The Multiplus-II 48/5000/70-50 GX is a high-end device combination from Victron Energy (MPN PMP482506000) that combines classic Multiplus components with an external current sensor and integrated anti-islanding function. This extends the PowerControl and PowerAssist functions to 50 A and extends the potential range of use to ESS applications. The inverter module delivers a full 5000 W with a non-linear load and 4000 W with a linear continuous load. The 48 V battery charger is also very well proportioned with 70 A charging power and is supplemented by a 50 A transfer switch, which can be used to switch back and forth between the AC connections at lightning speed. Compared to the other devices in the series, the GX variants have an integrated GX display with numerous other connection options.Important features of the Multiplus-II 48/5000/70-50 GXIntegrated GX control unit with various communication connectionsPowerControl and PowerAssist to increase mains or generator outputbuilt-in anti-islanding function and connection option for external current sensor (optional)can be used as a backup device in grid-connected systems for power supply in the event of grid failurescan be used in various ESS (Energy Storage System) applicationsideally suited for professional seafaring, yachts, vehicles and land-based, off-grid applicationsVE.Bus interface for parallel and three-phase operation, remote monitoring and system integrationpractically unlimited power thanks to parallel and three-phase operationcan be configured on site or remotely using VEConfigure software* Technical features5000W power with non-linear load 4000 W continuous load and 9000 W peak powerfor 48 V battery voltage, 50 A transfer switch and 70 A battery chargerOutput voltage: 230 VAC, frequency: 50 Hzmax. efficiency is 95%, protection class IP22 Always enough power thanks to PowerControl and PowerAssistA maximum mains or generator current can be set on the MultiPlus-II 48/5000/70-50 GX. The MultiPlus-II then takes account of other connected AC consumers and only uses the power that is still "left over" to charge the battery. This prevents the generator or mains connection from being overloaded (PowerControl function). The PowerAssist function adds a new dimension to the PowerControl principle. Load peaks often only occur for a limited period of time. In such cases, the MultiPlus-II immediately compensates for insufficient generator, shore power or mains power with energy from the battery. If the load is reduced, i.e. consumers are switched off, the available energy can then be used to recharge the batteries.Solar power: alternating current even in the event of a mains failureThe device can be used with both off-grid and grid-connected PV systems as well as other alternative energy systems. It can be used with both solar charge controllers and grid-connected inverters.Maximum flexibility thanks to two AC outputsThe main output ensures uninterrupted operation. In the event of a mains failure or an interruption in the shore/generator current, the MultiPlus-II takes over the supply to the connected loads. The switchover takes place so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic devices is guaranteed. The second output only supplies power when alternating current is available at the input of the MultiPlus-II. Consumers that must not discharge the battery, such as a water heater, can be connected to this output.Scope of the integrated GX deviceA VE.Can interface This can be used to connect VE.Can devices from Victron (e.g. VE.Can MPPT). The connection can also be reconfigured via the remote console for use with a compatible CAN bus Li-ion battery.1xUSB connection1x Ethernet connection1x VE.Direct connectionMany options for system expansionThe settings can be changed within a few minutes using the VEConfigure software (a computer or laptop and an MK3 USB interface are required) and several monitoring and control options are available: Color Control GX, Venus GX, Octo GX, CANvu GX, laptop, computer, Bluetooth (with the optional VE.Bus Smart Dongle), battery monitor, Digital Multi control panel.Remote configuration and monitoringInstall a Color Control GX or other GX products to connect to the Internet. The operating data can be stored and viewed free of charge on our VRM (Victron Remote Management) website. If systems are connected to the Internet, they can be accessed remotely and settings can be changed.Scope of delivery:1x Victron PMP482506000 Multiplus-II 48/5000/70-50 GX 230V1x operating instructions

The Multiplus-II 48/5000/70-50 GX is a high-end device combination from Victron Energy (MPN PMP482506000) that combines classic Multiplus components with an external current sensor and integrated anti-islanding function. This extends the PowerControl and PowerAssist functions to 50 A and extends the potential range of use to ESS applications. The inverter module delivers a full 5000 W with a non-linear load and 4000 W with a linear continuous load. The 48 V battery charger is also very well proportioned with 70 A charging power and is supplemented by a 50 A transfer switch, which can be used to switch back and forth between the AC connections at lightning speed. Compared to the other devices in the series, the GX variants have an integrated GX display with numerous other connection options.Important features of the Multiplus-II 48/5000/70-50 GXIntegrated GX control unit with various communication connectionsPowerControl and PowerAssist to increase mains or generator outputbuilt-in anti-islanding function and connection option for external current sensor (optional)can be used as a backup device in grid-connected systems for power supply in the event of grid failurescan be used in various ESS (Energy Storage System) applicationsideally suited for professional seafaring, yachts, vehicles and land-based, off-grid applicationsVE.Bus interface for parallel and three-phase operation, remote monitoring and system integrationpractically unlimited power thanks to parallel and three-phase operationcan be configured on site or remotely using VEConfigure software* Technical features5000W power with non-linear load 4000 W continuous load and 9000 W peak powerfor 48 V battery voltage, 50 A transfer switch and 70 A battery chargerOutput voltage: 230 VAC, frequency: 50 Hzmax. efficiency is 95%, protection class IP22 Always enough power thanks to PowerControl and PowerAssistA maximum mains or generator current can be set on the MultiPlus-II 48/5000/70-50 GX. The MultiPlus-II then takes account of other connected AC consumers and only uses the power that is still "left over" to charge the battery. This prevents the generator or mains connection from being overloaded (PowerControl function). The PowerAssist function adds a new dimension to the PowerControl principle. Load peaks often only occur for a limited period of time. In such cases, the MultiPlus-II immediately compensates for insufficient generator, shore power or mains power with energy from the battery. If the load is reduced, i.e. consumers are switched off, the available energy can then be used to recharge the batteries.Solar power: alternating current even in the event of a mains failureThe device can be used with both off-grid and grid-connected PV systems as well as other alternative energy systems. It can be used with both solar charge controllers and grid-connected inverters.Maximum flexibility thanks to two AC outputsThe main output ensures uninterrupted operation. In the event of a mains failure or an interruption in the shore/generator current, the MultiPlus-II takes over the supply to the connected loads. The switchover takes place so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic devices is guaranteed. The second output only supplies power when alternating current is available at the input of the MultiPlus-II. Consumers that must not discharge the battery, such as a water heater, can be connected to this output.Scope of the integrated GX deviceA VE.Can interface This can be used to connect VE.Can devices from Victron (e.g. VE.Can MPPT). The connection can also be reconfigured via the remote console for use with a compatible CAN bus Li-ion battery.1xUSB connection1x Ethernet connection1x VE.Direct connectionMany options for system expansionThe settings can be changed within a few minutes using the VEConfigure software (a computer or laptop and an MK3 USB interface are required) and several monitoring and control options are available: Color Control GX, Venus GX, Octo GX, CANvu GX, laptop, computer, Bluetooth (with the optional VE.Bus Smart Dongle), battery monitor, Digital Multi control panel.Remote configuration and monitoringInstall a Color Control GX or other GX products to connect to the Internet. The operating data can be stored and viewed free of charge on our VRM (Victron Remote Management) website. If systems are connected to the Internet, they can be accessed remotely and settings can be changed.Scope of delivery:1x Victron PMP482506000 Multiplus-II 48/5000/70-50 GX 230V1x operating instructions

The new MultiPlus 12/1200/50-16 (Victron Energy, PMP122120000) is the successor to the Multiplus Compact 12/1200 and is a modern device combination consisting of a powerful inverter with pure sine wave, an advanced 50A battery charger that uses adaptive charging technology and a 16A high-speed AC voltage transfer switch.In the event of a mains fault or if the shore power or on-board generator is interrupted, the Multi's inverter is automatically switched on and takes over the supply to the connected loads. The switchover happens so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic devices is guaranteed.Key features of the MultiPlus 12/1200/50-16 Cont. Output power at 25°C: 1200WVictron Energy MPN: PMP122120000for 12V system voltageintegrated 50A mains charger for your batteriesintegrated 16A mains transfer switchUPS operation possibleExtensive range of accessories availableCan be used in numerous areas of application, whether on land or mobileProven reliability Complete bridging with an additional toroidal transformer topology has proven itself over many years. The inverter is short-circuit-proof and protected against overheating (whether caused by overload or ambient temperature).PowerControl - (Multiplus 800VA 1200VA only). The maximum mains or generator current to be drawn can be set using the Multi Control remote control panel. The MultiPlus then takes account of other connected AC consumers and only uses the current that is still “left over” for charging. This prevents the generator or shore power connection from being overloaded.PowerAssist - (Multiplus 800VA 1200VA only) Load peaks often only occur for a limited period of time. In such cases, the MultiPlus ensures that insufficient shore power or generator output is immediately compensated for by energy from the battery. If the load is reduced, i.e. consumers are switched off, the available energy can then be used to recharge the batteries.High switch-on power This is required to switch on loads with high inrush currents, such as voltage converters for LED lamps, halogen lamps or power tools.Search mode If the search mode is set to 'on', the power consumption of the inverter is reduced by approximately 70% in no-load operation. In this mode, when operated in inverter mode, the Multi switches off at zero load or at low load and switches on again every two seconds for a short period. If the output current exceeds a set limit value, the inverter resumes operation. If this is not the case, the inverter switches off again.Programmable relay In the default setting, the multifunction relay acts as an alarm relay, i.e. it switches the device off in the event of faults (device gets too hot, ripple voltage at the input too high, battery voltage too low).Scope of delivery:Victron Energy PMP122120000, MultiPlus 12/1200/50-16

The Quattro 12/3000/120-50/50 from Victron (MPN QUA123020010) is a device combination of a 12V 2400W sine wave inverter, a powerful battery charger and transfer switch. It has two switchable AC outputs and 2 AC inputs. The Quattro can be connected to two independent AC power sources: for example to the public power grid and a generator or to two generators. The Quattro automatically connects to the active source.The permanently integrated battery charger delivers an impressive 120A, which means that even large batteries can be fully charged quickly if shore/grid power is available. The 12V sine wave voltage converter built into the Quattro converts your battery current into 230V alternating current. Thanks to the true sine wave, the power quality is also perfect for sensitive electronic devices. In addition to the two integrated device types, 1 lightning-fast 50A transfer switch is installed for each AC input. Thanks to these switches, countless applications can also be implemented in the mains-coupled area. In addition to the VE.Bus port, 2 COM ports are also available for system integration, allowing virtually limitless networking of the Quattro.Extremely flexible thanks to 2 AC inputs and 2 AC outputsThe main output ensures uninterrupted operation. In the event of a mains failure or an interruption in the shore/generator power, the Quattro takes over the supply to the connected loads. The switchover happens so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic devices is guaranteed. The second output only supplies power if alternating current is available at one of the Quattro's inputs. Consumers that must not discharge the battery, such as a water heater, can be connected to this output.Key performance features of the Quattro 12/3000/120-50/502400W continuous power and 6000W peak power, for 12V battery voltageDevice combination of inverter with transfer switch and 120A battery chargersupplies the purest 230V sine wave voltage and a clean 50Hz frequency2 AC inputs with integrated transfer switch / 2 x 50 A maximum switchable current2 AC outputs + 1x additional output which only allows the current to pass to the consumer when the AC input is active.VE.Bus communication port provides extensive networking, system integration, configuration and control options for Victron Multiplus devices.supports three-phase operation (3 identical units of the same model required)Quattro devices can be connected in parallel, up to 6 devices can be connected in parallel, significantly increasing system performance if required2x COM ports are available in addition to the VE.Bus port, so there are virtually no limits to system integrationPowerControl function enables working with limited generator power as well as limited shore or mains powerPowerAssist function enables “power boosting” of generators and shore power support if requiredCan be used as a UPS solution for uninterruptible power supply, thanks to the integrated transfer switch with 16A or 50Acan be used for grid-connected self-consumption systems that only draw power from the grid operator when the battery capacity is no longer sufficient or other programmable events have occurred3 separately programmable relayscompatible with numerous Victron control and display panelsVery high efficiency and low self-consumptionMassive power expansion possibleUp to 6 Quattros can be connected in parallel. With six 48/10000/140 units, for example, this results in 54 kW/60 kVA power or 840 A charging current. Three units can be connected in a three-phase configuration. But that's not all: up to 6 sets of three units can be connected in parallel, resulting in 162 kW/180 kVA inverter power and over 2,500 A charging capacity.PowerControl - working with limited generator output, limited shore or mains powerThe MultiPlus is a very powerful battery charger. It therefore draws a lot of current from the generator or shore power supply (almost 10A per 5kVA Multi at 230 VAC). The maximum mains or generator current to be drawn can be set using the Multi Control remote control panel. The MultiPlus then takes other connected AC consumers into account and only uses the current that is still “left over” for charging. This prevents the generator or shore power connection from being overloaded.PowerAssist - “power boost” for generators and shore power supportThis function adds a new dimension to the PowerControl principle. It enables the Quattro to support alternative sources that are too weak. Load peaks often only occur for a limited period of time. In such cases, the MultiPlus ensures that insufficient shore power or generator output is immediately compensated for by energy from the battery.BackUp system: alternating current even in the event of a power failureThe Quattro can be used with non-grid-connected and grid-connected PV systems as well as other alternative energy systems. Software is available to detect a grid failure.Simple system configurationIf settings need to be changed on a single device, this can be done in a matter of minutes using a DIP switch setting procedure.Parallel-connected and three-phase systems can be configured using the VE.Bus Quick Configure and VE.Bus System Configurator software.Monitoring options and local controlSeveral options are available: Battery Monitor, Multi Control Panel, Ve.Net Blue Power Panel, Color Control Panel, Smartphone or Tablet (Bluetooth Smart), Laptop or Computer (USB or RS232).Monitoring and control from a distanceVictron Ethernet Remote, Victron Global Remote and the Color Control Panel enable remote maintenance and remote monitoring of the MultiPlus. System data can also be saved and viewed free of charge on the VRM (Victron Remote Management) website.Remote configurationIf systems with a Color Control Panel are connected to the Ethernet, they can be accessed and settings can be changed remotely.Scope of delivery:1x Victron QUA123020010 Quattro 12/3000/120-50/50 device combination consisting of 12V 2400W sine wave converter + 12V 120A battery charger + 2 AC inputs with integrated 50A transfer switches1x instruction manual

The Quattro 24/3000/70-50/50 from Victron (MPN QUA243020010) is a device combination of a 24V 2400W sine wave inverter, a powerful battery charger and transfer switch. It has two switchable AC outputs and 2 AC inputs, each equipped with a 50A transfer switch. The Quattro can be connected to two independent AC sources: for example, to the public power grid and a generator or to two generators. The Quattro automatically connects to the active source. The permanently integrated battery charger delivers an impressive 70A, which means that even large batteries can be fully charged quickly if shore/grid power is available. The 12V sine wave voltage converter built into the Quattro converts your battery current into 230V alternating current. Thanks to the true sine wave, the power quality is also perfect for sensitive electronic devices. In addition to the two integrated device types, 1 lightning-fast 50A transfer switch is installed for each AC input. Thanks to these switches, countless applications can also be implemented in the mains-coupled area. In addition to the VE.Bus port, 2 COM ports are also available for system integration, which enables virtually limitless networking of the Quattro. Extremely flexible thanks to 2 AC inputs and 2 AC outputsThe main output ensures uninterrupted operation. In the event of a mains failure or an interruption in the shore/generator power, the Quattro takes over the supply to the connected loads. The switchover happens so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic devices is guaranteed. The second output only supplies power if alternating current is available at one of the Quattro's inputs. Consumers that must not discharge the battery, such as a water heater, can be connected to this output. Key performance features of the Quattro 24/3000/70-50/502400W continuous power and 6000W peak power, for 24V battery voltageDevice combination of inverter with transfer switch and 70A battery chargersupplies the purest 230V sine wave voltage and a clean 50Hz frequency2 AC inputs with integrated transfer switch / 2 x 50 A maximum switchable current2 AC outputs + 1x additional output, which only allows the current to pass to the consumer when the AC input is active.VE.Bus communication port provides extensive networking, system integration, configuration and control options for Victron Multiplus devices.supports three-phase operation (3 identical units of the same model required)Multiplus devices can be connected in parallel, up to 6 devices can be connected in parallel, significantly increasing system performance if required2x COM ports are available in addition to the VE.Bus port, so there are virtually no limits to system integrationPowerControl function enables working with limited generator power as well as limited shore or mains powerPowerAssist function enables “power boosting” of generators and shore power support if requiredCan be used as a UPS solution for uninterruptible power supply, thanks to the integrated transfer switch with 16A or 50Acan be used for grid-connected self-consumption systems that only draw power from the grid operator when the battery capacity is no longer sufficient or other programmable events have occurred3 separately programmable relaysCompatible with numerous Victron control and display panelsVery high efficiency and low self-consumption Massive power expansion possibleUp to 6 Quattros can be connected in parallel. With six 48/10000/140 units, for example, this results in 54 kW/60 kVA power or 840 A charging current. Three units can be connected in a three-phase configuration. But that's not all: up to 6 sets of three units can be connected in parallel, resulting in 162 kW/180 kVA inverter power and over 2,500 A charging capacity.PowerControl - working with limited generator output, limited shore or mains powerThe MultiPlus is a very powerful battery charger. It therefore draws a lot of current from the generator or shore power supply (almost 10A per 5kVA Multi at 230 VAC). The maximum mains or generator current to be drawn can be set using the Multi Control remote control panel. The MultiPlus then takes other connected AC consumers into account and only uses the current that is still “left over” for charging. This prevents the generator or shore power connection from being overloaded. PowerAssist - “power boost” for generators and shore power supportThis function adds a new dimension to the PowerControl principle. It enables the Quattro to support alternative sources that are too weak. Load peaks often only occur for a limited period of time. In such cases, the Quattro ensures that insufficient shore power or generator output is immediately compensated for by energy from the battery. BackUp system: alternating current even in the event of a power failureThe Quattro can be used with non-grid-connected and grid-connected PV systems as well as other alternative energy systems. Software is available to detect a grid failure. Simple system configurationIf settings need to be changed on a single device, this can be done in a matter of minutes using a DIP switch setting procedure.Parallel and three-phase systems can be configured using the VE.Bus Quick Configure and VE.Bus System Configurator software.Monitoring options and local controlSeveral options are available: Battery Monitor, Multi Control Panel, Ve.Net Blue Power Panel, Color Control Panel, Smartphone or Tablet (Bluetooth Smart), Laptop or Computer (USB or RS232).Monitoring and control from a distanceVictron Ethernet Remote, Victron Global Remote and the Color Control Panel enable remote maintenance and remote monitoring of the MultiPlus. System data can also be saved and viewed free of charge on the VRM (Victron Remote Management) website.Remote configurationIf systems with a Color Control Panel are connected to the Ethernet, they can be accessed and settings can be changed remotely.Scope of delivery:1x Victron QUA243020010 Quattro 24/3000/70-50/50 device combination consisting of 24V 2400W sine wave converter + 24V 70A battery charger + 2 AC inputs with integrated 50A transfer switches1x instruction manual

The Quattro 48/5000/70-100/100 from Victron (MPN QUA485021010) is a device combination of a 48V 4000W sine wave inverter, a powerful battery charger and transfer switch. It has two switchable AC outputs and 2 AC inputs, each equipped with a 100A transfer switch. The Quattro can be connected to two independent AC power sources: for example, to the public power grid and a generator or to two generators. The Quattro automatically connects to the active source.The permanently integrated battery charger delivers an impressive 70A, which means that even large batteries can be fully charged quickly if shore/grid power is available. The 48V sine wave voltage converter built into the Quattro converts your battery current into 230V alternating current. Thanks to the true sine wave, the power quality is also perfect for sensitive electronic devices. In addition to the two integrated device types, 1 lightning-fast 100A transfer switch is installed for each AC input. Thanks to these switches, countless applications can also be implemented in the mains-coupled area. In addition to the VE.Bus port, 2 COM ports are also available for system integration, enabling virtually limitless networking of the Quattro.Extremely flexible thanks to 2 AC inputs and 2 AC outputsThe main output ensures uninterrupted operation. In the event of a mains failure or an interruption in the shore/generator power, the Quattro takes over the supply to the connected loads. The switchover happens so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic devices is guaranteed. The second output only supplies power if alternating current is available at one of the Quattro's inputs. Consumers that must not discharge the battery, such as a water heater, can be connected to this output.Key performance features of the Quattro 48/5000/70-100/1004000W continuous power and 10000W peak power, for 48V battery voltageDevice combination of inverter with transfer switch and 70A battery chargersupplies the purest 230V sine wave voltage and a clean 50Hz frequency2 AC inputs with integrated transfer switch / 2 x 100 A maximum switchable current2 AC outputs + 1x additional output which only allows the current to pass to the load when the AC input is active.VE.Bus communication port provides extensive networking, system integration, configuration and control options for Victron's Multiplus devices.supports three-phase operation (3 identical units of the same model required)Multiplus devices can be connected in parallel, up to 6 devices can be connected in parallel, significantly increasing system performance if required2x COM ports are available in addition to the VE. Bus port, so there are virtually no limits to system integrationPowerControl function enables working with limited generator power as well as limited shore or mains powerPowerAssist function enables "power boost" of generators and shore connection support if requiredcan be used as a UPS solution for uninterruptible power supply, thanks to the integrated transfer switch with 100A can be used for grid-connected self-consumption systems that only draw power from the grid operator when the battery capacity is no longer sufficient or other programmable events have occurred3 separately programmable relayscompatible with numerous Victron control and display panelsvery high efficiency and low self-consumptionmassive power expansion possibleUp to 6 Quattros can be connected in parallel. With six 48/10000/140 units, for example, this results in 54 kW/60 kVA power or 840 A charging current. Three units can be connected in a three-phase configuration. But that's not all: up to 6 sets of three units can be connected in parallel, resulting in 162 kW/180 kVA inverter power and over 2,500 A charging capacity.PowerControl - working with limited generator output, restricted shore or mains power The MultiPlus is a very powerful battery charger. It therefore draws a lot of current from the generator or shore power supply (almost 10A per 5kVA Multi at 230 VAC). The maximum mains or generator current to be drawn can be set using the Multi Control remote control panel. The MultiPlus then takes into account other connected AC consumers and only uses the current that is still "left over" for charging. This prevents the generator or shore power connection from being overloaded.PowerAssist - "power boost" for generators and shore power supportThis function adds a new dimension to the PowerControl principle. It enables the Quattro to support alternative sources that are too weak. Load peaks often only occur for a limited period of time. In such cases, the Quattro ensures that insufficient shore power or generator output is immediately compensated for by energy from the battery.BackUp system: Alternating current even in the event of a grid failureThe Quattro can be used with both non-grid-connected and grid-connected PV systems as well as other alternative energy systems. Software is available to detect a grid failure.Simple system configurationIf settings need to be changed on an individual device, this can be done within a few minutes using a DIP switch setting procedure.Parallel and three-phase systems can be configured using the VE.Bus Quick Configure and VE.Bus System Configurator software.Monitoring options and local controlSeveral options are available: Battery monitor, Multi Control Panel, Ve.Net Blue Power Panel, Color Control Panel, smartphone or tablet (Bluetooth Smart), laptop or computer (USB or RS232).Remote monitoring and controlVictron Ethernet Remote, Victron Global Remote and the Color Control Panel enable remote maintenance and remote monitoring of the MultiPlus. System data can also be saved and viewed free of charge on the VRM (Victron Remote Management) website.Remote configurationIf systems with a Color Control Panel are connected to the Ethernet, they can be accessed and settings can be changed remotely.Scope of delivery:1x Victron QUA485021010 Quattro 48/5000/70-100/100 device combination consisting of 48V 4000W sine wave converter + 48V 70A battery charger + 2 AC inputs with integrated 100A transfer switches1x operating manual

The Multiplus 12/2000/80-32 from Victron (MPN PMP122200000) is a device combination of 12V 2000W sine wave inverter and battery charger. The permanently integrated battery charger delivers an impressive 80A, which means that even large batteries can be fully charged quickly if shore/grid power is available. The 12V sine wave voltage converter built into the Multiplus converts your current from the battery into 230V alternating current. Thanks to the true sine wave, the power quality is also perfect for sensitive electronic devices. In addition to the two integrated device types, a lightning-fast 32A transfer switch is also installed, which can be used to implement numerous grid-connected solutions. The MultiPlus has a VE.Bus port for system integration, which enables virtually limitless networking.Comprehensive and flexible useAs it has a lightning-fast 32A transfer switch in addition to the inverter and charger, it is an ideal inverter for motorhomes, boats or yachts and for grid-connected uninterruptible power supplies in the event of grid fluctuations or power failures. Also for use in grid-connected self-consumption systems that only draw power from the supplier when the battery power is no longer sufficient or as a UPS solution in which the Multiplus steps in if the power from the grid operator suddenly fails and thus ensures an uninterruptible power supply.Key performance features of the Multiplus 12/2000/80-321600W continuous power and 3500W peak power, for 12V battery voltageDevice combination of inverter with transfer switch and 80A battery chargersupplies the purest 230V sine wave voltage and a clean 50Hz frequencyVE.Bus communication port provides extensive networking, system integration, configuration and control options for Victron Multiplus devicessupports three-phase operation (3 identical units of the same model required)Multiplus devices can be connected in parallel, up to 6 devices can be connected in parallel, significantly increasing system performance if requiredPowerControl function enables working with limited generator power as well as limited shore or mains powerPowerAssist function enables “power boost” of generators and shore connection support if requiredCan be used as a UPS solution for uninterruptible power supply thanks to the integrated transfer switchcan be used for grid-connected self-consumption systems that only draw power from the grid operator when the battery capacity is no longer sufficient or other programmable events have occurredCompatible with numerous Victron control and display panelsMassive power expansion possibleIn addition to the parallel connection, three units of the same model can be configured for a three-phase output. But that's not all: up to six sets of three units can be connected in parallel to achieve a huge charging capacityPowerControl - working with limited generator power, limited shore or mains powerThe MultiPlus is a very powerful battery charger. It therefore draws a lot of power from the generator or shore power supply. The maximum mains or generator current to be drawn can be set using the Multi Control remote control panel. The MultiPlus then takes other connected AC consumers into account and only uses the power that is still “left over” for charging. This prevents the generator or shore power connection from being overloaded.PowerAssist - “power boost” for generators and shore power supportThis function adds a new dimension to the PowerControl principle. It enables the MultiPlus to support alternative sources that are too weak. Load peaks often only occur for a limited period of time. In such cases, the MultiPlus ensures that insufficient shore power or generator output is immediately compensated for by energy from the battery.BackUp system: alternating current even in the event of a power failureThe MultiPlus can be used with both off-grid and grid-connected PV systems as well as other alternative energy systems. Software is available to detect a grid failure.Simple system configurationIf settings need to be changed on a single device, this can be done in a matter of minutes using a DIP switch setting procedure.Parallel and three-phase systems can be configured using the VE.Bus Quick Configure and VE.Bus System Configurator software.Monitoring options and on-site controlSeveral options are available: Battery monitor, Multi Control Panel, Ve.Net Blue Power Panel, Color Control Panel, smartphone or tablet (Bluetooth Smart), laptop or computer (USB or RS232).Remote monitoring and controlVictron Ethernet Remote, Victron Global Remote and the Color Control Panel enable remote maintenance and remote monitoring of the MultiPlus. System data can also be saved and viewed free of charge on the VRM (Victron Remote Management) website.Remote configurationIf systems with a Color Control Panel are connected to the Ethernet, they can be accessed and settings can be changed remotely.Scope of delivery:1x Victron PMP122200000 Multiplus 12/2000/80-32 device combination consisting of 12V 2000W sine wave converter + 12V 80A battery charger + 32A transfer switch1x operating instructions

Der Multiplus C 24/1200/25 von Victron (MPN CMP241220000) ist eine Gerätekombination aus 24V 1000W Sinus Wechselrichter und Batterie-Ladegerät.  Das fest integrierte Batterieladegerät leistet beachtliche 25A womit auch große Batterien schnell voll geladen werden können wenn Land-/Netzstrom zur Verfügung steht. Der im Multiplus verbaute 24V Sinus Spannungswandler wandelt Ihren Strom aus der Batterie in 230V Wechselstrom um. Dank der echten Sinuswelle ist die Stromqualität auch für empfindliche elektronische Geräte perfekt geeignet. Umfassend und flexibel einsetzbar Da er neben Wechselrichter und Ladegerät auch noch über einen blitzschnellen 16A Transferschalter verfügt, ist er ein idealer Wechselrichter für die Bereiche Wohnmobil, Boot oder Yacht und den netzgekoppelten Bereich der unterbrechungsfreien Stromversorgung im Falle von Netzschwankungen oder Stromausfällen. Auch für den Einsatz in netzgekoppelten Eigenverbrauchsanlagen, die nur Strom vom Versorger ziehen, wenn der Batteriestrom nicht mehr ausreicht oder als USV Lösung, in der die Multiplus einspringen, wenn der Strom vom Netzbetreiber plötzlich ausfällt und so für eine unterbrechungsfreie Stromversorgung sorgen. Wesentliche Leistungsmerkmale des Multiplus C 24/1200/25 1000W Dauerleistung und 2400W Spitzenleistung, für 24V BatteriespannungGerätekombination aus Wechselrichter mit Transfer-Switch und 25A Batterieladegerätliefert reinste 230V Sinusspannung und eine saubere 50Hz FrequenzVE.Bus Kommunikationsport sorgt für umfangreiche Möglichkeiten der Vernetzung, Systemintegration, Konfiguration und Kontrolle der Multiplus Geräte von Victron.unterstütz den Drei-Phasen-Betrieb (3 gleiche Einheiten desselben Models benötigt)Multiplus Geräte sind parallelschaltfähig, bis zu 6 Geräte lassen sich parallel verbinden und die Systemleistung dadurch im Bedarfsfall deutlich steigern2 Wechselstromausgänge ab Multiplus 3000 und größer. An dem zweiten Ausgang können dann zum Beispiel Geräte angeschlossen werden, die nur laufen sollen, wenn Netzstrom verfügbar istPowerControl Funktion ermöglicht das Arbeiten mit begrenzter Generatorleistung so wie eingeschränktem Land- oder NetzstromPowerAssist Funktion ermöglicht  „Leistungssteigerung“ von Generatoren und Landanschlussunterstützung im Bedarfsfallals USV Lösung zur unterbrechungsfreien Stromversorgung einsetzbarfür netzgekoppelte Eigenverbrauchsanlagen einsetzbar, die nur dann Strom vom Netzbetreiber ziehen, wenn die Batteriekapazität nicht mehr ausreicht oder andere programmierbare Ereignisse stattgefunden habenkompatibel mit zahlreichen Victron Steuer- und AnzeigepanelsDrei Phasenbetriebe mit baugleichen MultiPlus Wechselrichtern möglich massiver Leistungsausbau möglich Abgesehen von dem parallelen Anschluss, können auch drei Einheiten desselben Modells für einen Drei-Phasen-Ausgang konfiguriert werden. Damit jedoch nicht genug: Bis zu sechs Sets mit drei Einheiten können parallel geschaltet werden, um eine riesige 75 kW / 90 kVA Wechselrichter- und u¨ber 2.000 A Ladekapazita¨t zu erzielen (mit der 5000er-Version gerechnet) PowerControl – Arbeiten mit begrenzter Generatorleistung, eingeschränktem Land- oder Netzstrom Der MultiPlus ist ein sehr leistungsstarkes Batterieladegerät. Daher nimmt er vom Generator bzw. der Landstromversorgung viel Strom auf (fast 10A pro 5kVA Multi bei 230 VAC). Mit dem Fernbedienungspaneel Multi Control kann der maximal zu entnehmende Netz- bzw. Generatorstrom eingestellt werden. Der MultiPlus nimmt dann Rücksicht auf weitere angeschlossene Wechselstromverbraucher und nutzt zum Laden nur den Strom, der noch „übrig“ ist. So wird verhindert, dass der Generator- oder der Landstromanschluss überlastet wird. PowerAssist – „Leistungssteigerung“ von Generatoren und Landanschlussunterstu¨tzung Mit dieser Funktion erhält das PowerControl-Prinzip eine neue Dimension. Sie ermöglicht, dass der MultiPlus zu schwach ausgelegte alternative Quellen stützt. Lastspitzen treten häufig nur für einen begrenzten Zeitraum auf. In einem solchen Fall stellt der MultiPlus sicher, dass eine zu schwache Landstrom- bzw. Generatorleistung sofort durch Energie aus der Batterie kompensiert wird. BackUp-System: Wechselstrom auch bei Netzausfall Der Multiplus kann sowohl bei nicht netzgekoppelten sowie bei netzgekoppelten PV-Anlagen als auch bei anderen alternativen Energiesystemen eingesetzt werden. Es ist eine Software zur Erkennung eines Netzausfalls verfügbar. Einfache Systemkonfiguration Wenn Einstellungen an einem Einzelgerät verändert werden müssen, kann dies innerhalb von wenigen Minuten mithilfe eines DIP-Schalter-Einstellungsverfahrens erfolgen. Parallel geschaltete und Drei-Phasen-Systeme können mit der VE.Bus Quick Configure- und VE.Bus System Configurator Software konfiguriert werden. Überwachungsoptionen und Steuerung vor Ort Es stehen mehrere Optionen zur Verfügung: Batteriewächter, Multi Control Paneel, Ve.Net Blue Power Paneel, Color Control Paneel, Smartphone oder Tablet (Bluetooth Smart), Laptop oder Computer (USB oder RS232). Überwachung und Steuerung aus der Ferne Victron Ethernet Remote, Victron Global Remote und das Color Control Panel ermöglichen Fernwartung und Fernüberwachung des MultiPlus.  Zudem lassen sich die Systemdaten auf der VRM (Victron Remote Management) Website kostenlos speichern und einsehen. Konfigurierung aus der Ferne Sind Systeme mit einem Color Control Paneel an das Ethernet angeschlossen, kann auf sie zugegriffen werden und Einstellungen können aus der Ferne geändert werden. Lieferumfang: 1x Victron CMP241220000 Multiplus C 24/1200/25 Gerätekombination bestehend aus 24V 1000W Sinus Wandler + 24V 25A Batterieladegerät 1x Bedienungsanleitung

Der Multiplus C 12/1200/50 von Victron (MPN CMP121220000) ist eine Gerätekombination aus 12V 1000W Sinus Wechselrichter und Batterie-Ladegerät.  Das fest integrierte Batterieladegerät leistet beachtliche 35A, womit auch große Batterien schnell voll geladen werden können, wenn Land-/Netzstrom zur Verfügung steht. Der im Multiplus verbaute 12V Sinus Spannungswandler wandelt Ihren Strom aus der Batterie in 230V Wechselstrom um. Dank der echten Sinuswelle ist die Stromqualität auch für empfindliche elektronische Geräte perfekt geeignet. Umfassend und flexibel einsetzbar Da er neben Wechselrichter und Ladegerät auch noch über einen blitzschnellen 16A Transferschalter verfügt, ist er ein idealer Wechselrichter für die Bereiche Wohnmobil, Boot oder Yacht und den netzgekoppelten Bereich der unterbrechungsfreien Stromversorgung im Falle von Netzschwankungen oder Stromausfällen. Auch für den Einsatz in netzgekoppelten Eigenverbrauchsanlagen, die nur Strom vom Versorger ziehen, wenn der Batteriestrom nicht mehr ausreicht oder als USV Lösung, in der die Multiplus einspringen, wenn der Strom vom Netzbetreiber plötzlich ausfällt und so für eine unterbrechungsfreie Stromversorgung sorgen. Wesentliche Leistungsmerkmale des Multiplus C 12/1200/50 1000W Dauerleistung und 2400W Spitzenleistung, für 12V BatteriespannungGerätekombination aus Wechselrichter mit Transfer-Switch und 50A Batterieladegerätliefert reinste 230V Sinusspannung und eine saubere 50Hz FrequenzVE.Bus Kommunikationsport sorgt für umfangreiche Möglichkeiten der Vernetzung, Systemintegration, Konfiguration und Kontrolle der Multiplus Geräte von Victron.unterstütz den Drei-Phasen-Betrieb (3 gleiche Einheiten desselben Models benötigt)Multiplus Geräte sind parallelschaltfähig, bis zu 6 Geräte lassen sich parallel verbinden und die Systemleistung dadurch im Bedarfsfall deutlich steigern2 Wechselstromausgänge ab Multiplus 3000 und größer. An dem zweiten Ausgang können dann zum Beispiel Geräte angeschlossen werden, die nur laufen sollen, wenn Netzstrom verfügbar istPowerControl Funktion ermöglicht das Arbeiten mit begrenzter Generatorleistung so wie eingeschränktem Land- oder NetzstromPowerAssist Funktion ermöglicht  „Leistungssteigerung“ von Generatoren und Landanschlussunterstützung im Bedarfsfallals USV Lösung zur unterbrechungsfreien Stromversorgung einsetzbarfür netzgekoppelte Eigenverbrauchsanlagen einsetzbar, die nur dann Strom vom Netzbetreiber ziehen, wenn die Batteriekapazität nicht mehr ausreicht oder andere programmierbare Ereignisse stattgefunden habenkompatibel mit zahlreichen Victron Steuer- und AnzeigepanelsDrei Phasen-Betrieb mit baugleichen MultiPlus Wechselrichtern möglich massiver Leistungsausbau möglich Abgesehen von dem parallelen Anschluss, können auch drei Einheiten desselben Modells für einen Drei-Phasen-Ausgang konfiguriert werden. Damit jedoch nicht genug: Bis zu sechs Sets mit drei Einheiten können parallel geschaltet werden, um eine riesige 75 kW / 90 kVA Wechselrichter- und u¨ber 2.000 A Ladekapazita¨t zu erzielen (mit der 5000er Version gerechnet) PowerControl – Arbeiten mit begrenzter Generatorleistung, eingeschränktem Land- oder Netzstrom Der MultiPlus ist ein sehr leistungsstarkes Batterieladegerät. Daher nimmt er vom Generator bzw. der Landstromversorgung viel Strom auf (fast 10A pro 5kVA Multi bei 230 VAC). Mit dem Fernbedienungspaneel Multi Control kann der maximal zu entnehmende Netz- bzw. Generatorstrom eingestellt werden. Der MultiPlus nimmt dann Rücksicht auf weitere angeschlossene Wechselstromverbraucher und nutzt zum Laden nur den Strom, der noch „übrig“ ist. So wird verhindert, dass der Generator- oder der Landstromanschluss überlastet wird. PowerAssist – „Leistungssteigerung“ von Generatoren und Landanschlussunterstu¨tzung Mit dieser Funktion erhält das PowerControl-Prinzip eine neue Dimension. Sie ermöglicht, dass der MultiPlus zu schwach ausgelegte alternative Quellen stützt. Lastspitzen treten häufig nur für einen begrenzten Zeitraum auf. In einem solchen Fall stellt der MultiPlus sicher, dass eine zu schwache Landstrom- bzw. Generatorleistung sofort durch Energie aus der Batterie kompensiert wird. BackUp-System: Wechselstrom auch bei Netzausfall Der Multiplus kann sowohl bei nicht netzgekoppelten sowie bei netzgekoppelten PV-Anlagen als auch bei anderen alternativen Energiesystemen eingesetzt werden. Es ist eine Software zur Erkennung eines Netzausfalls verfügbar. Einfache Systemkonfiguration Wenn Einstellungen an einem Einzelgerät verändert werden müssen, kann dies innerhalb von wenigen Minuten mithilfe eines DIP-Schalter-Einstellungsverfahrens erfolgen. Parallel geschaltete und Drei-Phasen-Systeme können mit der VE.Bus Quick Configure- und VE.Bus System Configurator Software konfiguriert werden. Überwachungsoptionen und Steuerung vor Ort Es stehen mehrere Optionen zur Verfügung: Batteriewächter, Multi Control Paneel, Ve.Net Blue Power Paneel, Color Control Paneel, Smartphone oder Tablet (Bluetooth Smart), Laptop oder Computer (USB oder RS232). Überwachung und Steuerung aus der Ferne Victron Ethernet Remote, Victron Global Remote und das Color Control Panel ermöglichen Fernwartung und Fernüberwachung des MultiPlus.  Zudem lassen sich die Systemdaten auf der VRM (Victron Remote Management) Website kostenlos speichern und einsehen. Konfigurierung aus der Ferne Sind Systeme mit einem Color Control Paneel an das Ethernet angeschlossen, kann auf sie zugegriffen werden und Einstellungen können aus der Ferne geändert werden. Lieferumfang: 1x Victron CMP121220000 Multiplus C 12/1200/50 Gerätekombination bestehend aus 12V 1000W Sinus Wandler + 12V 50A Batterieladegerät 1x Bedienungsanleitung

Der Multiplus C 12/2000/80 von Victron (MPN CMP122020000) ist eine Gerätekombination aus 12V 1600W Sinus Wechselrichter und Batterie-Ladegerät.  Das fest integrierte Batterieladegerät leistet beachtliche 80A womit auch große Batterien schnell voll geladen werden können, wenn Land-/Netzstrom zur Verfügung steht. Der im Multiplus verbaute 12V Sinus Spannungswandler wandelt Ihren Strom aus der Batterie in 230V Wechselstrom um. Dank der echten Sinuswelle ist die Stromqualität auch für empfindliche elektronische Geräte perfekt geeignet. Umfassend und flexibel einsetzbar Da er neben Wechselrichter und Ladegerät auch noch über einen blitzschnellen 30A Transferschalter verfügt, ist er ein idealer Wechselrichter für die Bereiche Wohnmobil, Boot oder Yacht und den netzgekoppelten Bereich der unterbrechungsfreien Stromversorgung im Falle von Netzschwankungen oder Stromausfällen. Auch für den Einsatz in netzgekoppelten Eigenverbrauchsanlagen, die nur Strom vom Versorger ziehen, wenn der Batteriestrom nicht mehr ausreicht oder als USV Lösung, in der die Multiplus einspringen, wenn der Strom vom Netzbetreiber plötzlich ausfällt und so für eine unterbrechungsfreie Stromversorgung sorgen. Wesentliche Leistungsmerkmale des Multiplus C 12/2000/80 1600W Dauerleistung und 4000W Spitzenleistung, für 12V BatteriespannungGerätekombination aus Wechselrichter mit Transfer-Switch und 80A Batterieladegerätliefert reinste 230V Sinusspannung und eine saubere 50Hz FrequenzVE.Bus Kommunikationsport sorgt für umfangreiche Möglichkeiten der Vernetzung, Systemintegration, Konfiguration und Kontrolle der Multiplus Geräte von Victronunterstütz den Drei-Phasen-Betrieb (3 gleiche Einheiten desselben Models benötigt)Multiplus Geräte sind parallelschaltfähig, bis zu 6 Geräte lassen sich parallel verbinden und die Systemleistung dadurch im Bedarfsfall deutlich steigern2 Wechselstromausgänge ab Multiplus 3000 und größer. An dem zweiten Ausgang können dann zum Beispiel Geräte angeschlossen werden, die nur laufen sollen, wenn Netzstrom verfügbar istPowerControl Funktion ermöglicht das Arbeiten mit begrenzter Generatorleistung so wie eingeschränktem Land- oder NetzstromPowerAssist Funktion ermöglicht  „Leistungssteigerung“ von Generatoren und Landanschlussunterstützung im Bedarfsfallals USV Lösung zur unterbrechungsfreien Stromversorgung einsetzbarfür netzgekoppelte Eigenverbrauchsanlagen einsetzbar, die nur dann Strom vom Netzbetreiber ziehen, wenn die Batteriekapazität nicht mehr ausreicht oder andere programmierbare Ereignisse stattgefunden habenkompatibel mit zahlreichen Victron Steuer- und AnzeigepanelsDrei Phasen-Betrieb mit baugleichen MultiPlus Wechselrichtern möglich massiver Leistungsausbau möglich Abgesehen von dem parallelen Anschluss, können auch drei Einheiten desselben Modells für einen Drei-Phasen-Ausgang konfiguriert werden. Damit jedoch nicht genug: Bis zu sechs Sets mit drei Einheiten können parallel geschaltet werden, um eine riesige 75 kW / 90 kVA Wechselrichter- und über 2.000 A Ladekapazität zu erzielen (mit der 5000er-Version gerechnet) PowerControl – Arbeiten mit begrenzter Generatorleistung, eingeschränktem Land- oder Netzstrom Der MultiPlus ist ein sehr leistungsstarkes Batterieladegerät. Daher nimmt er vom Generator bzw. der Landstromversorgung viel Strom auf (fast 10A pro 5kVA Multi bei 230 VAC). Mit dem Fernbedienungspaneel Multi Control kann der maximal zu entnehmende Netz- bzw. Generatorstrom eingestellt werden. Der MultiPlus nimmt dann Rücksicht auf weitere angeschlossene Wechselstromverbraucher und nutzt zum Laden nur den Strom, der noch „übrig“ ist. So wird verhindert, dass der Generator- oder der Landstromanschluss überlastet wird. PowerAssist – „Leistungssteigerung“ von Generatoren und Landanschlussunterstützung Mit dieser Funktion erhält das PowerControl-Prinzip eine neue Dimension. Sie ermöglicht, dass der MultiPlus zu schwach ausgelegte alternative Quellen stützt. Lastspitzen treten häufig nur für einen begrenzten Zeitraum auf. In einem solchen Fall stellt der MultiPlus sicher, dass eine zu schwache Landstrom- bzw. Generatorleistung sofort durch Energie aus der Batterie kompensiert wird. BackUp-System: Wechselstrom auch bei Netzausfall Der Multiplus kann sowohl bei nicht netzgekoppelten sowie bei netzgekoppelten PV-Anlagen als auch bei anderen alternativen Energiesystemen eingesetzt werden. Es ist eine Software zur Erkennung eines Netzausfalls verfügbar. Einfache Systemkonfiguration Wenn Einstellungen an einem Einzelgerät verändert werden müssen, kann dies innerhalb von wenigen Minuten mithilfe eines DIP-Schalter-Einstellungsverfahrens erfolgen. Parallel geschaltete und Drei-Phasen-Systeme können mit der VE.Bus Quick Configure- und VE.Bus System Configurator Software konfiguriert werden. Überwachungoptionen und Steuerung vor Ort Es stehen mehrere Optionen zur Verfügung: Batteriewächter, Multi Control Paneel, Ve.Net Blue Power Paneel, Color Control Paneel, Smartphone oder Tablet (Bluetooth Smart), Laptop oder Computer (USB oder RS232). Überwachung und Steuerung aus der Ferne Victron Ethernet Remote, Victron Global Remote und das Color Control Panel ermöglichen Fernwartung und Fernüberwachung des MultiPlus.  Zudem lassen sich die Systemdaten auf der VRM (Victron Remote Management) Website kostenlos speichern und einsehen. Konfigurierung aus der Ferne Sind Systeme mit einem Color Control Paneel an das Ethernet angeschlossen, kann auf sie zugegriffen werden und Einstellungen können aus der Ferne geändert werden. Lieferumfang: 1x Victron CMP122020000 Multiplus C 12/2000/80 Gerätekombination bestehend aus 12V 1600W Sinus Wandler + 12V 80A Batterieladegerät 1x Bedienungsanleitung

The Multiplus C 24/2000/50 from Victron (MPN CMP242200000) is a device combination of 24V 1600W sine wave inverter and battery charger. The permanently integrated battery charger delivers a remarkable 50A, which means that even large batteries can be fully charged quickly if shore/grid power is available. The 24V sine wave voltage converter built into the Multiplus converts your current from the battery into 230V alternating current. Thanks to the genuine sine wave, the power quality is also perfect for sensitive electronic devices.Comprehensive and flexible in useAs it also has a lightning-fast 30A transfer switch in addition to the inverter and charger, it is an ideal inverter for motorhomes, boats or yachts and the grid-connected area of the uninterruptible power supply in the event of grid fluctuations or power failures. Also for use in grid-connected self-consumption systems that only draw power from the supplier when the battery power is no longer sufficient or as a UPS solution in which the Multiplus steps in if the power from the grid operator suddenly fails and thus ensures an uninterruptible power supply.Key performance features of the Multiplus C 24/2000/501600W continuous power and 4000W peak power, for 24V battery voltageDevice combination of inverter with transfer switch and 50A battery chargersupplies the purest 230V sine wave voltage and a clean 50Hz frequencyVE.Bus communication port provides extensive networking, system integration, configuration and control options for Victron Multiplus devices.supports three-phase operation (3 identical units of the same model required)Multiplus devices can be connected in parallel, up to 6 devices can be connected in parallel, significantly increasing system performance if required2 AC outputs from Multiplus 3000 and larger. The second output can then be used, for example, to connect devices that should only run when mains power is availablePowerControl function enables working with limited generator output as well as limited shore or mains powerPowerAssist function enables “power boosting” of generators and shore power support if requiredCan be used as a UPS solution for uninterruptible power supplycan be used for grid-connected self-consumption systems that only draw power from the grid operator when the battery capacity is no longer sufficient or other programmable events have occurredcompatible with numerous Victron control and display panelsThree-phase operation possible with identical MultiPlus invertersMassive power expansion possibleIn addition to the parallel connection, three units of the same model can also be configured for a three-phase output. But that's not all: up to six sets of three units can be connected in parallel to achieve a huge 75 kW / 90 kVA inverter and over 2,000 A charging capacity (calculated with the 5000 version)PowerControl - working with limited generator output, limited shore or mains powerThe MultiPlus is a very powerful battery charger. It therefore draws a lot of current from the generator or shore power supply (almost 10A per 5kVA Multi at 230 VAC). The maximum mains or generator current to be drawn can be set using the Multi Control remote control panel. The MultiPlus then takes into account other connected AC consumers and only uses the current that is still “left over” for charging. This prevents the generator or shore power connection from being overloaded.PowerAssist - “power boost” for generators and shore power supportThis function adds a new dimension to the PowerControl principle. It enables the MultiPlus to support alternative sources that are too weak. Load peaks often only occur for a limited period of time. In such cases, the MultiPlus ensures that insufficient shore power or generator output is immediately compensated for by energy from the battery.BackUp system: alternating current even in the event of a power failureThe MultiPlus can be used with both off-grid and grid-connected PV systems as well as other alternative energy systems. Software is available to detect a grid failure.Simple system configurationIf settings need to be changed on a single device, this can be done in a matter of minutes using a DIP switch setting procedure.Parallel-connected and three-phase systems can be configured using the VE.Bus Quick Configure and VE.Bus System Configurator software.Monitoring options and local controlSeveral options are available: Battery Monitor, Multi Control Panel, Ve.Net Blue Power Panel, Color Control Panel, Smartphone or Tablet (Bluetooth Smart), Laptop or Computer (USB or RS232).Monitoring and control from a distanceVictron Ethernet Remote, Victron Global Remote and the Color Control Panel enable remote maintenance and remote monitoring of the MultiPlus. System data can also be stored and viewed free of charge on the VRM (Victron Remote Management) website.Remote configurationIf systems with a Color Control Panel are connected to the Ethernet, they can be accessed and settings can be changed remotely.Scope of delivery:1x Victron CMP242200000 Multiplus C 24/2000/50 device combination consisting of 24V 1600W sine wave converter + 24V 50A battery charger1x operating instructions

The MultiPlus C 12/1600/70-16 from Victron (MPN: CMP122160000) is a powerful combination of devices for your energy supply system. It combines a 12V 1300W sine wave inverter and an efficient battery charger. This provides you with an impressive 70A, so that even large batteries can be charged quickly when shore or mains power is available. The inverter converts the battery current into 230V alternating current and thus offers optimum power quality for sensitive electronic devices. In addition, the MultiPlus has a lightning-fast 16A transfer switch, making it ideal for motorhomes, boats, yachts and grid-connected UPS systems. In self-consumption systems, it ensures that power is only drawn from the mains when the battery power is insufficient. In the event of a mains failure, it guarantees an uninterrupted power supply. Highlights of the MultiPlus C 12/1600/70 Device combination of inverter with transfer switch and 70A battery chargerVE.Bus communication port for networking, system integration and configurationsSupports three-phase operation in parallel connectionmonitoring on site or via remote monitoring with the appTwo alternating current outputsPowerControl mechanismPowerAssistProgrammable relayVersatile in useFor off-grid and grid-connected PV systems Massive power expansion possible In addition to parallel connection, three units of the same model can also be combined to create a powerful three-phase output configuration. But that's not all - up to six sets of three units can be connected in parallel to achieve an impressive 75kW / 90kVA inverter power and over 2,000A charging capacity. PowerControl The MultiPlus is an extremely powerful battery charger that requires a relatively large amount of power from the generator or shore power connection (almost 10A per 5kVA Multi at 230V AC). However, with the Multi Control remote control panel you can easily set the maximum power consumption, automatically taking into account the other connected devices and only using the excess power for charging. This ensures that the generator or shore power connection is never overloaded. PowerAssist This function takes the PowerControl principle to a new level. The MultiPlus can now effectively support weak alternative energy sources. As load peaks often only occur for a short time, the device combination ensures that insufficient shore power or generator output is immediately compensated for by energy from the battery. As soon as the loads decrease, i.e. when consumers are switched off, the surplus energy can be used efficiently to charge the batteries again. System configuration You can make settings on a single device in just a few minutes using a DIP switch procedure. Parallel and three-phase systems can be easily configured using the VE.Bus Quick Configure and VE.Bus System Configurator software. Off-grid, grid-connected and self-consumption systems in which grid-tie inverters and/or MPPT solar chargers are used can be easily configured using the corresponding wizard software. surveillance - wherever and whenever you want You have several options for keeping an eye on your data either on site or via remote monitoring and being able to react immediately. Here are a few examples for you: Ekrano GX and Cerbo GX - Provides user-friendly system control and monitoring and allows access to the free VRM Online Portal for remote viewing.VRM Portal - This free tool displays all your system data in a clear graphical format. you can use this application to make system changes conveniently from anywhere. You also receive alerts directly by email or push notification.VRM app - You can conveniently monitor and manage your Victron Energy system via your smartphone or tablet. The app is available for both iOS and Android. Technical data Inverter Input voltage range: 9-17V DC / 19-33V DC / 38-66V DCOutput voltage: 230V AC ± 2%Frequency: 50Hz ± 1%Cont. Output power at 25°C: 1600VA (non-linear load)Cont. Output power at 25°C: 1300WCont. Output power at 40°C: 1200WCont. Output power at 65°C: 800WPeak power: 3000WMax. Efficiency: 93% Charger Input voltage range: 187-265V ACInput frequency: 45-65Hz / power factor: 1Charging voltage constant voltage: 14.4/28.8/57.6V DCCharging voltage - charge retention: 13.8/27.6/55.2V DCStorage mode: 13.2/26.4/52.8V DCCharging current house battery: 70ACharging current starter battery: 4A (12V and 24V models only) General information AC input - input voltage range: 187-250VAC input - input frequency: 50/60HzTransfer switch: 16AOperating temperature range: -40°C - +65°CHumidity: max. 95% (non-condensing)Battery connection: 1.5m battery cable230V AC connection: G-St18i connectionProtection class: IP20Weight: 10kgDimensions: 375 x 214 x 110mm Scope of delivery 1x Victron MultiPlus C 12/1600/70-16 230V VE.Bus device combination 3000W inverter 70A charger

The new MultiPlus 12/800/35-16 (Victron Energy, PMP121800000) is the successor to the Multiplus Compact 12/800 and is a modern device combination consisting of a powerful inverter with pure sine wave, an advanced 50A battery charger that uses adaptive charging technology and a 16A high-speed AC voltage transfer switch.In the event of a mains fault or if the shore power or on-board generator is interrupted, the Multi's inverter is automatically switched on and takes over the supply to the connected loads. The switchover happens so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic devices is guaranteed.Key features of the MultiPlus 12/800/35-16Cont. Output power at 25°C: 700W / 800W with non-linear loadVictron Energy MPN: PMP121800000for 12V system voltageintegrated 35A mains charger for your batteriesintegrated 16A mains transfer switchUPS operation possibleExtensive range of accessories availableCan be used in numerous areas of application, whether on land or mobileProven reliabilityComplete bridging with an additional toroidal transformer topology has proven itself over many years. The inverter is short-circuit-proof and protected against overheating (whether caused by overload or ambient temperature).PowerControl - (Multiplus 800VA 1200VA only)The maximum mains or generator current to be drawn can be set using the Multi Control remote control panel. The MultiPlus then takes account of other connected AC consumers and only uses the current that is still “left over” for charging. This prevents the generator or shore power connection from being overloaded.PowerAssist - (Multiplus 800VA 1200VA only)Load peaks often only occur for a limited period of time. In such cases, the MultiPlus ensures that insufficient shore power or generator output is immediately compensated for by energy from the battery. If the load is reduced, i.e. consumers are switched off, the available energy can then be used to recharge the batteries.High switch-on powerThis is required to switch on loads with high inrush currents, such as voltage converters for LED lamps, halogen lamps or power tools.Search modeIf the search mode is set to 'on', the power consumption of the inverter is reduced by around 70% in no-load operation. In this mode, when operated in inverter mode, the Multi switches off at zero load or at low load and switches on again every two seconds for a short period. If the output current exceeds a set limit value, the inverter resumes operation. If this is not the case, the inverter switches off again.Programmable relayIn the default setting, the multifunction relay acts as an alarm relay, i.e. it switches the device off in the event of faults (device gets too hot, ripple voltage at the input too high, battery voltage too low).Scope of delivery:Victron Energy PMP121800000, MultiPlus 12/800/35-16

The Multiplus-II 12/3000/120-32 is a high-end device combination from Victron Energy (MPN PMP122305010) that combines classic Multiplus components with an external current sensor and integrated anti-islanding function. This extends the PowerControl and PowerAssist functions to 50 A. The inverter module delivers a full 3000 W with a non-linear load or 2400 W with a linear continuous load. The 12 V battery charger is also very well proportioned with 120 A charging power and is supplemented by a 32 A transfer switch, which can be used to switch back and forth between the AC connections at lightning speed. Important features of the Multiplus-II 12/3000/120-32 PowerControl and PowerAssist increase of mains or generator power Built-in anti-islanding function and connection option for external current sensor (optional) can be used as a backup device in grid-connected systems for power supply in the event of grid failures Can be used in various applications ideally suited for professional seafaring, yachts, vehicles and land-based, off-grid applications VE.Bus interface for parallel and three-phase operation, remote monitoring and system integration practically unlimited power thanks to parallel and three-phase operation can be configured on site or remotely using VEConfigure software* Technical features 3000 W power with non-linear load 2400 W continuous load and 5500 W peak power for 12 V battery voltage, 32 A transfer switch and 120 A battery charger Output voltage: 230 VAC, frequency: 50 Hz Max. efficiency is 95%, protection class IP22 Always enough power thanks to PowerControl and PowerAssist A maximum mains or generator current can be set on the MultiPlus-II 12/3000/120-32. The MultiPlus-II then takes account of other connected AC consumers and only uses the current that is still "left over" to charge the battery. This prevents the generator or mains connection from being overloaded (PowerControl function). The PowerAssist function adds a new dimension to the PowerControl principle. Load peaks often only occur for a limited period of time. In such cases, the MultiPlus-II immediately compensates for insufficient generator, shore power or mains power with energy from the battery. If the load is reduced, i.e. consumers are switched off, the available energy can then be used to recharge the batteries. Solar power: alternating current even in the event of a mains failure The device can be used with both off-grid and grid-connected PV systems as well as other alternative energy systems. It can be used with both solar charge controllers and grid-connected inverters. Maximum flexibility thanks to two AC outputs The main output ensures uninterrupted operation. In the event of a mains failure or an interruption in the shore/generator current, the MultiPlus-II takes over the supply to the connected loads. The switchover takes place so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic devices is guaranteed. The second output only supplies power when alternating current is available at the input of the MultiPlus-II. Consumers that must not discharge the battery, such as a water heater, can be connected to this output. Many options for system expansion The settings can be changed in a matter of minutes using the VEConfigure software (a computer or laptop and an MK3 USB interface are required) and several monitoring and control options are available: Color Control GX, Venus GX, Octo GX, CANvu GX, laptop, computer, Bluetooth (with the optional VE.Bus Smart Dongle), battery monitor, Digital Multi control panel. Remote configuration and monitoring Install a Color Control GX or other GX products to connect to the Internet. The operating data can be stored and viewed free of charge on our VRM (Victron Remote Management) website. If systems are connected to the Internet, they can be accessed remotely and settings can be changed. Scope of delivery: 1x Victron PMP122305010 Multiplus-II 12/3000/120-32A1x operating instructions

The Multiplus-II 24/3000/70-32 is a high-end device combination from Victron Energy (MPN PMP242305010) that combines classic Multiplus components with an external current sensor and integrated anti-islanding function. This extends the PowerControl and PowerAssist functions to 50 A and extends the potential range of use to ESS applications. The inverter module delivers a full 3000 W with a non-linear load or 2400 W with a linear continuous load. The 24 V battery charger is also very well proportioned with 70 A charging power and is supplemented by a 32 A transfer switch, which can be used to switch back and forth between the AC connections at lightning speed. Important features of the Multiplus-II 24/3000/70-32 PowerControl and PowerAssist increase mains or generator output built-in anti-islanding function and connection option for external current sensor (optional) can be used as a backup device in grid-connected systems for power supply in the event of grid failures can be used in various ESS (Energy Storage System) applications ideally suited for professional seafaring, yachts, vehicles and land-based, off-grid applications VE.Bus interface for parallel and three-phase operation, remote monitoring and system integration practically unlimited power thanks to parallel and three-phase operation can be configured on site or remotely using VEConfigure software* Technical features 3000 W power with non-linear load 2400 W continuous load and 6000 W peak power for 24 V battery voltage, 32 A transfer switch and 70 A battery charger Output voltage: 230 VAC, frequency: 50 Hz Max. efficiency is 95%, protection class IP22 Always enough power thanks to PowerControl and PowerAssist A maximum mains or generator current can be set on the MultiPlus-II 24/3000/70-32. The MultiPlus-II then takes account of other connected AC consumers and only uses the power that is still "left over" to charge the battery. This prevents the generator or mains connection from being overloaded (PowerControl function). The PowerAssist function adds a new dimension to the PowerControl principle. Load peaks often only occur for a limited period of time. In such cases, the MultiPlus-II immediately compensates for insufficient generator, shore power or mains power with energy from the battery. If the load is reduced, i.e. consumers are switched off, the available energy can then be used to recharge the batteries. Solar power: alternating current even in the event of a mains failure The device can be used with both off-grid and grid-connected PV systems as well as other alternative energy systems. It can be used with both solar charge controllers and grid-connected inverters. Maximum flexibility thanks to two AC outputs The main output ensures uninterrupted operation. In the event of a mains failure or an interruption in the shore/generator current, the MultiPlus-II takes over the supply to the connected loads. The switchover takes place so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic devices is guaranteed. The second output only supplies power when alternating current is available at the input of the MultiPlus-II. Consumers that must not discharge the battery, such as a water heater, can be connected to this output. Many options for system expansion The settings can be changed in a matter of minutes using the VEConfigure software (a computer or laptop and an MK3 USB interface are required) and several monitoring and control options are available: Color Control GX, Venus GX, Octo GX, CANvu GX, laptop, computer, Bluetooth (with the optional VE.Bus Smart Dongle), battery monitor, Digital Multi control panel. Remote configuration and monitoring Install a Color Control GX or other GX products to connect to the Internet. The operating data can be stored and viewed free of charge on our VRM (Victron Remote Management) website. If systems are connected to the Internet, they can be accessed remotely and settings can be changed. Scope of delivery: 1x Victron PMP242305010 Multiplus-II 24/3000/70-32A1x operating instructions

The Multiplus-II 48/3000/35-32 is a high-end device combination from Victron Energy (MPN PMP482305010) that combines classic Multiplus components with an external current sensor and integrated anti-islanding function. This extends the PowerControl and PowerAssist functions to 50 A and extends the potential range of use to ESS applications. The inverter module delivers a full 3000 W with a non-linear load and 2400 W with a linear continuous load. The 48 V battery charger is also very well proportioned with 35 A charging power and is supplemented by a 32 A transfer switch, which can be used to switch back and forth between the AC connections at lightning speed. Important features of the Multiplus-II 48/3000/35-32 PowerControl and PowerAssist increase of mains or generator power Built-in anti-islanding function and connection option for external current sensor (optional) can be used as a backup device in grid-connected systems for power supply in the event of grid failures can be used in various ESS (Energy Storage System) applications ideally suited for professional seafaring, yachts, vehicles and land-based, off-grid applications VE.Bus interface for parallel and three-phase operation, remote monitoring and system integration practically unlimited power thanks to parallel and three-phase operation can be configured on site or remotely using VEConfigure software* Technical features 3000W power with non-linear load 2400 W continuous load and 6000 W peak power for 48 V battery voltage, 32 A transfer switch and 35 A battery charger Output voltage: 230 VAC, frequency: 50 Hz Max. efficiency is 95%, protection class IP22 Always enough power thanks to PowerControl and PowerAssist A maximum mains or generator current can be set on the MultiPlus-II 48/3000/35-32. The MultiPlus-II then takes account of other connected AC consumers and only uses the power that is still "left over" to charge the battery. This prevents the generator or mains connection from being overloaded (PowerControl function). The PowerAssist function adds a new dimension to the PowerControl principle. Load peaks often only occur for a limited period of time. In such cases, the MultiPlus-II immediately compensates for insufficient generator, shore power or mains power with energy from the battery. If the load is reduced, i.e. consumers are switched off, the available energy can then be used to recharge the batteries. Solar power: alternating current even in the event of a mains failure The device can be used with both off-grid and grid-connected PV systems as well as other alternative energy systems. It can be used with both solar charge controllers and grid-connected inverters. Maximum flexibility thanks to two AC outputs The main output ensures uninterrupted operation. In the event of a mains failure or an interruption in the shore/generator current, the MultiPlus-II takes over the supply to the connected loads. The switchover takes place so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic devices is guaranteed. The second output only supplies power when alternating current is available at the input of the MultiPlus-II. Consumers that must not discharge the battery, such as a water heater, can be connected to this output. Many options for system expansion The settings can be changed in a matter of minutes using the VEConfigure software (a computer or laptop and an MK3 USB interface are required) and several monitoring and control options are available: Color Control GX, Venus GX, Octo GX, CANvu GX, laptop, computer, Bluetooth (with the optional VE.Bus Smart Dongle), battery monitor, Digital Multi control panel. Remote configuration and monitoring Install a Color Control GX or other GX products to connect to the Internet. The operating data can be stored and viewed free of charge on our VRM (Victron Remote Management) website. If systems are connected to the Internet, they can be accessed remotely and settings can be changed. Scope of delivery: 1x Victron PMP482305010 Multiplus-II 48/3000/35-32A1x operating instructions

The Multiplus-II 48/5000/70-50 is a high-end device combination from Victron Energy (MPN PMP482505010) that combines classic Multiplus components with an external current sensor and integrated anti-islanding function. This extends the PowerControl and PowerAssist functions to 100 A and extends the potential range of use to ESS applications. The inverter module delivers a full 5000 W with a non-linear load and 4000 W with a linear continuous load. The 48 V battery charger is also very well proportioned with 70 A charging power and is supplemented by a 50 A transfer switch, which can be used to switch back and forth between the AC connections at lightning speed. Important features of the Multiplus-II 48/5000/70-50 PowerControl and PowerAssist increase of mains or generator powerbuilt-in anti-islanding function and connection option for external current sensor (optional)can be used as a backup device in grid-connected systems for power supply in the event of grid failurescan be used in various ESS (Energy Storage System) applicationsideally suited for professional seafaring, yachts, vehicles and land-based, off-grid applicationsVE.Bus interface for parallel and three-phase operation, remote monitoring and system integrationpractically unlimited power thanks to parallel and three-phase operationcan be configured on site or remotely using VEConfigure software* Technical features 5000 W power with non-linear load 4000 W continuous load and 9000 W peak powerfor 48 V battery voltage, 50 A transfer switch and 70 A battery chargerOutput voltage: 230 VAC, frequency: 50 Hzmax. efficiency is 95%, protection class IP22 Always enough power thanks to PowerControl and PowerAssist A maximum mains or generator current can be set on the MultiPlus-II 48/5000/70-50. The MultiPlus-II then takes account of other connected AC consumers and only uses the power that is still "left over" to charge the battery. This prevents the generator or mains connection from being overloaded (PowerControl function). The PowerAssist function adds a new dimension to the PowerControl principle. Load peaks often only occur for a limited period of time. In such cases, the MultiPlus-II immediately compensates for insufficient generator, shore power or mains power with energy from the battery. If the load is reduced, i.e. consumers are switched off, the available energy can then be used to recharge the batteries. Solar power: alternating current even in the event of a mains failure The device can be used with both off-grid and grid-connected PV systems as well as other alternative energy systems. It can be used with both solar charge controllers and grid-connected inverters. Maximum flexibility thanks to two AC outputs The main output ensures uninterrupted operation. In the event of a mains failure or an interruption in the shore/generator current, the MultiPlus-II takes over the supply to the connected loads. The switchover takes place so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic devices is guaranteed. The second output only supplies power when alternating current is available at the input of the MultiPlus-II. Consumers that must not discharge the battery, such as a water heater, can be connected to this output. Many options for system expansion The settings can be changed in a matter of minutes using the VEConfigure software (a computer or laptop and an MK3 USB interface are required) and several monitoring and control options are available: Color Control GX, Venus GX, Octo GX, CANvu GX, laptop, computer, Bluetooth (with the optional VE.Bus Smart Dongle), battery monitor, Digital Multi control panel. Remote configuration and monitoring Install a Color Control GX or other GX products to connect to the Internet. The operating data can be stored and viewed free of charge on our VRM (Victron Remote Management) website. If systems are connected to the Internet, they can be accessed remotely and settings can be changed. Scope of delivery: 1x Victron PMP482505010 Multiplus-II 48/5000/70-50A 1x operating instructions

The Multiplus-II 24/3000/70-32 is a high-end device combination from Victron Energy (MPN PMP242305010) that combines classic Multiplus components with an external current sensor and integrated anti-islanding function. This extends the PowerControl and PowerAssist functions to 50 A and extends the potential range of use to ESS applications. The inverter module delivers a full 3000 W with a non-linear load or 2400 W with a linear continuous load. The 24 V battery charger is also very well proportioned with 70 A charging power and is supplemented by a 32 A transfer switch, which can be used to switch back and forth between the AC connections at lightning speed. Important features of the Multiplus-II 24/3000/70-32 PowerControl and PowerAssist increase mains or generator output built-in anti-islanding function and connection option for external current sensor (optional) can be used as a backup device in grid-connected systems for power supply in the event of grid failures can be used in various ESS (Energy Storage System) applications ideally suited for professional seafaring, yachts, vehicles and land-based, off-grid applications VE.Bus interface for parallel and three-phase operation, remote monitoring and system integration practically unlimited power thanks to parallel and three-phase operation can be configured on site or remotely using VEConfigure software* Technical features 3000 W power with non-linear load 2400 W continuous load and 6000 W peak power for 24 V battery voltage, 32 A transfer switch and 70 A battery charger Output voltage: 230 VAC, frequency: 50 Hz Max. efficiency is 95%, protection class IP22 Always enough power thanks to PowerControl and PowerAssist A maximum mains or generator current can be set on the MultiPlus-II 24/3000/70-32. The MultiPlus-II then takes account of other connected AC consumers and only uses the power that is still "left over" to charge the battery. This prevents the generator or mains connection from being overloaded (PowerControl function). The PowerAssist function adds a new dimension to the PowerControl principle. Load peaks often only occur for a limited period of time. In such cases, the MultiPlus-II immediately compensates for insufficient generator, shore power or mains power with energy from the battery. If the load is reduced, i.e. consumers are switched off, the available energy can then be used to recharge the batteries. Solar power: alternating current even in the event of a mains failure The device can be used with both off-grid and grid-connected PV systems as well as other alternative energy systems. It can be used with both solar charge controllers and grid-connected inverters. Maximum flexibility thanks to two AC outputs The main output ensures uninterrupted operation. In the event of a mains failure or an interruption in the shore/generator current, the MultiPlus-II takes over the supply to the connected loads. The switchover takes place so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic devices is guaranteed. The second output only supplies power when alternating current is available at the input of the MultiPlus-II. Consumers that must not discharge the battery, such as a water heater, can be connected to this output. Many options for system expansion The settings can be changed in a matter of minutes using the VEConfigure software (a computer or laptop and an MK3 USB interface are required) and several monitoring and control options are available: Color Control GX, Venus GX, Octo GX, CANvu GX, laptop, computer, Bluetooth (with the optional VE.Bus Smart Dongle), battery monitor, Digital Multi control panel. Remote configuration and monitoring Install a Color Control GX or other GX products to connect to the Internet. The operating data can be stored and viewed free of charge on our VRM (Victron Remote Management) website. If systems are connected to the Internet, they can be accessed remotely and settings can be changed. Scope of delivery: 1x Victron PMP242305010 Multiplus-II 24/3000/70-32A1x operating instructions

The Multiplus-II 48/8000/110-100 is a high-end device combination from Victron Energy (MPN PMP482805000) that combines classic Multiplus components with an external current sensor and integrated anti-islanding function. This extends the PowerControl and PowerAssist functions to 100 A and extends the potential range of use to ESS applications. The inverter module delivers a full 8000 W with a non-linear load and 6400 W with a linear continuous load. The 48 V battery charger is also very well proportioned with 110 A charging power and is supplemented by a 100 A transfer switch, which can be used to switch back and forth between the AC connections at lightning speed. Important features of the Multiplus-II 48/8000/110-100 PowerControl and PowerAssist - increase of mains or generator powerBuilt-in anti-islanding function and connection option for external current sensor (optional)can be used as a backup device in grid-connected systems for power supply in the event of grid failurescan be used in various ESS (Energy Storage System) applicationsideally suited for professional seafaring, yachts, vehicles and land-based, off-grid applicationsVE.Bus interface for parallel and three-phase operation, remote monitoring and system integrationpractically unlimited power thanks to parallel and three-phase operationcan be configured on site or remotely using VEConfigure software* Technical features 8000 W power with non-linear load 6400 W continuous load and 15000 W peak powerfor 48 V battery voltage, 100 A transfer switch and 110 A battery chargerOutput voltage: 230 VAC, frequency: 50 HzMax. efficiency is 95%, protection class IP22 Always enough power thanks to PowerControl and PowerAssist A maximum mains or generator current can be set on the MultiPlus-II 48/8000/110-100. The MultiPlus-II then takes account of other connected AC consumers and only uses the power that is still "left over" to charge the battery. This prevents the generator or mains connection from being overloaded (PowerControl function). The PowerAssist function adds a new dimension to the PowerControl principle. Load peaks often only occur for a limited period of time. In such cases, the MultiPlus-II immediately compensates for insufficient generator, shore power or mains power with energy from the battery. If the load is reduced, i.e. consumers are switched off, the available energy can then be used to recharge the batteries. Solar power: alternating current even in the event of a mains failure The device can be used with both off-grid and grid-connected PV systems as well as other alternative energy systems. It can be used with both solar charge controllers and grid-connected inverters. Maximum flexibility thanks to two AC outputs The main output ensures uninterrupted operation. In the event of a mains failure or an interruption in the shore/generator current, the MultiPlus-II takes over the supply to the connected loads. The switchover takes place so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic devices is guaranteed. The second output only supplies power when alternating current is available at the input of the MultiPlus-II. Consumers that must not discharge the battery, such as a water heater, can be connected to this output. Many options for system expansion The settings can be changed in a matter of minutes using the VEConfigure software (a computer or laptop and an MK3 USB interface are required) and several monitoring and control options are available: Color Control GX, Venus GX, Octo GX, CANvu GX, laptop, computer, Bluetooth (with the optional VE.Bus Smart Dongle), battery monitor, Digital Multi control panel. Remote configuration and monitoring Install a Color Control GX or other GX products to connect to the Internet. The operating data can be stored and viewed free of charge on our VRM (Victron Remote Management) website. If systems are connected to the Internet, they can be accessed remotely and settings can be changed. Scope of delivery: 1x Victron PMP482805000 Multiplus-II 48/8000/110-100A 1x operating instructions

The Multiplus-II 48/10000/140-100 is a high-end device combination from Victron Energy (MPN PMP483105000) that combines classic Multiplus components with an external current sensor and integrated anti-islanding function. This extends the PowerControl and PowerAssist functions to 100 A and extends the potential range of use to ESS applications. The inverter module delivers a full 10000 W with a non-linear load or 8000 W with a linear continuous load. The 48 V battery charger is also very well proportioned with 140 A charging power and is supplemented by a 100 A transfer switch, which can be used to switch back and forth between the AC connections at lightning speed. Important features of the Multiplus-II 48/10000/140-100 PowerControl and PowerAssist increase of mains or generator powerbuilt-in anti-islanding function and connection option for external current sensor (optional)can be used as a backup device in grid-connected systems for power supply in the event of grid failurescan be used in various ESS (Energy Storage System) applicationsideally suited for professional seafaring, yachts, vehicles and land-based, off-grid applicationsVE.Bus interface for parallel and three-phase operation, remote monitoring and system integrationpractically unlimited power thanks to parallel and three-phase operationcan be configured on site or remotely using VEConfigure software* Technical features 10000 W power with non-linear load 8000 W continuous load and 18000 W peak powerfor 48 V battery voltage, 100 A transfer switch and 140 A battery chargerOutput voltage: 230 VAC, frequency: 50 HzMax. efficiency is 95%, protection class IP22 Always enough power thanks to PowerControl and PowerAssist A maximum mains or generator current can be set on the MultiPlus-II 48/10000/140-100. The MultiPlus-II then takes account of other connected AC consumers and only uses the power that is still "left over" to charge the battery. This prevents the generator or mains connection from being overloaded (PowerControl function). The PowerAssist function adds a new dimension to the PowerControl principle. Load peaks often only occur for a limited period of time. In such cases, the MultiPlus-II immediately compensates for insufficient generator, shore power or mains power with energy from the battery. If the load is reduced, i.e. consumers are switched off, the available energy can then be used to recharge the batteries. Solar power: alternating current even in the event of a mains failure The device can be used with both off-grid and grid-connected PV systems as well as other alternative energy systems. It can be used with both solar charge controllers and grid-connected inverters. Maximum flexibility thanks to two AC outputs The main output ensures uninterrupted operation. In the event of a mains failure or an interruption in the shore/generator current, the MultiPlus-II takes over the supply to the connected loads. The switchover takes place so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic devices is guaranteed. The second output only supplies power when alternating current is available at the input of the MultiPlus-II. Consumers that must not discharge the battery, such as a water heater, can be connected to this output. Many options for system expansion The settings can be changed in a matter of minutes using the VEConfigure software (a computer or laptop and an MK3 USB interface are required) and several monitoring and control options are available: Color Control GX, Venus GX, Octo GX, CANvu GX, laptop, computer, Bluetooth (with the optional VE.Bus Smart Dongle), battery monitor, Digital Multi control panel. Remote configuration and monitoring Install a Color Control GX or other GX products to connect to the Internet. The operating data can be stored and viewed free of charge on our VRM (Victron Remote Management) website. If systems are connected to the Internet, they can be accessed remotely and settings can be changed. Scope of delivery: 1x Victron PMP483105000 Multiplus-II 48/10000/140-100A 1x operating instructions

The Multiplus-II 24/5000/120-50A is a high-end device combination from Victron Energy (MPN PMP242505010) that combines classic Multiplus components with an external current sensor and integrated anti-islanding function. This extends the PowerControl and PowerAssist functions to 100 A and extends the potential range of use to ESS applications. The inverter module delivers a full 5000 W with a non-linear load and 4000 W with a linear continuous load. The 24 V battery charger is also very well proportioned with 120 A charging power and is supplemented by a 50 A transfer switch, which can be used to switch back and forth between the AC connections at lightning speed. Important features of the MultiPlus-II 24/5000/120-50 PowerControl and PowerAssist increase of mains or generator powerBuilt-in anti-islanding function and connection option for external current sensor (optional)can be used as a backup device in grid-connected systems for power supply in the event of grid failurescan be used in various ESS (Energy Storage System) applicationsideally suited for professional seafaring, yachts, vehicles and land-based, off-grid applicationsVE.Bus interface for parallel and three-phase operation, remote monitoring and system integrationpractically unlimited power thanks to parallel and three-phase operationCan be configured on site or remotely using VEConfigure software Technical features 5000 W power with non-linear load 4000 W continuous load and 9000 W peak powerfor 24 V battery voltage, 50 A transfer switch and 120 A battery chargerOutput voltage: 230 VAC, frequency: 50 HzMax. efficiency is 95%, protection class IP22Note: Not standardized according to EN 50-549Always enough power thanks to PowerControl and PowerAssist A maximum mains or generator current can be set on the MultiPlus-II 24/5000/120-50. The MultiPlus-II then takes account of other connected AC consumers and only uses the power that is still "left over" to charge the battery. This prevents the generator or mains connection from being overloaded (PowerControl function). The PowerAssist function adds a new dimension to the PowerControl principle. Load peaks often only occur for a limited period of time. In such cases, the MultiPlus-II immediately compensates for insufficient generator, shore power or mains power with energy from the battery. If the load is reduced, i.e. consumers are switched off, the available energy can then be used to recharge the batteries. Solar power: alternating current even in the event of a mains failure The device can be used with both off-grid and grid-connected PV systems as well as other alternative energy systems. It can be used with both solar charge controllers and grid-connected inverters. Maximum flexibility thanks to two AC outputs The main output ensures uninterrupted operation. In the event of a mains failure or an interruption in the shore/generator current, the MultiPlus-II takes over the supply to the connected loads. The switchover takes place so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic devices is guaranteed. The second output only supplies power when alternating current is available at the input of the MultiPlus-II. Consumers that must not discharge the battery, such as a water heater, can be connected to this output. Many options for system expansion The settings can be changed in a matter of minutes using the VEConfigure software (a computer or laptop and an MK3 USB interface are required) and several monitoring and control options are available: Color Control GX, Venus GX, Octo GX, CANvu GX, laptop, computer, Bluetooth (with the optional VE.Bus Smart Dongle), battery monitor, Digital Multi control panel. Remote configuration and monitoring Install a Color Control GX or other GX products to connect to the Internet. The operating data can be stored and viewed free of charge on our VRM (Victron Remote Management) website. If systems are connected to the Internet, they can be accessed remotely and settings can be changed. Scope of delivery: 1x Victron PMP242505010 Multiplus-II 24/5000/120-50A 1x operating instructions