Phoenix Smart IP43 chargers - adaptable to different battery types Phoenix Smart IP43 chargers stand for intelligent charging with innovative technology. The charger can be set up, monitored and, if necessary, updated via a Bluetooth interface using a smartphone, tablet, etc. Intelligent charging algorithms The Victron Phoenix Smart automatically adjusts to the battery. It charges lithium (LiFePo4), AGM, gel and classic lead-acid batteries, such as those used in car batteries. The battery management system selects the appropriate charging level depending on how the battery is used. The storage mode protects the battery. It is activated automatically after 24 hours in standby mode. This maintenance during idle mode reduces the ageing of the battery to a minimum. Always the right amount of charge If the battery is only slightly discharged, overcharging is reliably prevented. Even deeply discharged batteries can be fully recharged (reconditioning for lead batteries). Like the ancient legendary figure, the modern smart Phoenix IP43 stands for many life cycles and even resurrection. Robust and environmentally friendly The IP43 protection class guarantees effective protection against solid foreign bodies and falling water spray. Phoenix Smart is therefore also suitable for outdoor use on boats and motorhomes. Thanks to its efficient use of energy with a high efficiency of 92 to 94 percent, Phoenix Smart IP43 is extremely economical.

Phoenix Smart IP43 chargers - adaptable to different battery types Phoenix Smart IP43 chargers stand for intelligent charging with innovative technology. The charger can be set up, monitored and, if necessary, updated via a Bluetooth interface using a smartphone, tablet, etc. Intelligent charging algorithms The Victron Phoenix Smart automatically adjusts to the battery. It charges lithium (LiFePo4), AGM, gel and classic lead-acid batteries, such as those used in car batteries. The battery management system selects the appropriate charging level depending on how the battery is used. The storage mode protects the battery. It is activated automatically after 24 hours in standby mode. This maintenance during idle mode reduces the ageing of the battery to a minimum. Always the right amount of charge If the battery is only slightly discharged, overcharging is reliably prevented. Even deeply discharged batteries can be fully recharged (reconditioning for lead batteries). Like the ancient legendary figure, the modern smart Phoenix IP43 stands for many life cycles and even resurrection. Robust and environmentally friendly The IP43 protection class guarantees effective protection against solid foreign bodies and falling water spray. Phoenix Smart is therefore also suitable for outdoor use on boats and motorhomes. Thanks to its efficient use of energy with a high efficiency of 92 to 94 percent, Phoenix Smart IP43 is extremely economical.

Phoenix Smart IP43 chargers - adaptable to different battery types Phoenix Smart IP43 chargers stand for intelligent charging with innovative technology. The charger can be set up, monitored and, if necessary, updated via a Bluetooth interface using a smartphone, tablet, etc. Intelligent charging algorithms The Victron Phoenix Smart automatically adjusts to the battery. It charges lithium (LiFePo4), AGM, gel and classic lead-acid batteries, such as those used in car batteries. The battery management system selects the appropriate charging level depending on how the battery is used. The storage mode protects the battery. It is activated automatically after 24 hours in standby mode. This maintenance during idle mode reduces the ageing of the battery to a minimum. Always the right amount of charge If the battery is only slightly discharged, overcharging is reliably prevented. Even deeply discharged batteries can be fully recharged (reconditioning for lead batteries). Like the ancient legendary figure, the modern smart Phoenix IP43 stands for many life cycles and even resurrection. Robust and environmentally friendly The IP43 protection class guarantees effective protection against solid foreign bodies and falling water spray. Phoenix Smart is therefore also suitable for outdoor use on boats and motorhomes. Thanks to its efficient use of energy with a high efficiency of 92 to 94 percent, Phoenix Smart IP43 is extremely economical.

The Automatic-Charger Pb 1230 SMT 2B from Votronic (MPN 3114) is a modern battery charger for mobile use. It has charging programs for GEL, AGM, acid and modern lithium batteries and is designed for 12V battery voltage. The charging current at the main output is 30A. There is also a secondary charging output for the starter battery, which can supply an additional 2A charging current. The device is suitable for batteries with a capacity of 120 Ah - 230 Ah.Important features of the Pb 1230 SMT 2B battery charger reliably charges GEL, AGM, acid and LiFePO4 batteries 30A charging current, 2A charging current at the auxiliary charging output Official Votronic part number: 3114 Battery capacity (recommended): 120 Ah - 230 Ah Charging options: 1 supply battery and 1 starter battery The charging voltage is free of peaks and regulated in such a way that overcharging of the batteries is prevented. Fully automatic continuous operation: The charger can be permanently connected to the battery and keeps it fully charged. In the event of a power failure, the batteries are not discharged (disconnection by safety switch). Lithium LiFePO4 maintenance, auto wake-up, maintenance phase: Regular automatic activation of battery cell balancing every 10 days to ensure that the battery is always fully charged. Lead battery regeneration twice a week during long downtimes to prevent harmful acid stratification. Parallel and buffer operation: The battery continues to be charged or kept fully charged during simultaneous consumption. The charger automatically calculates and monitors the adjustment of the charging times. Monitoring-free charging: Multiple protection against overload, overheating, overvoltage, short circuit, polarity reversal, malfunction and battery back-discharge through electronic cut-off up to complete disconnection of charger and battery by built-in safety switches. Connection for battery temperature sensor (accessory temperature sensor 825, art. no. 2001): With lead batteries (acid, gel, AGM), the charging voltage is automatically adjusted to the battery temperature, resulting in a better full charge of the weaker battery in cold weather and avoiding unnecessary battery gassing and thus battery stress in summer temperatures. With LiFePO4 batteries, the battery temperature sensor is required for the function: It serves to protect the battery at high and especially at low temperatures below 0°C. Silent Run function: Noise-optimized operation at the touch of a button (night mode). Power supply unit function: Enables consumers to be supplied without a battery (e.g. battery replacement). Charging cable compensation: Voltage losses on the charging cables are automatically compensated for. Built-in on-board mains filter: Problem-free parallel operation with solar systems, wind and petrol generators, alternators etc. on one battery. Charging aid for deeply discharged lead batteries: Gentle pre-charging of the (lead-acid, -gel, -AGM) battery up to 8 V, then powerful support for the battery if consumers are still switched on. Disconnection of the batteries in the event of mains failure, overheating, malfunction (safety switch per charging output). Separate auxiliary charging output "S" for supporting and trickle charging the vehicle starter battery. Overview of the charging programs of the Pb 1230 SMT 2B"Gel": Charging program for gel batteries, characteristic curve IU1oU2oU3 Adapted to sealed, gas-tight gel/dryfit batteries with fixed electrolyte, which generally require a higher charging voltage level and longer U1 holding times in order to achieve short charging times with particularly high capacity storage and to avoid long-term battery "starvation"."AGM": Charging program for AGM/fleece batteries, characteristic curve IU1oU2oU3 Intended for charging sealed, gas-tight AGM (Absorbent Glass Mat) batteries in lead-fleece technology, which require a particularly high U1 level with coordinated holding times for full charging and then a moderate U2 level for charge retention (plate and round cell technology). ."UNIVERSAL": Charging program for lead-acid/wet/AGM batteries, characteristic curve IU1oU2oU3 Universal program for charging and charge retention of acid batteries in vehicles (mixed mobile/stationary). With a medium U1 level, still offers short charging times, a good charge factor and good acid mixing for open and closed, low-maintenance, maintenance-free standard, traction, lighting, solar and heavy-duty batteries, as well as AGM batteries with a normal U1 level."LiFePO4": Charging program for lithium batteries, characteristic curve IU1oU2oU3 Charging program tailored to lithium LiFePO4 batteries with their own BMS and prescribed or built-in protective circuitry. A special rest maintenance function automatically keeps the LiFePO4 battery at a charge level of 50-80% when the vehicle is parked (seasonal operation), which is beneficial for the service life, and also buffers 12 V consumers and the vehicle starter battery. In addition, a regular Auto Wake UP function activates the battery cell balancing.Scope of delivery:1X Votronic 3114 Pb 1230 SMT 2B battery charger1x operating instructions (German)

The Automatic-Charger Pb 2416 SMT 2B from Votronic (MPN 6232) is a modern battery charger for mobile use. It has charging programs for GEL, AGM, acid and modern lithium batteries and is designed for 24V battery voltage. The charging current at the main output is 16A. There is also a secondary charging output for the starter battery, which can supply an additional 2A charging current. The device is suitable for batteries with a capacity of 40 Ah - 200 Ah.Important features of the Pb 2416 SMT 2B battery charger reliably charges GEL, AGM, acid and LiFePO4 batteries 16A charging current, 4A charging current at the auxiliary charging output Official Votronic part number: 6232 Battery capacity (recommended): 40 Ah - 200 Ah Charging options: The Pb 2416 SMT 2B charges: 1 supply battery and 1 starter battery. The charging voltage is free of peaks and regulated in such a way that overcharging of the batteries is prevented. Fully automatic continuous operation: The charger can be permanently connected to the battery and keeps it fully charged. In the event of a power failure, the batteries are not discharged (disconnection by safety switch). Lithium LiFePO4 maintenance, auto wake-up, maintenance phase: Regular automatic activation of battery cell balancing every 10 days to ensure that the battery is always fully charged. Lead battery regeneration twice a week during long downtimes to prevent harmful acid stratification. Parallel and buffer operation: The battery continues to be charged or kept fully charged during simultaneous consumption. The charger automatically calculates and monitors the adjustment of the charging times. Monitoring-free charging: Multiple protection against overload, overheating, overvoltage, short circuit, polarity reversal, malfunction and battery reverse discharge through electronic cut-off up to complete disconnection of charger and battery by built-in safety switches. Connection for battery temperature sensor (accessory temperature sensor 825, art. no. 2001): With lead batteries (acid, gel, AGM), the charging voltage is automatically adjusted to the battery temperature, resulting in a better full charge of the weaker battery in cold weather and avoiding unnecessary battery gassing and thus battery stress in summer temperatures. With LiFePO4 batteries, the battery temperature sensor is required for the function: It serves to protect the battery at high and especially at low temperatures below 0°C. Silent Run function: Noise-optimized operation at the touch of a button (night mode). Power supply unit function: Enables consumers to be supplied without a battery (e.g. battery replacement). Charging cable compensation: Voltage losses on the charging cables are automatically compensated for. Built-in on-board mains filter: Problem-free parallel operation with solar systems, wind and petrol generators, alternators etc. on one battery. Charging aid for deeply discharged lead batteries: Gentle pre-charging of the (lead-acid, -gel, -AGM) battery up to 8 V, then powerful support for the battery if consumers are still switched on. Disconnection of the batteries in the event of mains failure, overheating, malfunction (safety switch per charging output). Separate auxiliary charging output "S" for supporting and trickle charging the vehicle starter battery. Charging current distributor optionally switchable to separate charging program for starter battery Starter battery is also charged with full charging current if required (short vehicle service life) Battery capacity adjustable in 4 stages (12 charging programs in total) Inputs for voltage sensor (sense) cables, can optionally be used with extra-long charging cables and/or external, lossy diode charging current distributors Mains/charging power can be reduced in the event of low-power or limited mains supply, e.g. weakly fused shore power supply, generator operation etc. (power limit function) Overview of the charging programs of the Pb 2416 SMT 2B"Gel": Charging program for gel batteries, characteristic curve IU1oU2oU3, matched to sealed, gas-tight gel/dryfit batteries with fixed electrolyte, which generally require a higher charging voltage level and longer U1 holding times in order to achieve short charging times with particularly high capacity storage and to avoid long-term battery "starvation"."AGM": Charging program for AGM/fleece batteries, characteristic curve IU1oU2oU3 Intended for charging sealed, gas-tight AGM (Absorbent Glass Mat) batteries in lead-fleece technology, which require a particularly high U1 level with coordinated holding times for full charging and then a moderate U2 level for charge retention (plate and round cell technology). ."UNIVERSAL": Charging program for lead-acid/wet/AGM batteries, characteristic curve IU1oU2oU3 Universal program for charging and charge retention of acid batteries in vehicles (mixed mobile/stationary). With a medium U1 level, still offers short charging times, a good charging factor and good acid mixing for open and closed, low-maintenance, maintenance-free standard, traction, lighting, solar and heavy-duty batteries, as well as AGM batteries with a normal U1 level. "LiFePO4": Charging program for lithium batteries, characteristic curve IU1oU2oU3? charging program tailored to lithium LiFePO4 batteries with their own BMS and prescribed or built-in protective circuitry. A special rest maintenance function automatically keeps the LiFePO4 battery at a charge level of 50-80% when the vehicle is switched off (seasonal operation), which is beneficial for its service life, and also buffers 12 V consumers and the vehicle starter battery. In addition, a regular Auto Wake UP function activates the battery cell balancing.Scope of delivery:1X Votronic 6232 Pb 2416 SMT 2B battery charger1x operating instructions (German)

The Automatic-Charger Pb 1280 SMT 2B from Votronic (MPN 3131) is a modern battery charger for mobile use. It has charging programs for GEL, AGM and lead-acid batteries and is designed for 12V battery voltage. The charging current at the main output is 80A. There is also a secondary charging output for the starter battery, which can supply an additional 2A charging current. The device is suitable for batteries with a capacity of 150 Ah - 880 Ah.Important features of the Pb 1280 SMT 2B battery charger reliably charges GEL, AGM and lead-acid batteries 80A charging current, 4A charging current at the auxiliary charging output Official Votronic part number: 3131 Battery capacity (recommended): 150 Ah - 880 Ah Charging options: The Pb 1280 SMT 2B charges: one supply battery and one starter battery. Excellent charging technology The charging voltages are free of peaks and regulated to prevent overcharging Fully automatic continuous operation for constant operational readiness of the batteries Precise battery temperature compensation (temperature sensor art. no. 2001 required) Separate auxiliary charging output "S" for support and trickle charging of the vehicle starter battery, max. 2A Automatic battery regeneration during long downtimes (twice a week) Compensation of voltage losses on the charging cables for exact compliance with the charging voltages Intelligent microprocessor control takes into account the simultaneous supply of consumers to the battery Disconnection of the batteries in the event of mains failure, overheating, malfunction (safety switch per charging output) Silent-run function adjustable (night setback) Battery capacity adjustable in 4 stages (12 charging programs in total) Inputs for voltage sensor (sense) cables, optionally usable with extra-long charging cables and/or external, lossy diode charging current distributors Mains/charging power can be reduced for low-power or limited mains supply, e.g. weakly fused shore power supply, generator operation, etc. (power limit function) Overview of the charging programs of the Pb 1280 SMT 2B"Gel": Charging program for gel batteries, characteristic curve IU1oU2oU3, matched to sealed, gas-tight gel/dryfit batteries with fixed electrolyte, which generally require a higher charging voltage level and longer U1 holding times in order to achieve short charging times with particularly high capacity storage and to avoid long-term battery "starvation"."AGM": Charging program for AGM/fleece batteries, characteristic curve IU1oU2oU3 Intended for charging sealed, gas-tight AGM (Absorbent Glass Mat) batteries in lead-fleece technology, which require a particularly high U1 level with coordinated holding times for full charging and then a moderate U2 level for charge retention (plate and round cell technology). ."UNIVERSAL": Charging program for lead-acid/wet/AGM batteries, characteristic curve IU1oU2oU3 Universal program for charging and charge retention of acid batteries in vehicles (mixed mobile/stationary). With a medium U1 level, still offers short charging times, a good charging factor and good acid mixing for open and closed, low-maintenance, maintenance-free standard, traction, lighting, solar and heavy-duty batteries, as well as AGM batteries with a normal U1 level.Scope of delivery:1x Votronic 3131 Pb 1280 SMT 2B battery charger1x operating instructions (German)

The Automatic-Charger Pb 1225 SMT 2B from Votronic (MPN 3102) is a modern battery charger for mobile use. It has charging programs for GEL, AGM, acid and modern lithium batteries and is designed for 12V battery voltage. The charging current at the main output is 25A. There is also a secondary charging output for the starter battery, which can supply an additional 2A charging current. The device is suitable for batteries with a capacity of 100 Ah - 180 Ah.Important features of the Pb 1225 SMT 2B battery charger reliably charges GEL, AGM, acid and LiFePO4 batteries 25A charging current, 2A charging current at the auxiliary charging output Official Votronic part number: 3102 Battery capacity (recommended): 100 Ah - 180 Ah Charging options: 1 supply battery and 1 starter battery The charging voltage is free of peaks and regulated in such a way that overcharging of the batteries is prevented. Fully automatic continuous operation: The charger can be permanently connected to the battery and keeps it fully charged. In the event of a power failure, the batteries are not discharged (disconnection by safety switch). Lithium LiFePO4 maintenance, auto wake-up, maintenance phase: Regular automatic activation of battery cell balancing every 10 days to ensure that the battery is always fully charged. Lead battery regeneration twice a week during long downtimes to prevent harmful acid stratification. Parallel and buffer operation: The battery continues to be charged or kept fully charged during simultaneous consumption. The charger automatically calculates and monitors the adjustment of the charging times. Monitoring-free charging: Multiple protection against overload, overheating, overvoltage, short circuit, polarity reversal, malfunction and battery back-discharge through electronic cut-off up to complete disconnection of charger and battery by built-in safety switches. Connection for battery temperature sensor (accessory temperature sensor 825, art. no. 2001): With lead batteries (acid, gel, AGM), the charging voltage is automatically adjusted to the battery temperature, resulting in a better full charge of the weaker battery in cold weather and avoiding unnecessary battery gassing and thus battery stress in summer temperatures. With LiFePO4 batteries, the battery temperature sensor is required for the function: It serves to protect the battery at high and especially at low temperatures below 0°C. Silent Run function: Noise-optimized operation at the touch of a button (night mode). Power supply unit function: Enables consumers to be supplied without a battery (e.g. battery replacement). Charging cable compensation: Voltage losses on the charging cables are automatically compensated for. Built-in on-board mains filter: Problem-free parallel operation with solar systems, wind and petrol generators, alternators etc. on one battery. Charging aid for deeply discharged lead batteries: Gentle pre-charging of the (lead-acid, -gel, -AGM) battery up to 8 V, then powerful support for the battery if consumers are still switched on. Disconnection of the batteries in the event of mains failure, overheating, malfunction (safety switch per charging output). Separate auxiliary charging output "S" for supporting and trickle charging the vehicle starter battery. Overview of the charging programs of the Pb 1225 SMT 2B"Gel": Charging program for gel batteries, characteristic curve IU1oU2oU3 Adapted to sealed, gas-tight gel/dryfit batteries with fixed electrolyte, which generally require a higher charging voltage level and longer U1 holding times in order to achieve short charging times with particularly high capacity storage and to avoid long-term battery "starvation"."AGM": Charging program for AGM/fleece batteries, characteristic curve IU1oU2oU3 Intended for charging sealed, gas-tight AGM (Absorbent Glass Mat) batteries in lead-fleece technology, which require a particularly high U1 level with coordinated holding times for full charging and then a moderate U2 level for charge retention (plate and round cell technology). ."UNIVERSAL": Charging program for lead-acid/wet/AGM batteries, characteristic curve IU1oU2oU3 Universal program for charging and charge retention of acid batteries in vehicles (mixed mobile/stationary). With a medium U1 level, still offers short charging times, a good charge factor and good acid mixing for open and closed, low-maintenance, maintenance-free standard, traction, lighting, solar and heavy-duty batteries, as well as AGM batteries with a normal U1 level."LiFePO4": Charging program for lithium batteries, characteristic curve IU1oU2oU3 Charging program tailored to lithium LiFePO4 batteries with their own BMS and prescribed or built-in protective circuitry. A special rest maintenance function automatically keeps the LiFePO4 battery at a charge level of 50-80% when the vehicle is parked (seasonal operation), which is beneficial for the service life, and also buffers 12 V consumers and the vehicle starter battery. In addition, a regular Auto Wake UP function activates the battery cell balancing.Scope of delivery:1X Votronic 3102 Pb 1225 SMT 2B battery charger1x operating instructions (German)

The Automatic-Charger Pb 2440 SMT 2B from Votronic (MPN 6250) is a modern battery charger for mobile use. It has charging programs for GEL, AGM, acid and modern lithium batteries and is designed for 24V battery voltage. The charging current at the main output is 40A. There is also a secondary charging output for the starter battery, which can supply an additional 2A charging current. The device is suitable for batteries with a capacity of 75 Ah - 440 Ah.Important features of the Pb 2440 SMT 2B battery charger reliably charges GEL, AGM, acid and LiFePO4 batteries 40A charging current, 4A charging current at the auxiliary charging output Official Votronic part number: 6250 Battery capacity (recommended): 75 Ah - 400 Ah Charging options: The Pb 2440 SMT 2B charges: 1 supply battery and 1 starter battery. The charging voltage is free of peaks and regulated in such a way that overcharging of the batteries is prevented. Fully automatic continuous operation: The charger can be permanently connected to the battery and keeps it fully charged. In the event of a power failure, the batteries are not discharged (disconnection by safety switch). Lithium LiFePO4 maintenance, auto wake-up, maintenance phase: Regular automatic activation of battery cell balancing every 10 days to ensure that the battery is always fully charged. Lead battery regeneration twice a week during long downtimes to prevent harmful acid stratification. Parallel and buffer operation: The battery continues to be charged or kept fully charged during simultaneous consumption. The charger automatically calculates and monitors the adjustment of the charging times. Monitoring-free charging: Multiple protection against overload, overheating, overvoltage, short circuit, polarity reversal, malfunction and battery reverse discharge through electronic cut-off up to complete disconnection of charger and battery by built-in safety switches. Connection for battery temperature sensor (accessory temperature sensor 825, art. no. 2001): With lead batteries (acid, gel, AGM), the charging voltage is automatically adjusted to the battery temperature, resulting in a better full charge of the weaker battery in cold weather and avoiding unnecessary battery gassing and thus battery stress in summer temperatures. With LiFePO4 batteries, the battery temperature sensor is required for the function: It serves to protect the battery at high and especially at low temperatures below 0°C. Silent Run function: Noise-optimized operation at the touch of a button (night mode). Power supply unit function: Enables consumers to be supplied without a battery (e.g. battery replacement). Charging cable compensation: Voltage losses on the charging cables are automatically compensated for. Built-in on-board mains filter: Problem-free parallel operation with solar systems, wind and petrol generators, alternators etc. on one battery. Charging aid for deeply discharged lead batteries: Gentle pre-charging of the (lead-acid, -gel, -AGM) battery up to 8 V, then powerful support for the battery if consumers are still switched on. Disconnection of the batteries in the event of mains failure, overheating, malfunction (safety switch per charging output). Separate auxiliary charging output "S" for supporting and trickle charging the vehicle starter battery. Charging current distributor optionally switchable to separate charging program for starter battery Starter battery is also charged with full charging current if required (short vehicle service life) Battery capacity adjustable in 4 stages (12 charging programs in total) Inputs for voltage sensor (sense) cables, can optionally be used with extra-long charging cables and/or external, lossy diode charging current distributors Mains/charging power can be reduced in the event of low-power or limited mains supply, e.g. weakly fused shore power supply, generator operation etc. (power limit function) Overview of the charging programs of the Pb 2440 SMT 2B"Gel": Charging program for gel batteries, characteristic curve IU1oU2oU3, matched to sealed, gas-tight gel/dryfit batteries with fixed electrolyte, which generally require a higher charging voltage level and longer U1 holding times in order to achieve short charging times with particularly high capacity storage and to avoid long-term battery "starvation"."AGM": Charging program for AGM/fleece batteries, characteristic curve IU1oU2oU3 Intended for charging sealed, gas-tight AGM (Absorbent Glass Mat) batteries in lead-fleece technology, which require a particularly high U1 level with coordinated holding times for full charging and then a moderate U2 level for charge retention (plate and round cell technology). ."UNIVERSAL": Charging program for lead-acid/wet/AGM batteries, characteristic curve IU1oU2oU3 Universal program for charging and charge retention of acid batteries in vehicles (mixed mobile/stationary). With a medium U1 level, still offers short charging times, a good charging factor and good acid mixing for open and closed, low-maintenance, maintenance-free standard, traction, lighting, solar and heavy-duty batteries, as well as AGM batteries with a normal U1 level. "LiFePO4": Charging program for lithium batteries, characteristic curve IU1oU2oU3? charging program tailored to lithium LiFePO4 batteries with their own BMS and prescribed or built-in protective circuitry. A special rest maintenance function automatically keeps the LiFePO4 battery at a charge level of 50-80% when the vehicle is switched off (seasonal operation), which is beneficial for its service life, and also buffers 12 V consumers and the vehicle starter battery. In addition, a regular Auto Wake UP function activates the battery cell balancing.Scope of delivery:1X Votronic 6250 Pb 2440 SMT 2B battery charger1x operating instructions (German)

The Automatic-Charger Pb 2425 SMT 3B from Votronic (MPN 6239) is a modern battery charger for mobile use. It has charging programs for GEL, AGM, acid and modern lithium batteries and is designed for 24V battery voltage. The charging current at the main output is 25A. There is also a secondary charging output for the starter battery, which can supply an additional 4A charging current. The device is suitable for batteries with a capacity of 46 Ah - 290 Ah.Important features of the Pb 2425 SMT 3B battery charger reliably charges GEL, AGM, acid and LiFePO4 batteries 25A charging current, 4A charging current at the auxiliary charging output Official Votronic part number: 6239 Battery capacity (recommended): 46 Ah - 290 Ah Charging options: The Pb 2425 SMT 3B charges: 2 supply batteries and 1 starter battery. The charging voltage is free of peaks and regulated in such a way that the batteries cannot be overcharged. Fully automatic continuous operation: The charger can be permanently connected to the battery and keeps it fully charged. In the event of a power failure, the batteries are not discharged (disconnection by safety switch). Lithium LiFePO4 maintenance, auto wake-up, maintenance phase: Regular automatic activation of battery cell balancing every 10 days to ensure that the battery is always fully charged. Lead battery regeneration twice a week during long downtimes to prevent harmful acid stratification. Parallel and buffer operation: The battery continues to be charged or kept fully charged during simultaneous consumption. The charger automatically calculates and monitors the adjustment of the charging times. Monitoring-free charging: Multiple protection against overload, overheating, overvoltage, short circuit, polarity reversal, malfunction and battery reverse discharge through electronic cut-off up to complete disconnection of charger and battery by built-in safety switches. Connection for battery temperature sensor (accessory temperature sensor 825, art. no. 2001): With lead batteries (acid, gel, AGM), the charging voltage is automatically adjusted to the battery temperature, resulting in a better full charge of the weaker battery in cold weather and avoiding unnecessary battery gassing and thus battery stress in summer temperatures. With LiFePO4 batteries, the battery temperature sensor is required for the function: It serves to protect the battery at high and especially at low temperatures below 0°C. Silent Run function: Noise-optimized operation at the touch of a button (night mode). Power supply unit function: Enables consumers to be supplied without a battery (e.g. battery replacement). Charging cable compensation: Voltage losses on the charging cables are automatically compensated for. Built-in on-board mains filter: Problem-free parallel operation with solar systems, wind and petrol generators, alternators etc. on one battery. Charging aid for deeply discharged lead batteries: Gentle pre-charging of the (lead-acid, -gel, -AGM) battery up to 8 V, then powerful support for the battery if consumers are still switched on. Disconnection of the batteries in the event of mains failure, overheating, malfunction (safety switch per charging output). Separate auxiliary charging output "S" for supporting and trickle charging the vehicle starter battery. Charging current distributor optionally switchable to separate charging program for starter battery. Starter battery is also charged with full charging current if required (short vehicle service life). Battery capacity adjustable in 4 stages (12 charging programs in total). Inputs for voltage sensor (sense) cables, optionally usable with extra-long charging cables and/or external, lossy diode charging current distributors. Mains/charging power can be reduced in the event of low-power or limited mains supply, e.g. weakly fused shore power supply, generator operation etc. (power limit function) Overview of the charging programs of the Pb 2425 SMT 3B"Gel": Charging program for gel batteries, characteristic curve IU1oU2oU3, matched to sealed, gas-tight gel/dryfit batteries with fixed electrolyte, which generally require a higher charging voltage level and longer U1 holding times in order to achieve short charging times with particularly high capacity storage and to avoid long-term battery "starvation"."AGM": Charging program for AGM/fleece batteries, characteristic curve IU1oU2oU3 Intended for charging sealed, gas-tight AGM (Absorbent Glass Mat) batteries in lead-fleece technology, which require a particularly high U1 level with coordinated holding times for full charging and then a moderate U2 level for charge retention (plate and round cell technology). ."UNIVERSAL": Charging program for lead-acid/wet/AGM batteries, characteristic curve IU1oU2oU3 Universal program for charging and charge retention of acid batteries in vehicles (mixed mobile/stationary). With a medium U1 level, still offers short charging times, a good charging factor and good acid mixing for open and closed, low-maintenance, maintenance-free standard, traction, lighting, solar and heavy-duty batteries, as well as AGM batteries with a normal U1 level. "LiFePO4": Charging program for lithium batteries, characteristic curve IU1oU2oU3? charging program tailored to lithium LiFePO4 batteries with their own BMS and prescribed or built-in protective circuitry. A special rest maintenance function automatically keeps the LiFePO4 battery at a charge level of 50-80% when the vehicle is switched off (seasonal operation), which is beneficial for its service life, and also buffers 12 V consumers and the vehicle starter battery. In addition, a regular Auto Wake UP function activates the battery cell balancing.Scope of delivery:1X Votronic 6239 Pb 2425 SMT 3B battery charger1x operating instructions (German)

The Automatic-Charger Pb 1260 SMT 3B from Votronic (MPN 3126) is a modern battery charger for mobile use. It has charging programs for GEL, AGM, acid and modern lithium batteries and is designed for 12V battery voltage. The charging current at the main output is 60A. There is also a secondary charging output for the starter battery, which can supply an additional 4A charging current. The device is suitable for batteries with a capacity of 120 Ah - 660 Ah.Important features of the Pb 1260 SMT 3B battery charger reliably charges GEL, AGM, acid and LiFePO4 batteries 60A charging current, 4A charging current at the auxiliary charging output Official Votronic part number: 3126 Battery capacity (recommended): 120 Ah - 660 Ah Charging options: The Pb 1260 SMT 3B charges: 1 to 2 supply batteries or 1 to 2 starter batteries or 1 supply and 1 starter battery. The charging voltage is free of peaks and regulated in such a way that the batteries cannot be overcharged. Fully automatic continuous operation: The charger can be permanently connected to the battery and keeps it fully charged. In the event of a power failure, the batteries are not discharged (disconnection by safety switch). Lithium LiFePO4 maintenance, auto wake-up, maintenance phase: Regular automatic activation of battery cell balancing every 10 days to ensure that the battery is always fully charged. Lead battery regeneration twice a week during long downtimes to prevent harmful acid stratification. Parallel and buffer operation: The battery continues to be charged or kept fully charged during simultaneous consumption. The charger automatically calculates and monitors the adjustment of the charging times. Monitoring-free charging: Multiple protection against overload, overheating, overvoltage, short circuit, polarity reversal, malfunction and battery reverse discharge through electronic cut-off up to complete disconnection of charger and battery by built-in safety switches. Connection for battery temperature sensor (accessory temperature sensor 825, art. no. 2001): With lead batteries (acid, gel, AGM), the charging voltage is automatically adjusted to the battery temperature, resulting in a better full charge of the weaker battery in cold weather and avoiding unnecessary battery gassing and thus battery stress in summer temperatures. With LiFePO4 batteries, the battery temperature sensor is required for the function: It serves to protect the battery at high and especially at low temperatures below 0°C. Silent Run function: Noise-optimized operation at the touch of a button (night mode). Power supply unit function: Enables consumers to be supplied without a battery (e.g. battery replacement). Charging cable compensation: Voltage losses on the charging cables are automatically compensated for. Built-in on-board mains filter: Problem-free parallel operation with solar systems, wind and petrol generators, alternators etc. on one battery. Charging aid for deeply discharged lead batteries: Gentle pre-charging of the (lead-acid, -gel, -AGM) battery up to 8 V, then powerful support for the battery if consumers are still switched on. Disconnection of the batteries in the event of mains failure, overheating, malfunction (safety switch per charging output). Separate auxiliary charging output "S" for supporting and trickle charging the vehicle starter battery. Charging current distributor optionally switchable to separate charging program for starter battery Starter battery is also charged with full charging current if required (short vehicle service life) Battery capacity adjustable in 4 stages (12 charging programs in total) Inputs for voltage sensor (sense) cables, can optionally be used with extra-long charging cables and/or external, lossy diode charging current distributors Mains/charging power can be reduced in the event of low-power or limited mains supply, e.g. weakly fused shore power supply, generator operation etc. (power limit function) Overview of the charging programs of the Pb 1260 SMT 3B"Gel": Charging program for gel batteries, characteristic curve IU1oU2oU3, matched to sealed, gas-tight gel/dryfit batteries with fixed electrolyte, which generally require a higher charging voltage level and longer U1 holding times in order to achieve short charging times with particularly high capacity storage and to avoid long-term battery "starvation"."AGM": Charging program for AGM/fleece batteries, characteristic curve IU1oU2oU3 Intended for charging sealed, gas-tight AGM (Absorbent Glass Mat) batteries in lead-fleece technology, which require a particularly high U1 level with coordinated holding times for full charging and then a moderate U2 level for charge retention (plate and round cell technology). ."UNIVERSAL": Charging program for lead-acid/wet/AGM batteries, characteristic curve IU1oU2oU3 Universal program for charging and charge retention of acid batteries in vehicles (mixed mobile/stationary). With a medium U1 level, still offers short charging times, a good charging factor and good acid mixing for open and closed, low-maintenance, maintenance-free standard, traction, lighting, solar and heavy-duty batteries, as well as AGM batteries with a normal U1 level. "LiFePO4": Charging program for lithium batteries, characteristic curve IU1oU2oU3? charging program tailored to lithium LiFePO4 batteries with their own BMS and prescribed or built-in protective circuitry. A special rest maintenance function automatically keeps the LiFePO4 battery at a charge level of 50-80% when the vehicle is switched off (seasonal operation), which is beneficial for its service life, and also buffers 12 V consumers and the vehicle starter battery. In addition, a regular Auto Wake UP function activates the battery cell balancing.Scope of delivery:1X Votronic 3126 Pb 1260 SMT 3B battery charger1x operating instructions (German)

The Automatic-Charger Pb 1240 SMT 3B from Votronic (MPN 3124) is a modern battery charger for mobile use. It has charging programs for GEL, AGM, acid and modern lithium batteries and is designed for 12V battery voltage. The charging current at the main output is 40A. There is also a secondary charging output for the starter battery, which can supply an additional 4A charging current. The device is suitable for batteries with a capacity of 75 Ah - 480 Ah.Important features of the Pb 1240 SMT 3B battery charger reliably charges GEL, AGM, acid and LiFePO4 batteries 40A charging current, 4A charging current at the auxiliary charging output Official Votronic part number: 3124 Battery capacity (recommended): 75 Ah - 480 Ah Charging options: The Pb 1240 SMT 3B charges: 1 to 2 supply batteries or 1 to 2 starter batteries or 1 supply and 1 starter battery. The charging voltage is free of peaks and regulated in such a way that the batteries cannot be overcharged. Fully automatic continuous operation: The charger can be permanently connected to the battery and keeps it fully charged. In the event of a power failure, the batteries are not discharged (disconnection by safety switch). Lithium LiFePO4 maintenance, auto wake-up, maintenance phase: Regular automatic activation of battery cell balancing every 10 days to ensure that the battery is always fully charged. Lead battery regeneration twice a week during long downtimes to prevent harmful acid stratification. Parallel and buffer operation: The battery continues to be charged or kept fully charged during simultaneous consumption. The charger automatically calculates and monitors the adjustment of the charging times. Monitoring-free charging: Multiple protection against overload, overheating, overvoltage, short circuit, polarity reversal, malfunction and battery reverse discharge through electronic cut-off up to complete disconnection of charger and battery by built-in safety switches. Connection for battery temperature sensor (accessory temperature sensor 825, art. no. 2001): With lead batteries (acid, gel, AGM), the charging voltage is automatically adjusted to the battery temperature, resulting in a better full charge of the weaker battery in cold weather and avoiding unnecessary battery gassing and thus battery stress in summer temperatures. With LiFePO4 batteries, the battery temperature sensor is required for the function: It serves to protect the battery at high and especially at low temperatures below 0°C. Silent Run function: Noise-optimized operation at the touch of a button (night mode). Power supply unit function: Enables consumers to be supplied without a battery (e.g. battery replacement). Charging cable compensation: Voltage losses on the charging cables are automatically compensated for. Built-in on-board mains filter: Problem-free parallel operation with solar systems, wind and petrol generators, alternators etc. on one battery. Charging aid for deeply discharged lead batteries: Gentle pre-charging of the (lead-acid, -gel, -AGM) battery up to 8 V, then powerful support for the battery if consumers are still switched on. Disconnection of the batteries in the event of mains failure, overheating, malfunction (safety switch per charging output). Separate auxiliary charging output "S" for supporting and trickle charging the vehicle starter battery. Charging current distributor optionally switchable to separate charging program for starter battery Starter battery is also charged with full charging current if required (short vehicle service life) Battery capacity adjustable in 4 stages (12 charging programs in total) Inputs for voltage sensor (sense) cables, can optionally be used with extra-long charging cables and/or external, lossy diode charging current distributors Mains/charging power can be reduced in the event of low-power or limited mains supply, e.g. weakly fused shore power supply, generator operation etc. (power limit function) Overview of the charging programs of the Pb 1240 SMT 3B"Gel": Charging program for gel batteries, characteristic curve IU1oU2oU3, matched to sealed, gas-tight gel/dryfit batteries with fixed electrolyte, which generally require a higher charging voltage level and longer U1 holding times in order to achieve short charging times with particularly high capacity storage and to avoid long-term battery "starvation"."AGM": Charging program for AGM/fleece batteries, characteristic curve IU1oU2oU3 Intended for charging sealed, gas-tight AGM (Absorbent Glass Mat) batteries in lead-fleece technology, which require a particularly high U1 level with coordinated holding times for full charging and then a moderate U2 level for charge retention (plate and round cell technology). ."UNIVERSAL": Charging program for lead-acid/wet/AGM batteries, characteristic curve IU1oU2oU3 Universal program for charging and charge retention of acid batteries in vehicles (mixed mobile/stationary). With a medium U1 level, still offers short charging times, a good charging factor and good acid mixing for open and closed, low-maintenance, maintenance-free standard, traction, lighting, solar and heavy-duty batteries, as well as AGM batteries with a normal U1 level. "LiFePO4": Charging program for lithium batteries, characteristic curve IU1oU2oU3? charging program tailored to lithium LiFePO4 batteries with their own BMS and prescribed or built-in protective circuitry. A special rest maintenance function automatically keeps the LiFePO4 battery at a charge level of 50-80% when the vehicle is switched off (seasonal operation), which is beneficial for its service life, and also buffers 12 V consumers and the vehicle starter battery. In addition, a regular Auto Wake UP function activates the battery cell balancing.Scope of delivery:1X Votronic 3124 Pb 1240 SMT 3B battery charger1x operating instructions (German)

The Automatic-Charger Pb 1220 SMT 2B from Votronic (MPN 3101) is a modern battery charger for mobile use. It has charging programs for GEL, AGM, acid and modern lithium batteries and is designed for 12V battery voltage. The charging current at the main output is 20A. There is also a secondary charging output for the starter battery, which can supply an additional 2A charging current. The device is suitable for batteries with a capacity of 80 Ah - 145 Ah.Important features of the Pb 1220 SMT 2B battery charger reliably charges GEL, AGM, acid and LiFePO4 batteries 20A charging current, 2A charging current at the auxiliary charging output Official Votronic part number: 3101 Battery capacity (recommended): 80 Ah - 145 Ah Charging options: 1 supply battery and 1 starter battery The charging voltage is free of peaks and regulated in such a way that overcharging of the batteries is prevented. Fully automatic continuous operation: The charger can be permanently connected to the battery and keeps it fully charged. In the event of a power failure, the batteries are not discharged (disconnection by safety switch). Lithium LiFePO4 maintenance, auto wake-up, maintenance phase: Regular automatic activation of battery cell balancing every 10 days to ensure that the battery is always fully charged. Lead battery regeneration twice a week during long downtimes to prevent harmful acid stratification. Parallel and buffer operation: The battery continues to be charged or kept fully charged during simultaneous consumption. The charger automatically calculates and monitors the adjustment of the charging times. Monitoring-free charging: Multiple protection against overload, overheating, overvoltage, short circuit, polarity reversal, malfunction and battery back-discharge through electronic cut-off up to complete disconnection of charger and battery by built-in safety switches. Connection for battery temperature sensor (accessory temperature sensor 825, art. no. 2001): With lead batteries (acid, gel, AGM), the charging voltage is automatically adjusted to the battery temperature, resulting in a better full charge of the weaker battery in cold weather and avoiding unnecessary battery gassing and thus battery stress in summer temperatures. With LiFePO4 batteries, the battery temperature sensor is required for the function: It serves to protect the battery at high and especially at low temperatures below 0°C. Silent Run function: Noise-optimized operation at the touch of a button (night mode). Power supply unit function: Enables consumers to be supplied without a battery (e.g. battery replacement). Charging cable compensation: Voltage losses on the charging cables are automatically compensated for. Built-in on-board mains filter: Problem-free parallel operation with solar systems, wind and petrol generators, alternators etc. on one battery. Charging aid for deeply discharged lead batteries: Gentle pre-charging of the (lead-acid, -gel, -AGM) battery up to 8 V, then powerful support for the battery if consumers are still switched on. Disconnection of the batteries in the event of mains failure, overheating, malfunction (safety switch per charging output). Separate auxiliary charging output "S" for supporting and trickle charging the vehicle starter battery. Overview of the charging programs of the Pb 1220 SMT 2B"Gel": Charging program for gel batteries, characteristic curve IU1oU2oU3 Adapted to sealed, gas-tight gel/dryfit batteries with fixed electrolyte, which generally require a higher charging voltage level and longer U1 holding times in order to achieve short charging times with particularly high capacity storage and to avoid long-term battery "starvation"."AGM": Charging program for AGM/fleece batteries, characteristic curve IU1oU2oU3 Intended for charging sealed, gas-tight AGM (Absorbent Glass Mat) batteries in lead-fleece technology, which require a particularly high U1 level with coordinated holding times for full charging and then a moderate U2 level for charge retention (plate and round cell technology). ."UNIVERSAL": Charging program for lead-acid/wet/AGM batteries, characteristic curve IU1oU2oU3 Universal program for charging and charge retention of acid batteries in vehicles (mixed mobile/stationary). With a medium U1 level, still offers short charging times, a good charge factor and good acid mixing for open and closed, low-maintenance, maintenance-free standard, traction, lighting, solar and heavy-duty batteries, as well as AGM batteries with a normal U1 level."LiFePO4": Charging program for lithium batteries, characteristic curve IU1oU2oU3 Charging program tailored to lithium LiFePO4 batteries with their own BMS and prescribed or built-in protective circuitry. A special rest maintenance function automatically keeps the LiFePO4 battery at a charge level of 50-80% when the vehicle is parked (seasonal operation), which is beneficial for the service life, and also buffers 12 V consumers and the vehicle starter battery. In addition, a regular Auto Wake UP function activates the battery cell balancing.Scope of delivery:1X Votronic 3101 Pb 1220 SMT 2B battery charger1x operating instructions (German)