded (PowerControl function). The PowerAssist function adds a new dimension to the PowerControl principle. Load peaks often only occur for a limited period of time. In such cases, the MultiPlus-II immediately compensates for insufficient generator, shore power or mains power with energy from the battery. If the load is reduced, i.e. consumers are switched off, the available energy can then be used to recharge the batteries.Solar power: alternating current even in the event of a mains failureThe device can be used with both off-grid and grid-connected PV systems as well as other alternative energy systems. It can be used with both solar charge controllers and grid-connected inverters.Maximum flexibility thanks to two AC outputsThe main output ensures uninterrupted operation. In the event of a mains failure or an interruption in the shore/generator current, the MultiPlus-II takes over the supply to the connected loads. The switchover takes place so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic devices is guaranteed. The second output only supplies power when alternating current is available at the input of the MultiPlus-II. Consumers that must not discharge the battery, such as a water heater, can be connected to this output.Scope of the integrated GX deviceA VE.Can interface This can be used to connect VE.Can devices from Victron (e.g. VE.Can MPPT). The connection can also be reconfigured via the remote console for use with a compatible CAN bus Li-ion battery.1xUSB connection1x Ethernet connection1x VE.Direct connectionMany options for system expansionThe settings can be changed within a few minutes using the VEConfigure software (a computer or laptop and an MK3 USB interface are required) and several monitoring and control options are available: Color Control GX, Venus GX, Octo GX, CANvu GX, laptop, computer, Bluetooth (with the optional VE.Bus Smart Dongle), battery monitor, Digital Multi control panel.Remote configuration and monitoringInstall a Color Control GX or other GX products to connect to the Internet. The operating data can be stored and viewed free of charge on our VRM (Victron Remote Management) website. If systems are connected to the Internet, they can be accessed remotely and settings can be changed.Scope of delivery:1x Victron PMP482506000 Multiplus-II 48/5000/70-50 GX 230V1x operating instructions

The new MultiPlus 12/1200/50-16 (Victron Energy, PMP122120000) is the successor to the Multiplus Compact 12/1200 and is a modern device combination consisting of a powerful inverter with pure sine wave, an advanced 50A battery charger that uses adaptive charging technology and a 16A high-speed AC voltage transfer switch.In the event of a mains fault or if the shore power or on-board generator is interrupted, the Multi's inverter is automatically switched on and takes over the supply to the connected loads. The switchover happens so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic devices is guaranteed.Key features of the MultiPlus 12/1200/50-16 Cont. Output power at 25°C: 1200WVictron Energy MPN: PMP122120000for 12V system voltageintegrated 50A mains charger for your batteriesintegrated 16A mains transfer switchUPS operation possibleExtensive range of accessories availableCan be used in numerous areas of application, whether on land or mobileProven reliability Complete bridging with an additional toroidal transformer topology has proven itself over many years. The inverter is short-circuit-proof and protected against overheating (whether caused by overload or ambient temperature).PowerControl - (Multiplus 800VA 1200VA only). The maximum mains or generator current to be drawn can be set using the Multi Control remote control panel. The MultiPlus then takes account of other connected AC consumers and only uses the current that is still “left over” for charging. This prevents the generator or shore power connection from being overloaded.PowerAssist - (Multiplus 800VA 1200VA only) Load peaks often only occur for a limited period of time. In such cases, the MultiPlus ensures that insufficient shore power or generator output is immediately compensated for by energy from the battery. If the load is reduced, i.e. consumers are switched off, the available energy can then be used to recharge the batteries.High switch-on power This is required to switch on loads with high inrush currents, such as voltage converters for LED lamps, halogen lamps or power tools.Search mode If the search mode is set to 'on', the power consumption of the inverter is reduced by approximately 70% in no-load operation. In this mode, when operated in inverter mode, the Multi switches off at zero load or at low load and switches on again every two seconds for a short period. If the output current exceeds a set limit value, the inverter resumes operation. If this is not the case, the inverter switches off again.Programmable relay In the default setting, the multifunction relay acts as an alarm relay, i.e. it switches the device off in the event of faults (device gets too hot, ripple voltage at the input too high, battery voltage too low).Scope of delivery:Victron Energy PMP122120000, MultiPlus 12/1200/50-16

The Multiplus 12/2000/80-32 from Victron (MPN PMP122200000) is a device combination of 12V 2000W sine wave inverter and battery charger. The permanently integrated battery charger delivers an impressive 80A, which means that even large batteries can be fully charged quickly if shore/grid power is available. The 12V sine wave voltage converter built into the Multiplus converts your current from the battery into 230V alternating current. Thanks to the true sine wave, the power quality is also perfect for sensitive electronic devices. In addition to the two integrated device types, a lightning-fast 32A transfer switch is also installed, which can be used to implement numerous grid-connected solutions. The MultiPlus has a VE.Bus port for system integration, which enables virtually limitless networking.Comprehensive and flexible useAs it has a lightning-fast 32A transfer switch in addition to the inverter and charger, it is an ideal inverter for motorhomes, boats or yachts and for grid-connected uninterruptible power supplies in the event of grid fluctuations or power failures. Also for use in grid-connected self-consumption systems that only draw power from the supplier when the battery power is no longer sufficient or as a UPS solution in which the Multiplus steps in if the power from the grid operator suddenly fails and thus ensures an uninterruptible power supply.Key performance features of the Multiplus 12/2000/80-321600W continuous power and 3500W peak power, for 12V battery voltageDevice combination of inverter with transfer switch and 80A battery chargersupplies the purest 230V sine wave voltage and a clean 50Hz frequencyVE.Bus communication port provides extensive networking, system integration, configuration and control options for Victron Multiplus devicessupports three-phase operation (3 identical units of the same model required)Multiplus devices can be connected in parallel, up to 6 devices can be connected in parallel, significantly increasing system performance if requiredPowerControl function enables working with limited generator power as well as limited shore or mains powerPowerAssist function enables “power boost” of generators and shore connection support if requiredCan be used as a UPS solution for uninterruptible power supply thanks to the integrated transfer switchcan be used for grid-connected self-consumption systems that only draw power from the grid operator when the battery capacity is no longer sufficient or other programmable events have occurredCompatible with numerous Victron control and display panelsMassive power expansion possibleIn addition to the parallel connection, three units of the same model can be configured for a three-phase output. But that's not all: up to six sets of three units can be connected in parallel to achieve a huge charging capacityPowerControl - working with limited generator power, limited shore or mains powerThe MultiPlus is a very powerful battery charger. It therefore draws a lot of power from the generator or shore power supply. The maximum mains or generator current to be drawn can be set using the Multi Control remote control panel. The MultiPlus then takes other connected AC consumers into account and only uses the power that is still “left over” for charging. This prevents the generator or shore power connection from being overloaded.PowerAssist - “power boost” for generators and shore power supportThis function adds a new dimension to the PowerControl principle. It enables the MultiPlus to support alternative sources that are too weak. Load peaks often only occur for a limited period of time. In such cases, the MultiPlus ensures that insufficient shore power or generator output is immediately compensated for by energy from the battery.BackUp system: alternating current even in the event of a power failureThe MultiPlus can be used with both off-grid and grid-connected PV systems as well as other alternative energy systems. Software is available to detect a grid failure.Simple system configurationIf settings need to be changed on a single device, this can be done in a matter of minutes using a DIP switch setting procedure.Parallel and three-phase systems can be configured using the VE.Bus Quick Configure and VE.Bus System Configurator software.Monitoring options and on-site controlSeveral options are available: Battery monitor, Multi Control Panel, Ve.Net Blue Power Panel, Color Control Panel, smartphone or tablet (Bluetooth Smart), laptop or computer (USB or RS232).Remote monitoring and controlVictron Ethernet Remote, Victron Global Remote and the Color Control Panel enable remote maintenance and remote monitoring of the MultiPlus. System data can also be saved and viewed free of charge on the VRM (Victron Remote Management) website.Remote configurationIf systems with a Color Control Panel are connected to the Ethernet, they can be accessed and settings can be changed remotely.Scope of delivery:1x Victron PMP122200000 Multiplus 12/2000/80-32 device combination consisting of 12V 2000W sine wave converter + 12V 80A battery charger + 32A transfer switch1x operating instructions

The Multiplus-II 48/3000/35-32 GX is a high-end device combination from Victron Energy (MPN PMP482306000) that combines classic Multiplus components with an external current sensor and integrated anti-islanding function. This extends the PowerControl and PowerAssist functions to 50 A and extends the potential range of use to ESS applications. The inverter module delivers a full 3000 W with a non-linear load and 2400 W with a linear continuous load. The 48 V battery charger is also very well proportioned with 35 A charging power and is supplemented by a 32 A transfer switch, which can be used to switch back and forth between the AC connections at lightning speed. Compared to the other devices in the series, the GX variants have an integrated GX display with numerous other connection options.Important features of the Multiplus-II 48/3000/35-32 GXIntegrated GX control unit with various communication connectionsPowerControl and PowerAssist to increase mains or generator outputbuilt-in anti-islanding function and connection option for external current sensor (optional)can be used as a backup device in grid-connected systems for power supply in the event of grid failurescan be used in various ESS (Energy Storage System) applicationsideally suited for professional seafaring, yachts, vehicles and land-based, off-grid applicationsVE.Bus interface for parallel and three-phase operation, remote monitoring and system integrationpractically unlimited power thanks to parallel and three-phase operationcan be configured on site or remotely using VEConfigure software*Technical features3000W power with non-linear load 2400 W continuous load and 6000 W peak powerfor 48 V battery voltage, 32 A transfer switch and 35 A battery chargerOutput voltage: 230 VAC, frequency: 50 HzMax. efficiency is 95%, protection class IP22Always enough power thanks to PowerControl and PowerAssistA maximum mains or generator current can be set on the MultiPlus-II 48/3000/35-32 GX. The MultiPlus-II then takes account of other connected AC consumers and only uses the power that is still “left over” to charge the battery. This prevents the generator or mains connection from being overloaded (PowerControl function). The PowerAssist function adds a new dimension to the PowerControl principle. Load peaks often only occur for a limited period of time. In such cases, the MultiPlus-II immediately compensates for insufficient generator, shore power or mains power with energy from the battery. If the load is reduced, i.e. consumers are switched off, the available energy can then be used to recharge the batteries.Solar power: alternating current even in the event of a mains failureThe device can be used with both off-grid and grid-connected PV systems as well as other alternative energy systems. It can be used with both solar charge controllers and grid-connected inverters.Maximum flexibility thanks to two AC outputsThe main output ensures uninterrupted operation. In the event of a mains failure or an interruption in the shore/generator current, the MultiPlus-II takes over the supply to the connected loads. The switchover takes place so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic devices is guaranteed. The second output only supplies power when alternating current is available at the input of the MultiPlus-II. Consumers that must not discharge the battery, such as a water heater, can be connected to this output.Scope of the integrated GX deviceA VE.Can interface This can be used to connect VE.Can devices from Victron (e.g. VE.Can MPPT). The connection can also be reconfigured via the remote console for use with a compatible CAN bus Li-ion battery.1xUSB connection1x Ethernet connection1x VE.Direct connectionMany options for system expansionThe settings can be changed within a few minutes using the VEConfigure software (a computer or laptop and an MK3 USB interface are required) and several monitoring and control options are available: Color Control GX, Venus GX, Octo GX, CANvu GX, laptop, computer, Bluetooth (with the optional VE.Bus Smart Dongle), battery monitor, Digital Multi control panel.Remote configuration and monitoringInstall a Color Control GX or other GX products to connect to the Internet. The operating data can be stored and viewed free of charge on our VRM (Victron Remote Management) website. If systems are connected to the Internet, they can be accessed remotely and settings can be changed.Scope of delivery:1x Victron PMP482306000 Multiplus-II 48/3000/35-32 GX 230 V1x operating instructions

Der Multiplus C 24/1200/25 von Victron (MPN CMP241220000) ist eine Gerätekombination aus 24V 1000W Sinus Wechselrichter und Batterie-Ladegerät.  Das fest integrierte Batterieladegerät leistet beachtliche 25A womit auch große Batterien schnell voll geladen werden können wenn Land-/Netzstrom zur Verfügung steht. Der im Multiplus verbaute 24V Sinus Spannungswandler wandelt Ihren Strom aus der Batterie in 230V Wechselstrom um. Dank der echten Sinuswelle ist die Stromqualität auch für empfindliche elektronische Geräte perfekt geeignet. Umfassend und flexibel einsetzbar Da er neben Wechselrichter und Ladegerät auch noch über einen blitzschnellen 16A Transferschalter verfügt, ist er ein idealer Wechselrichter für die Bereiche Wohnmobil, Boot oder Yacht und den netzgekoppelten Bereich der unterbrechungsfreien Stromversorgung im Falle von Netzschwankungen oder Stromausfällen. Auch für den Einsatz in netzgekoppelten Eigenverbrauchsanlagen, die nur Strom vom Versorger ziehen, wenn der Batteriestrom nicht mehr ausreicht oder als USV Lösung, in der die Multiplus einspringen, wenn der Strom vom Netzbetreiber plötzlich ausfällt und so für eine unterbrechungsfreie Stromversorgung sorgen. Wesentliche Leistungsmerkmale des Multiplus C 24/1200/25 1000W Dauerleistung und 2400W Spitzenleistung, für 24V BatteriespannungGerätekombination aus Wechselrichter mit Transfer-Switch und 25A Batterieladegerätliefert reinste 230V Sinusspannung und eine saubere 50Hz FrequenzVE.Bus Kommunikationsport sorgt für umfangreiche Möglichkeiten der Vernetzung, Systemintegration, Konfiguration und Kontrolle der Multiplus Geräte von Victron.unterstütz den Drei-Phasen-Betrieb (3 gleiche Einheiten desselben Models benötigt)Multiplus Geräte sind parallelschaltfähig, bis zu 6 Geräte lassen sich parallel verbinden und die Systemleistung dadurch im Bedarfsfall deutlich steigern2 Wechselstromausgänge ab Multiplus 3000 und größer. An dem zweiten Ausgang können dann zum Beispiel Geräte angeschlossen werden, die nur laufen sollen, wenn Netzstrom verfügbar istPowerControl Funktion ermöglicht das Arbeiten mit begrenzter Generatorleistung so wie eingeschränktem Land- oder NetzstromPowerAssist Funktion ermöglicht  „Leistungssteigerung“ von Generatoren und Landanschlussunterstützung im Bedarfsfallals USV Lösung zur unterbrechungsfreien Stromversorgung einsetzbarfür netzgekoppelte Eigenverbrauchsanlagen einsetzbar, die nur dann Strom vom Netzbetreiber ziehen, wenn die Batteriekapazität nicht mehr ausreicht oder andere programmierbare Ereignisse stattgefunden habenkompatibel mit zahlreichen Victron Steuer- und AnzeigepanelsDrei Phasenbetriebe mit baugleichen MultiPlus Wechselrichtern möglich massiver Leistungsausbau möglich Abgesehen von dem parallelen Anschluss, können auch drei Einheiten desselben Modells für einen Drei-Phasen-Ausgang konfiguriert werden. Damit jedoch nicht genug: Bis zu sechs Sets mit drei Einheiten können parallel geschaltet werden, um eine riesige 75 kW / 90 kVA Wechselrichter- und u¨ber 2.000 A Ladekapazita¨t zu erzielen (mit der 5000er-Version gerechnet) PowerControl – Arbeiten mit begrenzter Generatorleistung, eingeschränktem Land- oder Netzstrom Der MultiPlus ist ein sehr leistungsstarkes Batterieladegerät. Daher nimmt er vom Generator bzw. der Landstromversorgung viel Strom auf (fast 10A pro 5kVA Multi bei 230 VAC). Mit dem Fernbedienungspaneel Multi Control kann der maximal zu entnehmende Netz- bzw. Generatorstrom eingestellt werden. Der MultiPlus nimmt dann Rücksicht auf weitere angeschlossene Wechselstromverbraucher und nutzt zum Laden nur den Strom, der noch „übrig“ ist. So wird verhindert, dass der Generator- oder der Landstromanschluss überlastet wird. PowerAssist – „Leistungssteigerung“ von Generatoren und Landanschlussunterstu¨tzung Mit dieser Funktion erhält das PowerControl-Prinzip eine neue Dimension. Sie ermöglicht, dass der MultiPlus zu schwach ausgelegte alternative Quellen stützt. Lastspitzen treten häufig nur für einen begrenzten Zeitraum auf. In einem solchen Fall stellt der MultiPlus sicher, dass eine zu schwache Landstrom- bzw. Generatorleistung sofort durch Energie aus der Batterie kompensiert wird. BackUp-System: Wechselstrom auch bei Netzausfall Der Multiplus kann sowohl bei nicht netzgekoppelten sowie bei netzgekoppelten PV-Anlagen als auch bei anderen alternativen Energiesystemen eingesetzt werden. Es ist eine Software zur Erkennung eines Netzausfalls verfügbar. Einfache Systemkonfiguration Wenn Einstellungen an einem Einzelgerät verändert werden müssen, kann dies innerhalb von wenigen Minuten mithilfe eines DIP-Schalter-Einstellungsverfahrens erfolgen. Parallel geschaltete und Drei-Phasen-Systeme können mit der VE.Bus Quick Configure- und VE.Bus System Configurator Software konfiguriert werden. Überwachungsoptionen und Steuerung vor Ort Es stehen mehrere Optionen zur Verfügung: Batteriewächter, Multi Control Paneel, Ve.Net Blue Power Paneel, Color Control Paneel, Smartphone oder Tablet (Bluetooth Smart), Laptop oder Computer (USB oder RS232). Überwachung und Steuerung aus der Ferne Victron Ethernet Remote, Victron Global Remote und das Color Control Panel ermöglichen Fernwartung und Fernüberwachung des MultiPlus.  Zudem lassen sich die Systemdaten auf der VRM (Victron Remote Management) Website kostenlos speichern und einsehen. Konfigurierung aus der Ferne Sind Systeme mit einem Color Control Paneel an das Ethernet angeschlossen, kann auf sie zugegriffen werden und Einstellungen können aus der Ferne geändert werden. Lieferumfang: 1x Victron CMP241220000 Multiplus C 24/1200/25 Gerätekombination bestehend aus 24V 1000W Sinus Wandler + 24V 25A Batterieladegerät 1x Bedienungsanleitung

The Multiplus-II 12/3000/120-32 is a high-end device combination from Victron Energy (MPN PMP122305010) that combines classic Multiplus components with an external current sensor and integrated anti-islanding function. This extends the PowerControl and PowerAssist functions to 50 A. The inverter module delivers a full 3000 W with a non-linear load or 2400 W with a linear continuous load. The 12 V battery charger is also very well proportioned with 120 A charging power and is supplemented by a 32 A transfer switch, which can be used to switch back and forth between the AC connections at lightning speed. Important features of the Multiplus-II 12/3000/120-32 PowerControl and PowerAssist increase of mains or generator power Built-in anti-islanding function and connection option for external current sensor (optional) can be used as a backup device in grid-connected systems for power supply in the event of grid failures Can be used in various applications ideally suited for professional seafaring, yachts, vehicles and land-based, off-grid applications VE.Bus interface for parallel and three-phase operation, remote monitoring and system integration practically unlimited power thanks to parallel and three-phase operation can be configured on site or remotely using VEConfigure software* Technical features 3000 W power with non-linear load 2400 W continuous load and 5500 W peak power for 12 V battery voltage, 32 A transfer switch and 120 A battery charger Output voltage: 230 VAC, frequency: 50 Hz Max. efficiency is 95%, protection class IP22 Always enough power thanks to PowerControl and PowerAssist A maximum mains or generator current can be set on the MultiPlus-II 12/3000/120-32. The MultiPlus-II then takes account of other connected AC consumers and only uses the current that is still "left over" to charge the battery. This prevents the generator or mains connection from being overloaded (PowerControl function). The PowerAssist function adds a new dimension to the PowerControl principle. Load peaks often only occur for a limited period of time. In such cases, the MultiPlus-II immediately compensates for insufficient generator, shore power or mains power with energy from the battery. If the load is reduced, i.e. consumers are switched off, the available energy can then be used to recharge the batteries. Solar power: alternating current even in the event of a mains failure The device can be used with both off-grid and grid-connected PV systems as well as other alternative energy systems. It can be used with both solar charge controllers and grid-connected inverters. Maximum flexibility thanks to two AC outputs The main output ensures uninterrupted operation. In the event of a mains failure or an interruption in the shore/generator current, the MultiPlus-II takes over the supply to the connected loads. The switchover takes place so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic devices is guaranteed. The second output only supplies power when alternating current is available at the input of the MultiPlus-II. Consumers that must not discharge the battery, such as a water heater, can be connected to this output. Many options for system expansion The settings can be changed in a matter of minutes using the VEConfigure software (a computer or laptop and an MK3 USB interface are required) and several monitoring and control options are available: Color Control GX, Venus GX, Octo GX, CANvu GX, laptop, computer, Bluetooth (with the optional VE.Bus Smart Dongle), battery monitor, Digital Multi control panel. Remote configuration and monitoring Install a Color Control GX or other GX products to connect to the Internet. The operating data can be stored and viewed free of charge on our VRM (Victron Remote Management) website. If systems are connected to the Internet, they can be accessed remotely and settings can be changed. Scope of delivery: 1x Victron PMP122305010 Multiplus-II 12/3000/120-32A1x operating instructions

The Multiplus C 24/2000/50 from Victron (MPN CMP242200000) is a device combination of 24V 1600W sine wave inverter and battery charger. The permanently integrated battery charger delivers a remarkable 50A, which means that even large batteries can be fully charged quickly if shore/grid power is available. The 24V sine wave voltage converter built into the Multiplus converts your current from the battery into 230V alternating current. Thanks to the genuine sine wave, the power quality is also perfect for sensitive electronic devices.Comprehensive and flexible in useAs it also has a lightning-fast 30A transfer switch in addition to the inverter and charger, it is an ideal inverter for motorhomes, boats or yachts and the grid-connected area of the uninterruptible power supply in the event of grid fluctuations or power failures. Also for use in grid-connected self-consumption systems that only draw power from the supplier when the battery power is no longer sufficient or as a UPS solution in which the Multiplus steps in if the power from the grid operator suddenly fails and thus ensures an uninterruptible power supply.Key performance features of the Multiplus C 24/2000/501600W continuous power and 4000W peak power, for 24V battery voltageDevice combination of inverter with transfer switch and 50A battery chargersupplies the purest 230V sine wave voltage and a clean 50Hz frequencyVE.Bus communication port provides extensive networking, system integration, configuration and control options for Victron Multiplus devices.supports three-phase operation (3 identical units of the same model required)Multiplus devices can be connected in parallel, up to 6 devices can be connected in parallel, significantly increasing system performance if required2 AC outputs from Multiplus 3000 and larger. The second output can then be used, for example, to connect devices that should only run when mains power is availablePowerControl function enables working with limited generator output as well as limited shore or mains powerPowerAssist function enables “power boosting” of generators and shore power support if requiredCan be used as a UPS solution for uninterruptible power supplycan be used for grid-connected self-consumption systems that only draw power from the grid operator when the battery capacity is no longer sufficient or other programmable events have occurredcompatible with numerous Victron control and display panelsThree-phase operation possible with identical MultiPlus invertersMassive power expansion possibleIn addition to the parallel connection, three units of the same model can also be configured for a three-phase output. But that's not all: up to six sets of three units can be connected in parallel to achieve a huge 75 kW / 90 kVA inverter and over 2,000 A charging capacity (calculated with the 5000 version)PowerControl - working with limited generator output, limited shore or mains powerThe MultiPlus is a very powerful battery charger. It therefore draws a lot of current from the generator or shore power supply (almost 10A per 5kVA Multi at 230 VAC). The maximum mains or generator current to be drawn can be set using the Multi Control remote control panel. The MultiPlus then takes into account other connected AC consumers and only uses the current that is still “left over” for charging. This prevents the generator or shore power connection from being overloaded.PowerAssist - “power boost” for generators and shore power supportThis function adds a new dimension to the PowerControl principle. It enables the MultiPlus to support alternative sources that are too weak. Load peaks often only occur for a limited period of time. In such cases, the MultiPlus ensures that insufficient shore power or generator output is immediately compensated for by energy from the battery.BackUp system: alternating current even in the event of a power failureThe MultiPlus can be used with both off-grid and grid-connected PV systems as well as other alternative energy systems. Software is available to detect a grid failure.Simple system configurationIf settings need to be changed on a single device, this can be done in a matter of minutes using a DIP switch setting procedure.Parallel-connected and three-phase systems can be configured using the VE.Bus Quick Configure and VE.Bus System Configurator software.Monitoring options and local controlSeveral options are available: Battery Monitor, Multi Control Panel, Ve.Net Blue Power Panel, Color Control Panel, Smartphone or Tablet (Bluetooth Smart), Laptop or Computer (USB or RS232).Monitoring and control from a distanceVictron Ethernet Remote, Victron Global Remote and the Color Control Panel enable remote maintenance and remote monitoring of the MultiPlus. System data can also be stored and viewed free of charge on the VRM (Victron Remote Management) website.Remote configurationIf systems with a Color Control Panel are connected to the Ethernet, they can be accessed and settings can be changed remotely.Scope of delivery:1x Victron CMP242200000 Multiplus C 24/2000/50 device combination consisting of 24V 1600W sine wave converter + 24V 50A battery charger1x operating instructions

The Multiplus-II 24/3000/70-32 is a high-end device combination from Victron Energy (MPN PMP242305010) that combines classic Multiplus components with an external current sensor and integrated anti-islanding function. This extends the PowerControl and PowerAssist functions to 50 A and extends the potential range of use to ESS applications. The inverter module delivers a full 3000 W with a non-linear load or 2400 W with a linear continuous load. The 24 V battery charger is also very well proportioned with 70 A charging power and is supplemented by a 32 A transfer switch, which can be used to switch back and forth between the AC connections at lightning speed. Important features of the Multiplus-II 24/3000/70-32 PowerControl and PowerAssist increase mains or generator output built-in anti-islanding function and connection option for external current sensor (optional) can be used as a backup device in grid-connected systems for power supply in the event of grid failures can be used in various ESS (Energy Storage System) applications ideally suited for professional seafaring, yachts, vehicles and land-based, off-grid applications VE.Bus interface for parallel and three-phase operation, remote monitoring and system integration practically unlimited power thanks to parallel and three-phase operation can be configured on site or remotely using VEConfigure software* Technical features 3000 W power with non-linear load 2400 W continuous load and 6000 W peak power for 24 V battery voltage, 32 A transfer switch and 70 A battery charger Output voltage: 230 VAC, frequency: 50 Hz Max. efficiency is 95%, protection class IP22 Always enough power thanks to PowerControl and PowerAssist A maximum mains or generator current can be set on the MultiPlus-II 24/3000/70-32. The MultiPlus-II then takes account of other connected AC consumers and only uses the power that is still "left over" to charge the battery. This prevents the generator or mains connection from being overloaded (PowerControl function). The PowerAssist function adds a new dimension to the PowerControl principle. Load peaks often only occur for a limited period of time. In such cases, the MultiPlus-II immediately compensates for insufficient generator, shore power or mains power with energy from the battery. If the load is reduced, i.e. consumers are switched off, the available energy can then be used to recharge the batteries. Solar power: alternating current even in the event of a mains failure The device can be used with both off-grid and grid-connected PV systems as well as other alternative energy systems. It can be used with both solar charge controllers and grid-connected inverters. Maximum flexibility thanks to two AC outputs The main output ensures uninterrupted operation. In the event of a mains failure or an interruption in the shore/generator current, the MultiPlus-II takes over the supply to the connected loads. The switchover takes place so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic devices is guaranteed. The second output only supplies power when alternating current is available at the input of the MultiPlus-II. Consumers that must not discharge the battery, such as a water heater, can be connected to this output. Many options for system expansion The settings can be changed in a matter of minutes using the VEConfigure software (a computer or laptop and an MK3 USB interface are required) and several monitoring and control options are available: Color Control GX, Venus GX, Octo GX, CANvu GX, laptop, computer, Bluetooth (with the optional VE.Bus Smart Dongle), battery monitor, Digital Multi control panel. Remote configuration and monitoring Install a Color Control GX or other GX products to connect to the Internet. The operating data can be stored and viewed free of charge on our VRM (Victron Remote Management) website. If systems are connected to the Internet, they can be accessed remotely and settings can be changed. Scope of delivery: 1x Victron PMP242305010 Multiplus-II 24/3000/70-32A1x operating instructions

The Multiplus-II 24/3000/70-32 is a high-end device combination from Victron Energy (MPN PMP242305010) that combines classic Multiplus components with an external current sensor and integrated anti-islanding function. This extends the PowerControl and PowerAssist functions to 50 A and extends the potential range of use to ESS applications. The inverter module delivers a full 3000 W with a non-linear load or 2400 W with a linear continuous load. The 24 V battery charger is also very well proportioned with 70 A charging power and is supplemented by a 32 A transfer switch, which can be used to switch back and forth between the AC connections at lightning speed. Important features of the Multiplus-II 24/3000/70-32 PowerControl and PowerAssist increase mains or generator output built-in anti-islanding function and connection option for external current sensor (optional) can be used as a backup device in grid-connected systems for power supply in the event of grid failures can be used in various ESS (Energy Storage System) applications ideally suited for professional seafaring, yachts, vehicles and land-based, off-grid applications VE.Bus interface for parallel and three-phase operation, remote monitoring and system integration practically unlimited power thanks to parallel and three-phase operation can be configured on site or remotely using VEConfigure software* Technical features 3000 W power with non-linear load 2400 W continuous load and 6000 W peak power for 24 V battery voltage, 32 A transfer switch and 70 A battery charger Output voltage: 230 VAC, frequency: 50 Hz Max. efficiency is 95%, protection class IP22 Always enough power thanks to PowerControl and PowerAssist A maximum mains or generator current can be set on the MultiPlus-II 24/3000/70-32. The MultiPlus-II then takes account of other connected AC consumers and only uses the power that is still "left over" to charge the battery. This prevents the generator or mains connection from being overloaded (PowerControl function). The PowerAssist function adds a new dimension to the PowerControl principle. Load peaks often only occur for a limited period of time. In such cases, the MultiPlus-II immediately compensates for insufficient generator, shore power or mains power with energy from the battery. If the load is reduced, i.e. consumers are switched off, the available energy can then be used to recharge the batteries. Solar power: alternating current even in the event of a mains failure The device can be used with both off-grid and grid-connected PV systems as well as other alternative energy systems. It can be used with both solar charge controllers and grid-connected inverters. Maximum flexibility thanks to two AC outputs The main output ensures uninterrupted operation. In the event of a mains failure or an interruption in the shore/generator current, the MultiPlus-II takes over the supply to the connected loads. The switchover takes place so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic devices is guaranteed. The second output only supplies power when alternating current is available at the input of the MultiPlus-II. Consumers that must not discharge the battery, such as a water heater, can be connected to this output. Many options for system expansion The settings can be changed in a matter of minutes using the VEConfigure software (a computer or laptop and an MK3 USB interface are required) and several monitoring and control options are available: Color Control GX, Venus GX, Octo GX, CANvu GX, laptop, computer, Bluetooth (with the optional VE.Bus Smart Dongle), battery monitor, Digital Multi control panel. Remote configuration and monitoring Install a Color Control GX or other GX products to connect to the Internet. The operating data can be stored and viewed free of charge on our VRM (Victron Remote Management) website. If systems are connected to the Internet, they can be accessed remotely and settings can be changed. Scope of delivery: 1x Victron PMP242305010 Multiplus-II 24/3000/70-32A1x operating instructions

The Multiplus-II 48/3000/35-32 is a high-end device combination from Victron Energy (MPN PMP482305010) that combines classic Multiplus components with an external current sensor and integrated anti-islanding function. This extends the PowerControl and PowerAssist functions to 50 A and extends the potential range of use to ESS applications. The inverter module delivers a full 3000 W with a non-linear load and 2400 W with a linear continuous load. The 48 V battery charger is also very well proportioned with 35 A charging power and is supplemented by a 32 A transfer switch, which can be used to switch back and forth between the AC connections at lightning speed. Important features of the Multiplus-II 48/3000/35-32 PowerControl and PowerAssist increase of mains or generator power Built-in anti-islanding function and connection option for external current sensor (optional) can be used as a backup device in grid-connected systems for power supply in the event of grid failures can be used in various ESS (Energy Storage System) applications ideally suited for professional seafaring, yachts, vehicles and land-based, off-grid applications VE.Bus interface for parallel and three-phase operation, remote monitoring and system integration practically unlimited power thanks to parallel and three-phase operation can be configured on site or remotely using VEConfigure software* Technical features 3000W power with non-linear load 2400 W continuous load and 6000 W peak power for 48 V battery voltage, 32 A transfer switch and 35 A battery charger Output voltage: 230 VAC, frequency: 50 Hz Max. efficiency is 95%, protection class IP22 Always enough power thanks to PowerControl and PowerAssist A maximum mains or generator current can be set on the MultiPlus-II 48/3000/35-32. The MultiPlus-II then takes account of other connected AC consumers and only uses the power that is still "left over" to charge the battery. This prevents the generator or mains connection from being overloaded (PowerControl function). The PowerAssist function adds a new dimension to the PowerControl principle. Load peaks often only occur for a limited period of time. In such cases, the MultiPlus-II immediately compensates for insufficient generator, shore power or mains power with energy from the battery. If the load is reduced, i.e. consumers are switched off, the available energy can then be used to recharge the batteries. Solar power: alternating current even in the event of a mains failure The device can be used with both off-grid and grid-connected PV systems as well as other alternative energy systems. It can be used with both solar charge controllers and grid-connected inverters. Maximum flexibility thanks to two AC outputs The main output ensures uninterrupted operation. In the event of a mains failure or an interruption in the shore/generator current, the MultiPlus-II takes over the supply to the connected loads. The switchover takes place so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic devices is guaranteed. The second output only supplies power when alternating current is available at the input of the MultiPlus-II. Consumers that must not discharge the battery, such as a water heater, can be connected to this output. Many options for system expansion The settings can be changed in a matter of minutes using the VEConfigure software (a computer or laptop and an MK3 USB interface are required) and several monitoring and control options are available: Color Control GX, Venus GX, Octo GX, CANvu GX, laptop, computer, Bluetooth (with the optional VE.Bus Smart Dongle), battery monitor, Digital Multi control panel. Remote configuration and monitoring Install a Color Control GX or other GX products to connect to the Internet. The operating data can be stored and viewed free of charge on our VRM (Victron Remote Management) website. If systems are connected to the Internet, they can be accessed remotely and settings can be changed. Scope of delivery: 1x Victron PMP482305010 Multiplus-II 48/3000/35-32A1x operating instructions

The Multiplus-II 48/8000/110-100 is a high-end device combination from Victron Energy (MPN PMP482805000) that combines classic Multiplus components with an external current sensor and integrated anti-islanding function. This extends the PowerControl and PowerAssist functions to 100 A and extends the potential range of use to ESS applications. The inverter module delivers a full 8000 W with a non-linear load and 6400 W with a linear continuous load. The 48 V battery charger is also very well proportioned with 110 A charging power and is supplemented by a 100 A transfer switch, which can be used to switch back and forth between the AC connections at lightning speed. Important features of the Multiplus-II 48/8000/110-100 PowerControl and PowerAssist - increase of mains or generator powerBuilt-in anti-islanding function and connection option for external current sensor (optional)can be used as a backup device in grid-connected systems for power supply in the event of grid failurescan be used in various ESS (Energy Storage System) applicationsideally suited for professional seafaring, yachts, vehicles and land-based, off-grid applicationsVE.Bus interface for parallel and three-phase operation, remote monitoring and system integrationpractically unlimited power thanks to parallel and three-phase operationcan be configured on site or remotely using VEConfigure software* Technical features 8000 W power with non-linear load 6400 W continuous load and 15000 W peak powerfor 48 V battery voltage, 100 A transfer switch and 110 A battery chargerOutput voltage: 230 VAC, frequency: 50 HzMax. efficiency is 95%, protection class IP22 Always enough power thanks to PowerControl and PowerAssist A maximum mains or generator current can be set on the MultiPlus-II 48/8000/110-100. The MultiPlus-II then takes account of other connected AC consumers and only uses the power that is still "left over" to charge the battery. This prevents the generator or mains connection from being overloaded (PowerControl function). The PowerAssist function adds a new dimension to the PowerControl principle. Load peaks often only occur for a limited period of time. In such cases, the MultiPlus-II immediately compensates for insufficient generator, shore power or mains power with energy from the battery. If the load is reduced, i.e. consumers are switched off, the available energy can then be used to recharge the batteries. Solar power: alternating current even in the event of a mains failure The device can be used with both off-grid and grid-connected PV systems as well as other alternative energy systems. It can be used with both solar charge controllers and grid-connected inverters. Maximum flexibility thanks to two AC outputs The main output ensures uninterrupted operation. In the event of a mains failure or an interruption in the shore/generator current, the MultiPlus-II takes over the supply to the connected loads. The switchover takes place so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic devices is guaranteed. The second output only supplies power when alternating current is available at the input of the MultiPlus-II. Consumers that must not discharge the battery, such as a water heater, can be connected to this output. Many options for system expansion The settings can be changed in a matter of minutes using the VEConfigure software (a computer or laptop and an MK3 USB interface are required) and several monitoring and control options are available: Color Control GX, Venus GX, Octo GX, CANvu GX, laptop, computer, Bluetooth (with the optional VE.Bus Smart Dongle), battery monitor, Digital Multi control panel. Remote configuration and monitoring Install a Color Control GX or other GX products to connect to the Internet. The operating data can be stored and viewed free of charge on our VRM (Victron Remote Management) website. If systems are connected to the Internet, they can be accessed remotely and settings can be changed. Scope of delivery: 1x Victron PMP482805000 Multiplus-II 48/8000/110-100A 1x operating instructions

The Multiplus-II 48/10000/140-100 is a high-end device combination from Victron Energy (MPN PMP483105000) that combines classic Multiplus components with an external current sensor and integrated anti-islanding function. This extends the PowerControl and PowerAssist functions to 100 A and extends the potential range of use to ESS applications. The inverter module delivers a full 10000 W with a non-linear load or 8000 W with a linear continuous load. The 48 V battery charger is also very well proportioned with 140 A charging power and is supplemented by a 100 A transfer switch, which can be used to switch back and forth between the AC connections at lightning speed. Important features of the Multiplus-II 48/10000/140-100 PowerControl and PowerAssist increase of mains or generator powerbuilt-in anti-islanding function and connection option for external current sensor (optional)can be used as a backup device in grid-connected systems for power supply in the event of grid failurescan be used in various ESS (Energy Storage System) applicationsideally suited for professional seafaring, yachts, vehicles and land-based, off-grid applicationsVE.Bus interface for parallel and three-phase operation, remote monitoring and system integrationpractically unlimited power thanks to parallel and three-phase operationcan be configured on site or remotely using VEConfigure software* Technical features 10000 W power with non-linear load 8000 W continuous load and 18000 W peak powerfor 48 V battery voltage, 100 A transfer switch and 140 A battery chargerOutput voltage: 230 VAC, frequency: 50 HzMax. efficiency is 95%, protection class IP22 Always enough power thanks to PowerControl and PowerAssist A maximum mains or generator current can be set on the MultiPlus-II 48/10000/140-100. The MultiPlus-II then takes account of other connected AC consumers and only uses the power that is still "left over" to charge the battery. This prevents the generator or mains connection from being overloaded (PowerControl function). The PowerAssist function adds a new dimension to the PowerControl principle. Load peaks often only occur for a limited period of time. In such cases, the MultiPlus-II immediately compensates for insufficient generator, shore power or mains power with energy from the battery. If the load is reduced, i.e. consumers are switched off, the available energy can then be used to recharge the batteries. Solar power: alternating current even in the event of a mains failure The device can be used with both off-grid and grid-connected PV systems as well as other alternative energy systems. It can be used with both solar charge controllers and grid-connected inverters. Maximum flexibility thanks to two AC outputs The main output ensures uninterrupted operation. In the event of a mains failure or an interruption in the shore/generator current, the MultiPlus-II takes over the supply to the connected loads. The switchover takes place so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic devices is guaranteed. The second output only supplies power when alternating current is available at the input of the MultiPlus-II. Consumers that must not discharge the battery, such as a water heater, can be connected to this output. Many options for system expansion The settings can be changed in a matter of minutes using the VEConfigure software (a computer or laptop and an MK3 USB interface are required) and several monitoring and control options are available: Color Control GX, Venus GX, Octo GX, CANvu GX, laptop, computer, Bluetooth (with the optional VE.Bus Smart Dongle), battery monitor, Digital Multi control panel. Remote configuration and monitoring Install a Color Control GX or other GX products to connect to the Internet. The operating data can be stored and viewed free of charge on our VRM (Victron Remote Management) website. If systems are connected to the Internet, they can be accessed remotely and settings can be changed. Scope of delivery: 1x Victron PMP483105000 Multiplus-II 48/10000/140-100A 1x operating instructions

The Multiplus-II 48/5000/70-50 is a high-end device combination from Victron Energy (MPN PMP482505010) that combines classic Multiplus components with an external current sensor and integrated anti-islanding function. This extends the PowerControl and PowerAssist functions to 100 A and extends the potential range of use to ESS applications. The inverter module delivers a full 5000 W with a non-linear load and 4000 W with a linear continuous load. The 48 V battery charger is also very well proportioned with 70 A charging power and is supplemented by a 50 A transfer switch, which can be used to switch back and forth between the AC connections at lightning speed. Important features of the Multiplus-II 48/5000/70-50 PowerControl and PowerAssist increase of mains or generator powerbuilt-in anti-islanding function and connection option for external current sensor (optional)can be used as a backup device in grid-connected systems for power supply in the event of grid failurescan be used in various ESS (Energy Storage System) applicationsideally suited for professional seafaring, yachts, vehicles and land-based, off-grid applicationsVE.Bus interface for parallel and three-phase operation, remote monitoring and system integrationpractically unlimited power thanks to parallel and three-phase operationcan be configured on site or remotely using VEConfigure software* Technical features 5000 W power with non-linear load 4000 W continuous load and 9000 W peak powerfor 48 V battery voltage, 50 A transfer switch and 70 A battery chargerOutput voltage: 230 VAC, frequency: 50 Hzmax. efficiency is 95%, protection class IP22 Always enough power thanks to PowerControl and PowerAssist A maximum mains or generator current can be set on the MultiPlus-II 48/5000/70-50. The MultiPlus-II then takes account of other connected AC consumers and only uses the power that is still "left over" to charge the battery. This prevents the generator or mains connection from being overloaded (PowerControl function). The PowerAssist function adds a new dimension to the PowerControl principle. Load peaks often only occur for a limited period of time. In such cases, the MultiPlus-II immediately compensates for insufficient generator, shore power or mains power with energy from the battery. If the load is reduced, i.e. consumers are switched off, the available energy can then be used to recharge the batteries. Solar power: alternating current even in the event of a mains failure The device can be used with both off-grid and grid-connected PV systems as well as other alternative energy systems. It can be used with both solar charge controllers and grid-connected inverters. Maximum flexibility thanks to two AC outputs The main output ensures uninterrupted operation. In the event of a mains failure or an interruption in the shore/generator current, the MultiPlus-II takes over the supply to the connected loads. The switchover takes place so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic devices is guaranteed. The second output only supplies power when alternating current is available at the input of the MultiPlus-II. Consumers that must not discharge the battery, such as a water heater, can be connected to this output. Many options for system expansion The settings can be changed in a matter of minutes using the VEConfigure software (a computer or laptop and an MK3 USB interface are required) and several monitoring and control options are available: Color Control GX, Venus GX, Octo GX, CANvu GX, laptop, computer, Bluetooth (with the optional VE.Bus Smart Dongle), battery monitor, Digital Multi control panel. Remote configuration and monitoring Install a Color Control GX or other GX products to connect to the Internet. The operating data can be stored and viewed free of charge on our VRM (Victron Remote Management) website. If systems are connected to the Internet, they can be accessed remotely and settings can be changed. Scope of delivery: 1x Victron PMP482505010 Multiplus-II 48/5000/70-50A 1x operating instructions

The new MultiPlus 12/800/35-16 (Victron Energy, PMP121800000) is the successor to the Multiplus Compact 12/800 and is a modern device combination consisting of a powerful inverter with pure sine wave, an advanced 50A battery charger that uses adaptive charging technology and a 16A high-speed AC voltage transfer switch.In the event of a mains fault or if the shore power or on-board generator is interrupted, the Multi's inverter is automatically switched on and takes over the supply to the connected loads. The switchover happens so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic devices is guaranteed.Key features of the MultiPlus 12/800/35-16Cont. Output power at 25°C: 700W / 800W with non-linear loadVictron Energy MPN: PMP121800000for 12V system voltageintegrated 35A mains charger for your batteriesintegrated 16A mains transfer switchUPS operation possibleExtensive range of accessories availableCan be used in numerous areas of application, whether on land or mobileProven reliabilityComplete bridging with an additional toroidal transformer topology has proven itself over many years. The inverter is short-circuit-proof and protected against overheating (whether caused by overload or ambient temperature).PowerControl - (Multiplus 800VA 1200VA only)The maximum mains or generator current to be drawn can be set using the Multi Control remote control panel. The MultiPlus then takes account of other connected AC consumers and only uses the current that is still “left over” for charging. This prevents the generator or shore power connection from being overloaded.PowerAssist - (Multiplus 800VA 1200VA only)Load peaks often only occur for a limited period of time. In such cases, the MultiPlus ensures that insufficient shore power or generator output is immediately compensated for by energy from the battery. If the load is reduced, i.e. consumers are switched off, the available energy can then be used to recharge the batteries.High switch-on powerThis is required to switch on loads with high inrush currents, such as voltage converters for LED lamps, halogen lamps or power tools.Search modeIf the search mode is set to 'on', the power consumption of the inverter is reduced by around 70% in no-load operation. In this mode, when operated in inverter mode, the Multi switches off at zero load or at low load and switches on again every two seconds for a short period. If the output current exceeds a set limit value, the inverter resumes operation. If this is not the case, the inverter switches off again.Programmable relayIn the default setting, the multifunction relay acts as an alarm relay, i.e. it switches the device off in the event of faults (device gets too hot, ripple voltage at the input too high, battery voltage too low).Scope of delivery:Victron Energy PMP121800000, MultiPlus 12/800/35-16

The Multiplus-II 48/5000/70-50 is a high-end device combination from Victron Energy (MPN PMP482505010) that combines classic Multiplus components with an external current sensor and integrated anti-islanding function. This extends the PowerControl and PowerAssist functions to 100 A and extends the potential range of use to ESS applications. The inverter module delivers a full 5000 W with a non-linear load and 4000 W with a linear continuous load. The 48 V battery charger is also very well proportioned with 70 A charging power and is supplemented by a 50 A transfer switch, which can be used to switch back and forth between the AC connections at lightning speed. Important features of the Multiplus-II 48/5000/70-50 PowerControl and PowerAssist increase of mains or generator powerbuilt-in anti-islanding function and connection option for external current sensor (optional)can be used as a backup device in grid-connected systems for power supply in the event of grid failurescan be used in various ESS (Energy Storage System) applicationsideally suited for professional seafaring, yachts, vehicles and land-based, off-grid applicationsVE.Bus interface for parallel and three-phase operation, remote monitoring and system integrationpractically unlimited power thanks to parallel and three-phase operationcan be configured on site or remotely using VEConfigure software* Technical features 5000 W power with non-linear load 4000 W continuous load and 9000 W peak powerfor 48 V battery voltage, 50 A transfer switch and 70 A battery chargerOutput voltage: 230 VAC, frequency: 50 Hzmax. efficiency is 95%, protection class IP22 Always enough power thanks to PowerControl and PowerAssist A maximum mains or generator current can be set on the MultiPlus-II 48/5000/70-50. The MultiPlus-II then takes account of other connected AC consumers and only uses the power that is still "left over" to charge the battery. This prevents the generator or mains connection from being overloaded (PowerControl function). The PowerAssist function adds a new dimension to the PowerControl principle. Load peaks often only occur for a limited period of time. In such cases, the MultiPlus-II immediately compensates for insufficient generator, shore power or mains power with energy from the battery. If the load is reduced, i.e. consumers are switched off, the available energy can then be used to recharge the batteries. Solar power: alternating current even in the event of a mains failure The device can be used with both off-grid and grid-connected PV systems as well as other alternative energy systems. It can be used with both solar charge controllers and grid-connected inverters. Maximum flexibility thanks to two AC outputs The main output ensures uninterrupted operation. In the event of a mains failure or an interruption in the shore/generator current, the MultiPlus-II takes over the supply to the connected loads. The switchover takes place so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic devices is guaranteed. The second output only supplies power when alternating current is available at the input of the MultiPlus-II. Consumers that must not discharge the battery, such as a water heater, can be connected to this output. Many options for system expansion The settings can be changed in a matter of minutes using the VEConfigure software (a computer or laptop and an MK3 USB interface are required) and several monitoring and control options are available: Color Control GX, Venus GX, Octo GX, CANvu GX, laptop, computer, Bluetooth (with the optional VE.Bus Smart Dongle), battery monitor, Digital Multi control panel. Remote configuration and monitoring Install a Color Control GX or other GX products to connect to the Internet. The operating data can be stored and viewed free of charge on our VRM (Victron Remote Management) website. If systems are connected to the Internet, they can be accessed remotely and settings can be changed. Scope of delivery: 1x Victron PMP482505010 Multiplus-II 48/5000/70-50A 1x operating instructions

The Multiplus-II 48/3000/35-32 is a high-end device combination from Victron Energy (MPN PMP482305010) that combines classic Multiplus components with an external current sensor and integrated anti-islanding function. This extends the PowerControl and PowerAssist functions to 50 A and extends the potential range of use to ESS applications. The inverter module delivers a full 3000 W with a non-linear load and 2400 W with a linear continuous load. The 48 V battery charger is also very well proportioned with 35 A charging power and is supplemented by a 32 A transfer switch, which can be used to switch back and forth between the AC connections at lightning speed. Important features of the Multiplus-II 48/3000/35-32 PowerControl and PowerAssist increase of mains or generator power Built-in anti-islanding function and connection option for external current sensor (optional) can be used as a backup device in grid-connected systems for power supply in the event of grid failures can be used in various ESS (Energy Storage System) applications ideally suited for professional seafaring, yachts, vehicles and land-based, off-grid applications VE.Bus interface for parallel and three-phase operation, remote monitoring and system integration practically unlimited power thanks to parallel and three-phase operation can be configured on site or remotely using VEConfigure software* Technical features 3000W power with non-linear load 2400 W continuous load and 6000 W peak power for 48 V battery voltage, 32 A transfer switch and 35 A battery charger Output voltage: 230 VAC, frequency: 50 Hz Max. efficiency is 95%, protection class IP22 Always enough power thanks to PowerControl and PowerAssist A maximum mains or generator current can be set on the MultiPlus-II 48/3000/35-32. The MultiPlus-II then takes account of other connected AC consumers and only uses the power that is still "left over" to charge the battery. This prevents the generator or mains connection from being overloaded (PowerControl function). The PowerAssist function adds a new dimension to the PowerControl principle. Load peaks often only occur for a limited period of time. In such cases, the MultiPlus-II immediately compensates for insufficient generator, shore power or mains power with energy from the battery. If the load is reduced, i.e. consumers are switched off, the available energy can then be used to recharge the batteries. Solar power: alternating current even in the event of a mains failure The device can be used with both off-grid and grid-connected PV systems as well as other alternative energy systems. It can be used with both solar charge controllers and grid-connected inverters. Maximum flexibility thanks to two AC outputs The main output ensures uninterrupted operation. In the event of a mains failure or an interruption in the shore/generator current, the MultiPlus-II takes over the supply to the connected loads. The switchover takes place so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic devices is guaranteed. The second output only supplies power when alternating current is available at the input of the MultiPlus-II. Consumers that must not discharge the battery, such as a water heater, can be connected to this output. Many options for system expansion The settings can be changed in a matter of minutes using the VEConfigure software (a computer or laptop and an MK3 USB interface are required) and several monitoring and control options are available: Color Control GX, Venus GX, Octo GX, CANvu GX, laptop, computer, Bluetooth (with the optional VE.Bus Smart Dongle), battery monitor, Digital Multi control panel. Remote configuration and monitoring Install a Color Control GX or other GX products to connect to the Internet. The operating data can be stored and viewed free of charge on our VRM (Victron Remote Management) website. If systems are connected to the Internet, they can be accessed remotely and settings can be changed. Scope of delivery: 1x Victron PMP482305010 Multiplus-II 48/3000/35-32A1x operating instructions

The Multiplus-II 48/8000/110-100 is a high-end device combination from Victron Energy (MPN PMP482805000) that combines classic Multiplus components with an external current sensor and integrated anti-islanding function. This extends the PowerControl and PowerAssist functions to 100 A and extends the potential range of use to ESS applications. The inverter module delivers a full 8000 W with a non-linear load and 6400 W with a linear continuous load. The 48 V battery charger is also very well proportioned with 110 A charging power and is supplemented by a 100 A transfer switch, which can be used to switch back and forth between the AC connections at lightning speed. Important features of the Multiplus-II 48/8000/110-100 PowerControl and PowerAssist - increase of mains or generator powerBuilt-in anti-islanding function and connection option for external current sensor (optional)can be used as a backup device in grid-connected systems for power supply in the event of grid failurescan be used in various ESS (Energy Storage System) applicationsideally suited for professional seafaring, yachts, vehicles and land-based, off-grid applicationsVE.Bus interface for parallel and three-phase operation, remote monitoring and system integrationpractically unlimited power thanks to parallel and three-phase operationcan be configured on site or remotely using VEConfigure software* Technical features 8000 W power with non-linear load 6400 W continuous load and 15000 W peak powerfor 48 V battery voltage, 100 A transfer switch and 110 A battery chargerOutput voltage: 230 VAC, frequency: 50 HzMax. efficiency is 95%, protection class IP22 Always enough power thanks to PowerControl and PowerAssist A maximum mains or generator current can be set on the MultiPlus-II 48/8000/110-100. The MultiPlus-II then takes account of other connected AC consumers and only uses the power that is still "left over" to charge the battery. This prevents the generator or mains connection from being overloaded (PowerControl function). The PowerAssist function adds a new dimension to the PowerControl principle. Load peaks often only occur for a limited period of time. In such cases, the MultiPlus-II immediately compensates for insufficient generator, shore power or mains power with energy from the battery. If the load is reduced, i.e. consumers are switched off, the available energy can then be used to recharge the batteries. Solar power: alternating current even in the event of a mains failure The device can be used with both off-grid and grid-connected PV systems as well as other alternative energy systems. It can be used with both solar charge controllers and grid-connected inverters. Maximum flexibility thanks to two AC outputs The main output ensures uninterrupted operation. In the event of a mains failure or an interruption in the shore/generator current, the MultiPlus-II takes over the supply to the connected loads. The switchover takes place so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic devices is guaranteed. The second output only supplies power when alternating current is available at the input of the MultiPlus-II. Consumers that must not discharge the battery, such as a water heater, can be connected to this output. Many options for system expansion The settings can be changed in a matter of minutes using the VEConfigure software (a computer or laptop and an MK3 USB interface are required) and several monitoring and control options are available: Color Control GX, Venus GX, Octo GX, CANvu GX, laptop, computer, Bluetooth (with the optional VE.Bus Smart Dongle), battery monitor, Digital Multi control panel. Remote configuration and monitoring Install a Color Control GX or other GX products to connect to the Internet. The operating data can be stored and viewed free of charge on our VRM (Victron Remote Management) website. If systems are connected to the Internet, they can be accessed remotely and settings can be changed. Scope of delivery: 1x Victron PMP482805000 Multiplus-II 48/8000/110-100A 1x operating instructions

The Quattro 24/3000/70-50/50 from Victron (MPN QUA243020010) is a device combination of a 24V 2400W sine wave inverter, a powerful battery charger and transfer switch. It has two switchable AC outputs and 2 AC inputs, each equipped with a 50A transfer switch. The Quattro can be connected to two independent AC sources: for example, to the public power grid and a generator or to two generators. The Quattro automatically connects to the active source. The permanently integrated battery charger delivers an impressive 70A, which means that even large batteries can be fully charged quickly if shore/grid power is available. The 12V sine wave voltage converter built into the Quattro converts your battery current into 230V alternating current. Thanks to the true sine wave, the power quality is also perfect for sensitive electronic devices. In addition to the two integrated device types, 1 lightning-fast 50A transfer switch is installed for each AC input. Thanks to these switches, countless applications can also be implemented in the mains-coupled area. In addition to the VE.Bus port, 2 COM ports are also available for system integration, which enables virtually limitless networking of the Quattro. Extremely flexible thanks to 2 AC inputs and 2 AC outputsThe main output ensures uninterrupted operation. In the event of a mains failure or an interruption in the shore/generator power, the Quattro takes over the supply to the connected loads. The switchover happens so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic devices is guaranteed. The second output only supplies power if alternating current is available at one of the Quattro's inputs. Consumers that must not discharge the battery, such as a water heater, can be connected to this output. Key performance features of the Quattro 24/3000/70-50/502400W continuous power and 6000W peak power, for 24V battery voltageDevice combination of inverter with transfer switch and 70A battery chargersupplies the purest 230V sine wave voltage and a clean 50Hz frequency2 AC inputs with integrated transfer switch / 2 x 50 A maximum switchable current2 AC outputs + 1x additional output, which only allows the current to pass to the consumer when the AC input is active.VE.Bus communication port provides extensive networking, system integration, configuration and control options for Victron Multiplus devices.supports three-phase operation (3 identical units of the same model required)Multiplus devices can be connected in parallel, up to 6 devices can be connected in parallel, significantly increasing system performance if required2x COM ports are available in addition to the VE.Bus port, so there are virtually no limits to system integrationPowerControl function enables working with limited generator power as well as limited shore or mains powerPowerAssist function enables “power boosting” of generators and shore power support if requiredCan be used as a UPS solution for uninterruptible power supply, thanks to the integrated transfer switch with 16A or 50Acan be used for grid-connected self-consumption systems that only draw power from the grid operator when the battery capacity is no longer sufficient or other programmable events have occurred3 separately programmable relaysCompatible with numerous Victron control and display panelsVery high efficiency and low self-consumption Massive power expansion possibleUp to 6 Quattros can be connected in parallel. With six 48/10000/140 units, for example, this results in 54 kW/60 kVA power or 840 A charging current. Three units can be connected in a three-phase configuration. But that's not all: up to 6 sets of three units can be connected in parallel, resulting in 162 kW/180 kVA inverter power and over 2,500 A charging capacity.PowerControl - working with limited generator output, limited shore or mains powerThe MultiPlus is a very powerful battery charger. It therefore draws a lot of current from the generator or shore power supply (almost 10A per 5kVA Multi at 230 VAC). The maximum mains or generator current to be drawn can be set using the Multi Control remote control panel. The MultiPlus then takes other connected AC consumers into account and only uses the current that is still “left over” for charging. This prevents the generator or shore power connection from being overloaded. PowerAssist - “power boost” for generators and shore power supportThis function adds a new dimension to the PowerControl principle. It enables the Quattro to support alternative sources that are too weak. Load peaks often only occur for a limited period of time. In such cases, the Quattro ensures that insufficient shore power or generator output is immediately compensated for by energy from the battery. BackUp system: alternating current even in the event of a power failureThe Quattro can be used with non-grid-connected and grid-connected PV systems as well as other alternative energy systems. Software is available to detect a grid failure. Simple system configurationIf settings need to be changed on a single device, this can be done in a matter of minutes using a DIP switch setting procedure.Parallel and three-phase systems can be configured using the VE.Bus Quick Configure and VE.Bus System Configurator software.Monitoring options and local controlSeveral options are available: Battery Monitor, Multi Control Panel, Ve.Net Blue Power Panel, Color Control Panel, Smartphone or Tablet (Bluetooth Smart), Laptop or Computer (USB or RS232).Monitoring and control from a distanceVictron Ethernet Remote, Victron Global Remote and the Color Control Panel enable remote maintenance and remote monitoring of the MultiPlus. System data can also be saved and viewed free of charge on the VRM (Victron Remote Management) website.Remote configurationIf systems with a Color Control Panel are connected to the Ethernet, they can be accessed and settings can be changed remotely.Scope of delivery:1x Victron QUA243020010 Quattro 24/3000/70-50/50 device combination consisting of 24V 2400W sine wave converter + 24V 70A battery charger + 2 AC inputs with integrated 50A transfer switches1x instruction manual

The Quattro 48/5000/70-100/100 from Victron (MPN QUA485021010) is a device combination of a 48V 4000W sine wave inverter, a powerful battery charger and transfer switch. It has two switchable AC outputs and 2 AC inputs, each equipped with a 100A transfer switch. The Quattro can be connected to two independent AC power sources: for example, to the public power grid and a generator or to two generators. The Quattro automatically connects to the active source.The permanently integrated battery charger delivers an impressive 70A, which means that even large batteries can be fully charged quickly if shore/grid power is available. The 48V sine wave voltage converter built into the Quattro converts your battery current into 230V alternating current. Thanks to the true sine wave, the power quality is also perfect for sensitive electronic devices. In addition to the two integrated device types, 1 lightning-fast 100A transfer switch is installed for each AC input. Thanks to these switches, countless applications can also be implemented in the mains-coupled area. In addition to the VE.Bus port, 2 COM ports are also available for system integration, enabling virtually limitless networking of the Quattro.Extremely flexible thanks to 2 AC inputs and 2 AC outputsThe main output ensures uninterrupted operation. In the event of a mains failure or an interruption in the shore/generator power, the Quattro takes over the supply to the connected loads. The switchover happens so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic devices is guaranteed. The second output only supplies power if alternating current is available at one of the Quattro's inputs. Consumers that must not discharge the battery, such as a water heater, can be connected to this output.Key performance features of the Quattro 48/5000/70-100/1004000W continuous power and 10000W peak power, for 48V battery voltageDevice combination of inverter with transfer switch and 70A battery chargersupplies the purest 230V sine wave voltage and a clean 50Hz frequency2 AC inputs with integrated transfer switch / 2 x 100 A maximum switchable current2 AC outputs + 1x additional output which only allows the current to pass to the load when the AC input is active.VE.Bus communication port provides extensive networking, system integration, configuration and control options for Victron's Multiplus devices.supports three-phase operation (3 identical units of the same model required)Multiplus devices can be connected in parallel, up to 6 devices can be connected in parallel, significantly increasing system performance if required2x COM ports are available in addition to the VE. Bus port, so there are virtually no limits to system integrationPowerControl function enables working with limited generator power as well as limited shore or mains powerPowerAssist function enables "power boost" of generators and shore connection support if requiredcan be used as a UPS solution for uninterruptible power supply, thanks to the integrated transfer switch with 100A can be used for grid-connected self-consumption systems that only draw power from the grid operator when the battery capacity is no longer sufficient or other programmable events have occurred3 separately programmable relayscompatible with numerous Victron control and display panelsvery high efficiency and low self-consumptionmassive power expansion possibleUp to 6 Quattros can be connected in parallel. With six 48/10000/140 units, for example, this results in 54 kW/60 kVA power or 840 A charging current. Three units can be connected in a three-phase configuration. But that's not all: up to 6 sets of three units can be connected in parallel, resulting in 162 kW/180 kVA inverter power and over 2,500 A charging capacity.PowerControl - working with limited generator output, restricted shore or mains power The MultiPlus is a very powerful battery charger. It therefore draws a lot of current from the generator or shore power supply (almost 10A per 5kVA Multi at 230 VAC). The maximum mains or generator current to be drawn can be set using the Multi Control remote control panel. The MultiPlus then takes into account other connected AC consumers and only uses the current that is still "left over" for charging. This prevents the generator or shore power connection from being overloaded.PowerAssist - "power boost" for generators and shore power supportThis function adds a new dimension to the PowerControl principle. It enables the Quattro to support alternative sources that are too weak. Load peaks often only occur for a limited period of time. In such cases, the Quattro ensures that insufficient shore power or generator output is immediately compensated for by energy from the battery.BackUp system: Alternating current even in the event of a grid failureThe Quattro can be used with both non-grid-connected and grid-connected PV systems as well as other alternative energy systems. Software is available to detect a grid failure.Simple system configurationIf settings need to be changed on an individual device, this can be done within a few minutes using a DIP switch setting procedure.Parallel and three-phase systems can be configured using the VE.Bus Quick Configure and VE.Bus System Configurator software.Monitoring options and local controlSeveral options are available: Battery monitor, Multi Control Panel, Ve.Net Blue Power Panel, Color Control Panel, smartphone or tablet (Bluetooth Smart), laptop or computer (USB or RS232).Remote monitoring and controlVictron Ethernet Remote, Victron Global Remote and the Color Control Panel enable remote maintenance and remote monitoring of the MultiPlus. System data can also be saved and viewed free of charge on the VRM (Victron Remote Management) website.Remote configurationIf systems with a Color Control Panel are connected to the Ethernet, they can be accessed and settings can be changed remotely.Scope of delivery:1x Victron QUA485021010 Quattro 48/5000/70-100/100 device combination consisting of 48V 4000W sine wave converter + 48V 70A battery charger + 2 AC inputs with integrated 100A transfer switches1x operating manual

The Quattro 12/3000/120-50/50 from Victron (MPN QUA123020010) is a device combination of a 12V 2400W sine wave inverter, a powerful battery charger and transfer switch. It has two switchable AC outputs and 2 AC inputs. The Quattro can be connected to two independent AC power sources: for example to the public power grid and a generator or to two generators. The Quattro automatically connects to the active source.The permanently integrated battery charger delivers an impressive 120A, which means that even large batteries can be fully charged quickly if shore/grid power is available. The 12V sine wave voltage converter built into the Quattro converts your battery current into 230V alternating current. Thanks to the true sine wave, the power quality is also perfect for sensitive electronic devices. In addition to the two integrated device types, 1 lightning-fast 50A transfer switch is installed for each AC input. Thanks to these switches, countless applications can also be implemented in the mains-coupled area. In addition to the VE.Bus port, 2 COM ports are also available for system integration, allowing virtually limitless networking of the Quattro.Extremely flexible thanks to 2 AC inputs and 2 AC outputsThe main output ensures uninterrupted operation. In the event of a mains failure or an interruption in the shore/generator power, the Quattro takes over the supply to the connected loads. The switchover happens so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic devices is guaranteed. The second output only supplies power if alternating current is available at one of the Quattro's inputs. Consumers that must not discharge the battery, such as a water heater, can be connected to this output.Key performance features of the Quattro 12/3000/120-50/502400W continuous power and 6000W peak power, for 12V battery voltageDevice combination of inverter with transfer switch and 120A battery chargersupplies the purest 230V sine wave voltage and a clean 50Hz frequency2 AC inputs with integrated transfer switch / 2 x 50 A maximum switchable current2 AC outputs + 1x additional output which only allows the current to pass to the consumer when the AC input is active.VE.Bus communication port provides extensive networking, system integration, configuration and control options for Victron Multiplus devices.supports three-phase operation (3 identical units of the same model required)Quattro devices can be connected in parallel, up to 6 devices can be connected in parallel, significantly increasing system performance if required2x COM ports are available in addition to the VE.Bus port, so there are virtually no limits to system integrationPowerControl function enables working with limited generator power as well as limited shore or mains powerPowerAssist function enables “power boosting” of generators and shore power support if requiredCan be used as a UPS solution for uninterruptible power supply, thanks to the integrated transfer switch with 16A or 50Acan be used for grid-connected self-consumption systems that only draw power from the grid operator when the battery capacity is no longer sufficient or other programmable events have occurred3 separately programmable relayscompatible with numerous Victron control and display panelsVery high efficiency and low self-consumptionMassive power expansion possibleUp to 6 Quattros can be connected in parallel. With six 48/10000/140 units, for example, this results in 54 kW/60 kVA power or 840 A charging current. Three units can be connected in a three-phase configuration. But that's not all: up to 6 sets of three units can be connected in parallel, resulting in 162 kW/180 kVA inverter power and over 2,500 A charging capacity.PowerControl - working with limited generator output, limited shore or mains powerThe MultiPlus is a very powerful battery charger. It therefore draws a lot of current from the generator or shore power supply (almost 10A per 5kVA Multi at 230 VAC). The maximum mains or generator current to be drawn can be set using the Multi Control remote control panel. The MultiPlus then takes other connected AC consumers into account and only uses the current that is still “left over” for charging. This prevents the generator or shore power connection from being overloaded.PowerAssist - “power boost” for generators and shore power supportThis function adds a new dimension to the PowerControl principle. It enables the Quattro to support alternative sources that are too weak. Load peaks often only occur for a limited period of time. In such cases, the MultiPlus ensures that insufficient shore power or generator output is immediately compensated for by energy from the battery.BackUp system: alternating current even in the event of a power failureThe Quattro can be used with non-grid-connected and grid-connected PV systems as well as other alternative energy systems. Software is available to detect a grid failure.Simple system configurationIf settings need to be changed on a single device, this can be done in a matter of minutes using a DIP switch setting procedure.Parallel-connected and three-phase systems can be configured using the VE.Bus Quick Configure and VE.Bus System Configurator software.Monitoring options and local controlSeveral options are available: Battery Monitor, Multi Control Panel, Ve.Net Blue Power Panel, Color Control Panel, Smartphone or Tablet (Bluetooth Smart), Laptop or Computer (USB or RS232).Monitoring and control from a distanceVictron Ethernet Remote, Victron Global Remote and the Color Control Panel enable remote maintenance and remote monitoring of the MultiPlus. System data can also be saved and viewed free of charge on the VRM (Victron Remote Management) website.Remote configurationIf systems with a Color Control Panel are connected to the Ethernet, they can be accessed and settings can be changed remotely.Scope of delivery:1x Victron QUA123020010 Quattro 12/3000/120-50/50 device combination consisting of 12V 2400W sine wave converter + 12V 120A battery charger + 2 AC inputs with integrated 50A transfer switches1x instruction manual

This control panel from Victron Energy (MPN REC040010210R) is used to remotely control all Phoenix VE.Direct inverters. The built-in control panel has an on/off switch and an indicator light. The connection to the inverter is made via a 2-wire control cable (not included). Features Compatible with all Phoenix inverters with VE.Direct interfaceSimple installationWeight: 0.04 kgDimensions: 60 x 65 x 33 mm Scope of delivery: 1x Victron Phoenix Inverter control panel REC040010210R

Victron Phoenix - High-quality inverter technology guarantees you pure sine wave Inverters are used in particular where electrical systems require alternating voltage or alternating current for their operation, but only a direct voltage source is available as a power supplier (e.g. car battery). The sophisticated inverter technology of the Victron Phoenix inverter converts any 12V DC voltage into an average 230V sine wave voltage (AC voltage of 50 Hertz). The convenient inverter provides you with a power range between 150 watts and 3000 watts per module. Enjoy the solid output power of this electrotechnical device with an extremely high efficiency of up to 99 percent. Exceptional safety with a high switch-on potential Our Victron Phoenix inverter works completely fault-free even in the event of spontaneous short circuits. The device is also reliably protected against overheating (e.g. due to overloading). A high switch-on power ensures, among other things, the reliable operation of all halogen headlights on your vehicle. The smart combination of high-frequency and mains frequency technology also offers you the best possible conditions for any demanding electrotechnical application. If you are interested in our exclusive inverter technology, you can purchase the competitively priced inverter "Victron Phoenix" in our online store.

The Victron Phoenix 12/375 VE.Direct (MPN PIN121371200) is a compact pure sine wave inverter with 300W continuous output. It converts 12V DC from your battery into 230V AC power with a pure sine wave and uncompromising power quality, making it ideal for sensitive electronic devices. The Phoenix boasts excellent efficiency and is one of the best in its class thanks to its ECO mode. Using the VE.Direct communication port and optional accessories, you can connect the device to a computer or smartphone to freely program system parameters, such as low battery shutoff and restart voltages. Additional configuration options include output frequency, output voltage, and a two-pole alarm contact, among other features. The performance of the Phoenix VE.Direct series 250-500 is currently unmatched on the market at its price point, exceeding the capabilities of other devices in the same power class. Technical Features of the Phoenix 12/375 VE.Direct 300 watts of continuous power at 230V 50Hz sine waveCompatible with all standard 12V batteriesDelivers 230V AC power with pure sine wave for excellent power qualityFully programmable on/off voltage thresholdsAdjustable output voltage range from 210 to 245V Technical Highlights of the Phoenix VE.Direct Series 250VA – 500VA VE.Direct port allows connection to a computer (requires VE.Direct to USB interface cable) or smartphone, where you can monitor the device status using the free Victron app (requires VE.Direct Bluetooth Smart Dongle).Fully programmable parameters: thresholds for triggering and resetting alarms due to low battery charge + thresholds for shutting down and restarting at low battery voltage levels + output voltage (210-245V) + frequency (50Hz or 60Hz) + ECO mode on/off thresholds and ECO mode sensor.Integrated ECO mode: In ECO mode, the inverter switches to standby when the load drops below a preset value. In standby mode, the inverter briefly turns on at intervals (default: every 2.5 seconds). If the load exceeds a preset threshold during this time, the inverter remains on. Proven Reliability: The full bridge design with toroidal transformer topology has been proven over years of use. The inverters are short-circuit proof and protected against overheating (caused by overload or ambient temperature).High start-up power: Essential for starting loads such as voltage converters for LED lamps, halogen lamps, or power tools.Remote on/off switch: A remote on/off switch can be connected using a two-pole connector or between the battery's positive terminal and the left contact of the two-pole connector. Scope of Delivery:1x Victron PIN121371200 Phoenix 12/375 12V to 230V 300W 50Hz 60Hz

Phoenix Smart IP43 chargers - adaptable to different battery types Phoenix Smart IP43 chargers stand for intelligent charging with innovative technology. The charger can be set up, monitored and, if necessary, updated via a Bluetooth interface using a smartphone, tablet, etc. Intelligent charging algorithms The Victron Phoenix Smart automatically adjusts to the battery. It charges lithium (LiFePo4), AGM, gel and classic lead-acid batteries, such as those used in car batteries. The battery management system selects the appropriate charging level depending on how the battery is used. The storage mode protects the battery. It is activated automatically after 24 hours in standby mode. This maintenance during idle mode reduces the ageing of the battery to a minimum. Always the right amount of charge If the battery is only slightly discharged, overcharging is reliably prevented. Even deeply discharged batteries can be fully recharged (reconditioning for lead batteries). Like the ancient legendary figure, the modern smart Phoenix IP43 stands for many life cycles and even resurrection. Robust and environmentally friendly The IP43 protection class guarantees effective protection against solid foreign bodies and falling water spray. Phoenix Smart is therefore also suitable for outdoor use on boats and motorhomes. Thanks to its efficient use of energy with a high efficiency of 92 to 94 percent, Phoenix Smart IP43 is extremely economical.

Victron Phoenix - High-quality inverter technology guarantees you pure sine wave Inverters are used in particular where electrical systems require alternating voltage or alternating current for their operation, but only a direct voltage source is available as a power supplier (e.g. car battery). The sophisticated inverter technology of the Victron Phoenix inverter converts any 12V DC voltage into an average 230V sine wave voltage (AC voltage of 50 Hertz). The convenient inverter provides you with a power range between 150 watts and 3000 watts per module. Enjoy the solid output power of this electrotechnical device with an extremely high efficiency of up to 99 percent. Exceptional safety with a high switch-on potential Our Victron Phoenix inverter works completely fault-free even in the event of spontaneous short circuits. The device is also reliably protected against overheating (e.g. due to overloading). A high switch-on power ensures, among other things, the reliable operation of all halogen headlights on your vehicle. The smart combination of high-frequency and mains frequency technology also offers you the best possible conditions for any demanding electrotechnical application. If you are interested in our exclusive inverter technology, you can purchase the competitively priced inverter "Victron Phoenix" in our online store.

Phoenix Smart IP43 chargers - adaptable to different battery types Phoenix Smart IP43 chargers stand for intelligent charging with innovative technology. The charger can be set up, monitored and, if necessary, updated via a Bluetooth interface using a smartphone, tablet, etc. Intelligent charging algorithms The Victron Phoenix Smart automatically adjusts to the battery. It charges lithium (LiFePo4), AGM, gel and classic lead-acid batteries, such as those used in car batteries. The battery management system selects the appropriate charging level depending on how the battery is used. The storage mode protects the battery. It is activated automatically after 24 hours in standby mode. This maintenance during idle mode reduces the ageing of the battery to a minimum. Always the right amount of charge If the battery is only slightly discharged, overcharging is reliably prevented. Even deeply discharged batteries can be fully recharged (reconditioning for lead batteries). Like the ancient legendary figure, the modern smart Phoenix IP43 stands for many life cycles and even resurrection. Robust and environmentally friendly The IP43 protection class guarantees effective protection against solid foreign bodies and falling water spray. Phoenix Smart is therefore also suitable for outdoor use on boats and motorhomes. Thanks to its efficient use of energy with a high efficiency of 92 to 94 percent, Phoenix Smart IP43 is extremely economical.

Victron Phoenix - High-quality inverter technology guarantees you pure sine wave Inverters are used in particular where electrical systems require alternating voltage or alternating current for their operation, but only a direct voltage source is available as a power supplier (e.g. car battery). The sophisticated inverter technology of the Victron Phoenix inverter converts any 12V DC voltage into an average 230V sine wave voltage (AC voltage of 50 Hertz). The convenient inverter provides you with a power range between 150 watts and 3000 watts per module. Enjoy the solid output power of this electrotechnical device with an extremely high efficiency of up to 99 percent. Exceptional safety with a high switch-on potential Our Victron Phoenix inverter works completely fault-free even in the event of spontaneous short circuits. The device is also reliably protected against overheating (e.g. due to overloading). A high switch-on power ensures, among other things, the reliable operation of all halogen headlights on your vehicle. The smart combination of high-frequency and mains frequency technology also offers you the best possible conditions for any demanding electrotechnical application. If you are interested in our exclusive inverter technology, you can purchase the competitively priced inverter "Victron Phoenix" in our online store.

Victron Phoenix - High-quality inverter technology guarantees you pure sine wave Inverters are used in particular where electrical systems require alternating voltage or alternating current for their operation, but only a direct voltage source is available as a power supplier (e.g. car battery). The sophisticated inverter technology of the Victron Phoenix inverter converts any 12V DC voltage into an average 230V sine wave voltage (AC voltage of 50 Hertz). The convenient inverter provides you with a power range between 150 watts and 3000 watts per module. Enjoy the solid output power of this electrotechnical device with an extremely high efficiency of up to 99 percent. Exceptional safety with a high switch-on potential Our Victron Phoenix inverter works completely fault-free even in the event of spontaneous short circuits. The device is also reliably protected against overheating (e.g. due to overloading). A high switch-on power ensures, among other things, the reliable operation of all halogen headlights on your vehicle. The smart combination of high-frequency and mains frequency technology also offers you the best possible conditions for any demanding electrotechnical application. If you are interested in our exclusive inverter technology, you can purchase the competitively priced inverter "Victron Phoenix" in our online store.

Victron Phoenix - High-quality inverter technology guarantees you pure sine wave Inverters are used in particular where electrical systems require alternating voltage or alternating current for their operation, but only a direct voltage source is available as a power supplier (e.g. car battery). The sophisticated inverter technology of the Victron Phoenix inverter converts any 12V DC voltage into an average 230V sine wave voltage (AC voltage of 50 Hertz). The convenient inverter provides you with a power range between 150 watts and 3000 watts per module. Enjoy the solid output power of this electrotechnical device with an extremely high efficiency of up to 99 percent. Exceptional safety with a high switch-on potential Our Victron Phoenix inverter works completely fault-free even in the event of spontaneous short circuits. The device is also reliably protected against overheating (e.g. due to overloading). A high switch-on power ensures, among other things, the reliable operation of all halogen headlights on your vehicle. The smart combination of high-frequency and mains frequency technology also offers you the best possible conditions for any demanding electrotechnical application. If you are interested in our exclusive inverter technology, you can purchase the competitively priced inverter "Victron Phoenix" in our online store.

The Phoenix 48/5000 Smart Inverter from Victron Energy Victron Energy (MPN PIN482500000) is an advanced inverter based on the proven Phoenix series. It offers a continuous output of 5000W and is designed for 48V battery voltage. Compared to the previous models, the Phoenix Smart series has a Bluetooth module and a VE.Direct output for wireless remote monitoring and system configuration. The Phoenix 48/5000 Smart is also characterized by its high switch-on performance and reliability and, thanks to the integrated ECO mode, also plays in the top league of this device class in terms of self-consumption and efficiency. Phoenix 48/5000 Smart performance features for 48V battery voltage, output voltage 230 VAC ±2% Output power (non-linear): 5000W, 4000W linear continuous load at 25 degrees ambient temperature 10000W peak power to cope with high starting currents integrated Bluetooth module and VE.Direct port for wireless monitoring and system integration Designed for high inrush currents integrated alarm relay, ECO mode Monitoring of input and output voltage, load and alarms etc. via Bluetooth or VE.Direct Integrated, two-pole plug for connecting an on/off switch (remote control) Parameters configurable via Bluetooth or VE.Direct Low battery voltage alarm Threshold values for switching off and restarting at low battery voltage values Dynamic switch-off: load-dependent switch-off threshold value Output voltage: 230 VAC ±2%, frequency: 50 Hz or 60 Hz Threshold value for ECO mode on/off and ECO mode sensor Alarm relay High reliability thanks to toroidal transformer topologyComplete bridging with an additional toroidal transformer topology has proven itself over many years. The inverters are short-circuit-proof and protected against overheating (whether caused by overload or ambient temperature). Very high switch-on powerThis is required for switching on loads such as voltage converters for LED lamps, halogen lamps or power tools. Eco modeIn ECO mode, the inverter switches to standby as soon as the load falls below a preset value. In standby mode, the inverter then switches on every 2.5 seconds for a short period of time (adjustable). If the load exceeds the preset threshold value, the inverter remains switched on. Remote-controlled on/off switchingA remote-controlled on/off switch or a relay contact can be connected to the two-pole plug. Alternatively, connection H (left) of the two-pin plug can be connected to a positive battery terminal or connection L (right) of the two-pin plug can be connected to the negative battery terminal (or to the body of a vehicle, for example). Scope of delivery: 1x Victron PIN482500000 Phoenix Smart 48/50001x operating instructions

Victron Phoenix - High-quality inverter technology guarantees you pure sine wave Inverters are used in particular where electrical systems require alternating voltage or alternating current for their operation, but only a direct voltage source is available as a power supplier (e.g. car battery). The sophisticated inverter technology of the Victron Phoenix inverter converts any 12V DC voltage into an average 230V sine wave voltage (AC voltage of 50 Hertz). The convenient inverter provides you with a power range between 150 watts and 3000 watts per module. Enjoy the solid output power of this electrotechnical device with an extremely high efficiency of up to 99 percent. Exceptional safety with a high switch-on potential Our Victron Phoenix inverter works completely fault-free even in the event of spontaneous short circuits. The device is also reliably protected against overheating (e.g. due to overloading). A high switch-on power ensures, among other things, the reliable operation of all halogen headlights on your vehicle. The smart combination of high-frequency and mains frequency technology also offers you the best possible conditions for any demanding electrotechnical application. If you are interested in our exclusive inverter technology, you can purchase the competitively priced inverter "Victron Phoenix" in our online store.

Victron Phoenix - High-quality inverter technology guarantees you pure sine wave Inverters are used in particular where electrical systems require alternating voltage or alternating current for their operation, but only a direct voltage source is available as a power supplier (e.g. car battery). The sophisticated inverter technology of the Victron Phoenix inverter converts any 12V DC voltage into an average 230V sine wave voltage (AC voltage of 50 Hertz). The convenient inverter provides you with a power range between 150 watts and 3000 watts per module. Enjoy the solid output power of this electrotechnical device with an extremely high efficiency of up to 99 percent. Exceptional safety with a high switch-on potential Our Victron Phoenix inverter works completely fault-free even in the event of spontaneous short circuits. The device is also reliably protected against overheating (e.g. due to overloading). A high switch-on power ensures, among other things, the reliable operation of all halogen headlights on your vehicle. The smart combination of high-frequency and mains frequency technology also offers you the best possible conditions for any demanding electrotechnical application. If you are interested in our exclusive inverter technology, you can purchase the competitively priced inverter "Victron Phoenix" in our online store.

Der Victron Phoenix 12/500VE.Direct (MPN PIN121501100) ist ein kleiner Sinuswechselrichter mit 400W Dauerleistung. Das Gerät wandelt 12V Gleichspannung aus Ihrer Batterie in 230V AC Wechselstrom um und das mit einer reinen Sinusspannung und kompromissloser Strom-Qualität, die auch für empfindliche Elektronik-Produkte bestens geeignet ist. Der Wirkungsgrad des Phoenix ist hervorragend und dank des ECO-Mode einer der höchsten seiner Klasse. Über den VE.Direct Kommunikationsanschluss können Sie mit optionalen Zubehör, das Gerät mit einem Computer oder dem Smartphone verbinden und einige Systemparameter wie die Ausschaltspannung und Wiedereinschaltspannung bei leerem Akku völlig frei programmieren! Viele weitere Konfigurationsmöglichkeiten wie Ausgangsfrequenz und Ausgangsspannung sowie ein 2-poliger Alarm-Kontakt gehören zu den Leistungsmerkmalen dieses Spannungs-Umformers.Der Leistungsumfang der Phoenix-Serie VE.Direct 250-500 ist für den Preis im Moment einmalig am Markt und geht weit über die Fähigkeiten anderer Geräte der gleichen Leistungsklassen hinaus.technische Merkmale des Phoenix 12/375 VE.Direct 400 Watt Dauerstrom-Leistung bei 230V 50Hz Sinusspannungfür alle gängigen 12V Batterien geeignet230V AC Strom mit reiner Sinuswelle liefert eine perfekte  Stromqualitätfrei programmierbare Ein- und Ausschaltschwellenfrei einstellbare Ausgangsspannung im Bereich von 210 – 245V technische Highlights der Phoenix VE.Direct Serie 250VA – 500VA VE.Direct-Anschluss ermöglicht die Verbindung des Stromwandlers mit einen Computer (VE.Direct zu USB-Interface Kabel benötigt) oder Ihrem Smartphone auf dem Sie mit der kostenlosen Victron App den Status Ihres Gerätes immer im Auge behalten (VE.Direct Bluetooth Smart Dongle erforderlich).Vollständig programmierbare Parameter: Schwellwerte zum Auslösen und Zurücksetzen von Alarmen bei niedrigem Ladezustand der Batterie + Schwellwerte zum Ausschalten und Neustarten bei niedrigen Batteriespannungswerten + Ausgangsspannung 210 - 245V  + Schwellwerte zum Ausschalten und Neustarten bei niedrigen Batteriespannungswerten + Frequenz 50 Hz oder 60 Hz + Schwellwert für ECO-Modus ein/aus und ECO-Modus-Fu¨hlerECO-Modus integriert: Im ECO-Modus schaltet der Wechselrichter auf Standby, sobald die Last unter einen voreingestellten Wert abfällt. Im Standby-Modus schaltet sich der Wechselrichter dann für einen kurzen Zeitraum ein (regulierbare Standardeinstellung: alle 2,5 Sekunden). Überschreitet dabei die Last einen voreingestellten Schwellwert, bleibt der Wechselrichter eingeschaltet. Bewährte Zuverlässigkeit des Stromumwandlers: Die vollständige Überbrückung zusätzlich mit einer Ringtransformatorentopologie hat sich seit Jahren bewährt. Die Wechselrichter sind kurzschlussfest und vor Überhitzung (ob nun durch Überlastung oder durch die Umgebungstemperatur hervorgerufen) geschützt.Hohe Einschaltleistung: Diese wird zum Einschalten von Lasten wie zum Beispiel Spannungsumformern für LED-Lampen, Halogenlampen oder Elektrowerkzeugen benötigt.Ferngesteuerte Ein-/Aus-Schaltung möglich: Ein ferngesteuerter Ein-/Aus-Schalter lässt sich mit einem zweipoligen Stecker oder zwischen den Pluspol der Batterie und dem linken Kontakt des zweipoligen Steckers anschließen.Lieferumfang:1x Victron PIN121501100 Phoenix 12/500 12V auf 230V 400W 50Hz 60Hz

Victron Phoenix - High-quality inverter technology guarantees you pure sine wave Inverters are used in particular where electrical systems require alternating voltage or alternating current for their operation, but only a direct voltage source is available as a power supplier (e.g. car battery). The sophisticated inverter technology of the Victron Phoenix inverter converts any 12V DC voltage into an average 230V sine wave voltage (AC voltage of 50 Hertz). The convenient inverter provides you with a power range between 150 watts and 3000 watts per module. Enjoy the solid output power of this electrotechnical device with an extremely high efficiency of up to 99 percent. Exceptional safety with a high switch-on potential Our Victron Phoenix inverter works completely fault-free even in the event of spontaneous short circuits. The device is also reliably protected against overheating (e.g. due to overloading). A high switch-on power ensures, among other things, the reliable operation of all halogen headlights on your vehicle. The smart combination of high-frequency and mains frequency technology also offers you the best possible conditions for any demanding electrotechnical application. If you are interested in our exclusive inverter technology, you can purchase the competitively priced inverter "Victron Phoenix" in our online store.

Victron Phoenix - High-quality inverter technology guarantees you pure sine wave Inverters are used in particular where electrical systems require alternating voltage or alternating current for their operation, but only a direct voltage source is available as a power supplier (e.g. car battery). The sophisticated inverter technology of the Victron Phoenix inverter converts any 12V DC voltage into an average 230V sine wave voltage (AC voltage of 50 Hertz). The convenient inverter provides you with a power range between 150 watts and 3000 watts per module. Enjoy the solid output power of this electrotechnical device with an extremely high efficiency of up to 99 percent. Exceptional safety with a high switch-on potential Our Victron Phoenix inverter works completely fault-free even in the event of spontaneous short circuits. The device is also reliably protected against overheating (e.g. due to overloading). A high switch-on power ensures, among other things, the reliable operation of all halogen headlights on your vehicle. The smart combination of high-frequency and mains frequency technology also offers you the best possible conditions for any demanding electrotechnical application. If you are interested in our exclusive inverter technology, you can purchase the competitively priced inverter "Victron Phoenix" in our online store.

Victron Phoenix - High-quality inverter technology guarantees you pure sine wave Inverters are used in particular where electrical systems require alternating voltage or alternating current for their operation, but only a direct voltage source is available as a power supplier (e.g. car battery). The sophisticated inverter technology of the Victron Phoenix inverter converts any 12V DC voltage into an average 230V sine wave voltage (AC voltage of 50 Hertz). The convenient inverter provides you with a power range between 150 watts and 3000 watts per module. Enjoy the solid output power of this electrotechnical device with an extremely high efficiency of up to 99 percent. Exceptional safety with a high switch-on potential Our Victron Phoenix inverter works completely fault-free even in the event of spontaneous short circuits. The device is also reliably protected against overheating (e.g. due to overloading). A high switch-on power ensures, among other things, the reliable operation of all halogen headlights on your vehicle. The smart combination of high-frequency and mains frequency technology also offers you the best possible conditions for any demanding electrotechnical application. If you are interested in our exclusive inverter technology, you can purchase the competitively priced inverter "Victron Phoenix" in our online store.