The Victron Battery-Protect BP-220 (MPN BPR122022000) disconnects the battery from the less important loads before it is completely discharged (which would damage it) or before it no longer has sufficient energy to start the engine etc.. In addition, the BP series has overvoltage protection, which switches off the load at 16V or 32V battery voltage and protects it from damage. The BP supports AGM, lead-acid, gel and lithium batteries.6 different switch-off thresholds can be setThe Battery Protect is very flexible and can be set to different cut-off voltages. The following cut-off thresholds can be activated on the device: 10.5V / 21V, 10V / 20V, 9.5V / 19V, 11.25V / 22.5V, 11.5V / 23V, 11.8V 23.6VIn addition, there are different switch-on thresholds that can be selected for most switch-off thresholds. This makes this device the perfect protective device for your battery and thus ensures maximum service life, as most voltage converters or charge regulators have undervoltage protection, but this only intervenes at fairly low values, which are usually in the range of 10.5V / 21V. The higher this switch-off threshold is, the longer you will be able to enjoy your batteries, which are generally quite cost-intensive.Selecting the cut-off thresholdDepending on the battery type, different minimum battery voltages apply which must be adhered to in order not to damage the battery. For AGM/gel batteries, we recommend setting the Batteryprotect to 11.5V switch-off threshold. For lithium batteries (LifePo4), 12.0V cut-off threshold is recommended. Depending on the intended use of the battery, it may be necessary to change these limits. The manufacturers also provide different specifications for their batteries. Therefore, always ask the battery manufacturer which cut-off threshold is the right one for your battery!Essential product features summarizedFor 12V and 24V batteries with automatic detection of the voltage range of the battery bank6 different cut-off voltages selectable220A maximum continuous currentSimple programming and status display of settings via seven-segment displayExtra mode for lithium batteries - in this mode, the BP can be controlled by the VE.Bus BMSVery low power consumptionExplosion protection through integrated MOSFET switches that replace the relays and thus reduce the risk of sparking to zeroIntegrated alarm outputOutput for delayed alarmThe alarm output is activated when the battery voltage falls below the preset value for shutdown for more than 12 seconds. Switching on the motor therefore does not activate the alarm. The alarm output is a short-circuit protected open collector output connected to the negative (minus) rail. Max. Current 50 mA. The alarm output is normally used to activate an audible signal, an LED or a relay.Load disconnection and reconnection delayThe load is switched off 90 seconds after the alarm is activated. If the battery voltage rises again to the threshold value for connection within this period (after the motor has been started, for example), the load is not switched off. The load is reconnected 30 seconds after the battery voltage has exceeded the specified voltage value for reconnection.Scope of delivery:1x Victron BPR122022000 BP-220 Battery protection 220A 12V 24V1x operating instructions

The Smart BatteryProtect 48/100 from Victron Energy (MPN BPR110048000) offers solid battery protection for 48 V batteries of various types. Compared to the previous series, the Smart version has an integrated Bluetooth module that connects the Smart BatteryProtect (SBP 48/100) to a smartphone or tablet. This allows you to program all the required switch-on/switch-off thresholds or set the appropriate value from 9 predefined thresholds.The BatteryProtect 48/100 can also be used as a charge interrupter between the battery charger and a lithium battery. A wide operating voltage range of 24 - 70 V makes the device universally applicable. The option of connecting an external switch or alarm to the BatteryProtect makes the SBP 48/100 Smart the perfect battery monitor.Performance features of the Smart BatteryProtect 48/100100 A maximum switching capacityFor 48 V batteries with automatic detection of the voltage range of the battery bankExplosion protection thanks to integrated MOSFET switches, which replace the relays and thus reduce the risk of sparking to zeroIntegrated Bluetooth module, can be switched off as requiredFreely programmable switch-on and switch-off thresholds, easily and wirelessly via the VictronConnect appalternative programming and status display of settings possible via seven-segment displayintegrated alarm output, 9 predefined threshold values selectablean external alarm, an LED or a relay can be connected to the alarm outputthe load shedding of the BP can be controlled via a relay by external events that cannot be programmed in this wayOutput for delayed alarmThe alarm output is activated if the battery voltage falls below the preset value for switch-off for more than 12 seconds. Switching on the motor therefore does not activate the alarm. The alarm output is a short-circuit protected open collector output connected to the negative (minus) rail. Max. Current 50 mA. The alarm output is normally used to activate an audible signal, an LED or a relay.Solid battery protection for every battery typeThanks to its wide range of configuration options, the Smart SBP 48/100 is the perfect protective device for your battery and thus ensures maximum service life, because although most voltage converters or charge controllers have undervoltage protection, this only takes effect at fairly low values. The higher this switch-off threshold is, the longer you will be able to enjoy your batteries, which are generally quite cost-intensive.Selecting the cut-off thresholdDepending on the battery type, there are different minimum battery voltages that must be adhered to in order not to damage the battery. For AGM/gel batteries, we recommend setting the Batteryprotect to 11.5V switch-off threshold. For lithium batteries (LifePo4), 12.0V cut-off threshold is recommended. Depending on the intended use of the battery, it may be necessary to change these limits. The manufacturers also provide different specifications for their batteries. Therefore, always ask the battery manufacturer which cut-off threshold is the right one for your battery!Scope of delivery:1x Victron Energy BPR110048000 Smart BatteryProtect SBP 48/100 100A1x operating instructions

The Smart BatteryProtect 12V/24V-100A from Victron Energy (MPN BPR110022000) offers solid battery protection for 12V and 24V batteries of various types. Compared to the previous series, the Smart version has an integrated Bluetooth module that connects the Smart BatteryProtect (BP-100) to a smartphone or tablet. This allows you to program all the required switch-on/switch-off thresholds or set the appropriate value from 9 predefined thresholds.The BatteryProtect 12/24V can also be used as a charge interrupter between the battery charger and a lithium battery. A wide operating voltage range of 6-35 V makes the device universally applicable. The option of connecting an external switch or alarm to the BatteryProtect makes the BP-100 Smart the perfect battery monitor.Features of the Smart BatteryProtect 12/24V-100A100A maximum switching capacityFor 12V and 24V batteries with automatic detection of the voltage range of the battery bankExplosion protection thanks to integrated MOSFET switches, which replace the relays and thus reduce the risk of sparking to zeroIntegrated Bluetooth module, can be switched off as requiredFreely programmable switch-on and switch-off thresholds, easily and wirelessly via the VictronConnect appalternative programming and status display of settings possible via seven-segment displayintegrated alarm output, 9 predefined threshold values selectablean external alarm, an LED or a relay can be connected to the alarm outputthe load shedding of the BP can be controlled via a relay by external events that cannot be programmed in this wayOutput for delayed alarmThe alarm output is activated if the battery voltage falls below the preset value for switch-off for more than 12 seconds. Switching on the motor therefore does not activate the alarm. The alarm output is a short-circuit protected open collector output connected to the negative (minus) rail. Max. Current 50 mA. The alarm output is normally used to activate an audible signal, an LED or a relay.Solid battery protection for every battery typeThanks to its wide range of configuration options, the Smart BP-100 is the perfect protective device for your battery and thus ensures maximum service life, because although most voltage converters or charge controllers have undervoltage protection, this only intervenes at fairly low values, which are usually in the range of 10.5V / 21V. The higher this switch-off threshold is, the longer you will be able to enjoy your batteries, which are generally quite cost-intensive.Selecting the cut-off thresholdDepending on the battery type, different minimum battery voltages apply which must be adhered to in order not to damage the battery. For AGM/gel batteries, we recommend setting the Batteryprotect to 11.5V switch-off threshold. For lithium batteries (LifePo4), 12.0V cut-off threshold is recommended. Depending on the intended use of the battery, it may be necessary to change these limits. The manufacturers also provide different specifications for their batteries. Therefore, always ask the battery manufacturer which cut-off threshold is the right one for your battery!Scope of delivery:1x Victron Energy BPR110022000 Smart BatteryProtect 12/24V 100A1x operating instructions

The Smart BatteryProtect 12/24V-65A from Victron Energy (MPN BPR065022000) offers solid battery protection for 12V and 24V batteries of various types. Compared to the previous series, the Smart version has an integrated Bluetooth module that connects the Smart BatteryProtect (BP-65) to a smartphone or tablet. This allows you to program all the required switch-on/switch-off thresholds or set the appropriate value from 9 predefined thresholds.The BatteryProtect 12/24V can also be used as a charge interrupter between the battery charger and a lithium battery. A wide operating voltage range of 6-35 V makes the device universally applicable. The option of connecting an external switch or alarm to the BatteryProtect makes the BP-65 Smart the perfect battery monitor.Features of the Smart BatteryProtect 12V/24V-65A65A maximum switching capacityFor 12V and 24V batteries with automatic detection of the voltage range of the battery bankExplosion protection thanks to integrated MOSFET switches, which replace the relays and thus reduce the risk of sparking to zeroIntegrated Bluetooth module, can be switched off as requiredFreely programmable switch-on and switch-off thresholds, easily and wirelessly via the VictronConnect appalternative programming and status display of settings possible via seven-segment displayintegrated alarm output, 9 predefined threshold values selectablean external alarm, an LED or a relay can be connected to the alarm outputthe load shedding of the BP can be controlled via a relay by external events that cannot be programmed in this wayOutput for delayed alarmThe alarm output is activated if the battery voltage falls below the preset value for switch-off for more than 12 seconds. Switching on the motor therefore does not activate the alarm. The alarm output is a short-circuit protected open collector output connected to the negative (minus) rail. Max. Current 50 mA. The alarm output is normally used to activate an audible signal, an LED or a relay.Solid battery protection for every battery typeThanks to its wide range of configuration options, the Smart BP-65 is the perfect protective device for your battery and thus ensures maximum service life, because although most voltage converters or charge regulators have undervoltage protection, this only intervenes at fairly low values, which are usually in the range of 10.5V / 21V. The higher this switch-off threshold is, the longer you will be able to enjoy your batteries, which are generally quite cost-intensive.Selecting the cut-off thresholdDepending on the battery type, different minimum battery voltages apply which must be adhered to in order not to damage the battery. For AGM/gel batteries, we recommend setting the Batteryprotect to 11.5V switch-off threshold. For lithium batteries (LifePo4), 12.0V cut-off threshold is recommended. Depending on the intended use of the battery, it may be necessary to change these limits. The manufacturers also provide different specifications for their batteries. Therefore, always ask the battery manufacturer which cut-off threshold is the right one for your battery!Scope of delivery:1x Victron Energy BPR065022000 Smart BatteryProtect 12/24V 65A1x operating instructions

The Victron Battery-Protect BP-100 (MPN BPR000100400) disconnects the battery from the less important consumers before it is completely discharged (which would damage it) or before it no longer has sufficient energy to start the engine etc.. In addition, the BP series has overvoltage protection, which switches off the load at 16V or 32V battery voltage and protects it from damage. The BP supports AGM, lead-acid, gel and lithium batteries. 6 different switch-off thresholds can be setThe Battery Protect is very flexible and can be set to different cut-off voltages. The following cut-off thresholds can be activated on the device: 10.5V / 21V, 10V / 20V, 9.5V / 19V, 11.25V / 22.5V, 11.5V / 23V, 11.8V 23.6V In addition, there are different switch-on thresholds that can be selected for most switch-off thresholds. This makes this device the perfect protective device for your battery and thus ensures maximum service life, as most voltage converters or charge regulators have undervoltage protection, but this only intervenes at fairly low values, which are usually in the range of 10.5V / 21V. The higher this switch-off threshold is, the longer you will be able to enjoy your batteries, which are generally quite cost-intensive. Selecting the cut-off threshold Depending on the battery type, different minimum battery voltages apply which must be adhered to in order not to damage the battery. For AGM/gel batteries, we recommend setting the Batteryprotect to 11.5V switch-off threshold. For lithium batteries (LifePo4), 12.0V cut-off threshold is recommended. Depending on the intended use of the battery, it may be necessary to change these limits. The manufacturers also provide different specifications for their batteries. Therefore, always ask the battery manufacturer which cut-off threshold is the right one for your battery! Essential product features summarized For 12V and 24V batteries with automatic detection of the voltage range of the battery bank 6 different cut-off voltages selectable 100A maximum continuous current Simple programming and status display of settings via seven-segment display Extra mode for lithium batteries - in this mode, the BP can be controlled by the VE.Bus BMS Very low power consumption Explosion protection through integrated MOSFET switches that replace the relays and thus reduce the risk of sparking to zero Integrated alarm output Output for delayed alarm The alarm output is activated when the battery voltage falls below the preset value for shutdown for more than 12 seconds. Switching on the motor therefore does not activate the alarm. The alarm output is a short-circuit protected open collector output connected to the negative (minus) rail. Max. Current 50 mA. The alarm output is normally used to activate an audible signal, an LED or a relay. Load disconnection and reconnection delay The load is switched off 90 seconds after the alarm is activated. If the battery voltage rises again to the threshold value for reconnection within this period (after the engine has been started, for example), the load is not switched off. 30 seconds after the battery voltage has exceeded the specified voltage value for reconnection, the load is reconnected. Scope of delivery:1x Victron BPR000100400 BP-100 battery protection 100A 12V 24V1x instruction manual

The SmartShunt 500A IP65 from Victron Energy (MPN SHU065150050) is an IP65 waterproof all-in-one battery monitor. It connects to the VictronConnect app on your phone (or tablet) via Bluetooth and you can conveniently read out all monitored battery parameters, such as state of charge, remaining runtime, history information and much more. Settings can also be changed easily. Alternatively, the SmartShunt can be connected and read by a GX device. The SmartShunt is connected to a GX device via a VE.Direct cable. The SmartShunt is a good alternative for a BMV battery monitor, especially for systems where battery monitoring is required but less cabling and clutter is desired.This IP65 protected variant is ideal for use on boats or in marine applications. Features Equipped with BluetoothConveniently check battery parameters on your smartphone or tabletConnection to GX device possibleAdditional input for further monitoring optionsUncomplicated installation

The VOTRONIC Battery Protector 40 is connected between the supply battery and the consumer and is suitable for all lead-acid battery types (acid, gel, AGM) and makes. They protect the battery from dangerous deep discharge as well as the consumers and equipment from undervoltage and overvoltage and, controlled by an external switch, can also serve as a remote-controlled battery master switch. The reset to normal operation takes place automatically as soon as the voltage has risen again, e.g. to 12.5 V, due to battery recovery or brief charging. The switch-off can also be canceled manually using the "EMERGENCY ON" function. The Battery Protector 40 can be operated remotely via the "Sensor +" terminal using a simple switch (1-pole ON / OFF). This makes it a powerful battery main switch. The EMERGENCY ON function can also be operated remotelyImportant product features Switching current 40 A, briefly overloadable up to 60 A, externally visible switching status display EMERGENCY STOP function via switch on the device, can also be operated remotely via external switch Automatic reset as soon as the battery voltage returns to the normal range (charging) Separate sensor cable and switching thresholds with hysteresis and timer functions for trouble-free operation Bistable power relay, very low power consumption, less than 3 mA (according to EN 13976) No self-consumption when switched off via external switch, e.g. remote control as main battery switch Solid screw terminals for battery and load cable cross-sections up to 10 mm² "Motor" version with higher switch-off thresholds maintains the starting capability of emergency vehicles with only one battery circuit in accordance with DIN EN 1789 Technical data MPN 3075 Operating voltage: 12V Switching current (continuous/short): 40A/60A Switching threshold undervoltage: 10.7V Undervoltage reset point: 12.8V Overvoltage protection (off/on): 15.5V / 15V Weight: 97 grams

The VOTRONIC 6075 Battery Protector 40 24 is connected between the supply battery and the consumer and is suitable for all lead-acid battery types (acid, gel, AGM) and makes. They protect the battery from dangerous deep discharge as well as the consumers and equipment from undervoltage and overvoltage and, controlled by an external switch, can also serve as a remote-controlled battery master switch The reset to normal operation takes place automatically as soon as the voltage has risen again, e.g. to 25 V, due to battery recovery or brief charging. The switch-off can also be canceled manually using the "EMERGENCY ON" function. The Battery Protector 40 can be operated remotely via the "Sensor +" terminal using a simple switch (1-pole ON / OFF). This makes it a powerful battery main switch. The EMERGENCY ON function can also be operated remotely Important product features Switching current 40 A, briefly overloadable up to 60 A, externally visible switching status displayEMERGENCY STOP function via switch on the device, can also be operated remotely via external switchAutomatic reset as soon as the battery voltage returns to the normal range (charging)Separate sensor cable and switching thresholds with hysteresis and timer functions for trouble-free operationBistable power relay, very low power consumption, less than 3 mA (according to EN 13976)No self-consumption when switched off via external switch, e.g. remote control as main battery switchSolid screw terminals for battery and load cable cross-sections up to 10 mm²"Motor" version with higher switch-off thresholds maintains the starting capability of emergency vehicles with only one battery circuit in accordance with DIN EN 1789Technical data MPN 6075Operating voltage: 24VSwitching current (continuous/short): 40A/60ASwitching threshold undervoltage: 21.4VUndervoltage reset point: 25VOvervoltage protection (off/on): 31V/30VWeight: 97 gramsDimensions (W x H x D) 90 x 38 x 60 mm

This battery monitor protects your car battery from deep discharge by switching off consumers such as coolers, heaters, radios, televisions, etc. in good time. It switches on again automatically when the normal voltage returns. The cut-off voltage is adjustable: approx. 10.4 - 13.3 V.

The VOTRONIC Battery Protector 40 Motor is connected between the supply battery and the consumer and is suitable for all lead-acid battery types (acid, gel, AGM) and makes. They protect the battery from dangerous deep discharge as well as the consumers and equipment from undervoltage and overvoltage and, controlled by an external switch, can also serve as a remote-controlled battery master switch. Compared to the "normal" Battery Protector 40, the motor version switches to undervoltage at 11.8V. The reset to normal operation takes place automatically as soon as the voltage has risen again, e.g. to 12.5 V, due to battery recovery or brief charging. The switch-off can also be canceled manually using the "EMERGENCY ON" function. The Battery Protector 40 can be operated remotely via the "Sensor +" terminal using a simple switch (1-pole ON / OFF). This makes it a powerful battery main switch. The EMERGENCY ON function can also be operated remotely Important product features Switching current 40 A, briefly overloadable up to 60 A, externally visible switching status displayEMERGENCY STOP function via switch on the device, can also be operated remotely via external switchAutomatic reset as soon as the battery voltage returns to the normal range (charging)Separate sensor cable and switching thresholds with hysteresis and timer functions for trouble-free operationBistable power relay, very low power consumption, less than 3 mA (according to EN 13976)No self-consumption when switched off via external switch, e.g. remote control as main battery switchSolid screw terminals for battery and load cable cross-sections up to 10 mm²"Motor" version with higher switch-off thresholds maintains the starting capability of emergency vehicles with only one battery circuit in accordance with DIN EN 1789Technical data MPN 3075Operating voltage: 12VSwitching current (continuous/short): 40A/60ASwitching threshold undervoltage: 11.8VUndervoltage reset point: 12.8VOvervoltage protection (off/on): 15.5V / 15VWeight: 97 grams

Displays the current charge status of a 12 V battery in 5 stages with 3 LEDs. This makes it easy to check the battery and prevent deep discharge. It also checks whether the battery is OK and whether it is accepting the full charging voltage from the charger. (If the battery monitor is connected to the battery during the charging process). The battery monitor is designed to monitor a battery in a closed, active circuit. Extremely low self-consumption of less than 4.9 mA!