Effective battery charging and monitoring for motorhomes, caravans, boats and self-sufficient solar systems! How much charge does my on-board battery actually have left? Is the battery really full? Why is energy being drawn from the battery despite consumers being switched off?The VOTRONIC LCD battery computer S answers these questions to the exact percentage (%) and ampere hour (Ah). At the touch of a button, it provides comprehensive information on the current charge status of the battery, the battery currents flowing and the voltage level of the battery.The device is in constant contact with "its battery" and thus registers and evaluates all battery actions. All charging and discharging currents are meticulously counted, battery size, self-discharge, battery load etc. are taken into account using programmed characteristic curve fields. The remaining battery capacity is then calculated from the measured values and the battery size. The result is the correct display of the state of charge (remaining capacity, residual charge) of the on-board battery as a numerical value in ampere hours ("Ah") and in percent ("%") as well as a clear fill level bar, like a fuel gauge.The LCD battery computer S is suitable for all battery types (acid, gel, AGM, lithium adjustable) with 12V and 24 V battery voltage. Of course, the current battery voltage ("V") and the current battery current ("A") are also available in the display. Discharge currents (consumers) are indicated by a minus sign. Charging currents are also indicated by a clearly legible "Charge" symbol. Independently of this, there is a further display option for the voltage of a second battery, e.g. for monitoring the vehicle's starter battery.A plug-in connection cable connects the display completely to a robust precision measuring resistor (shunt), which is connected directly to the negative terminal of the on-board battery and at which the voltages and currents of the battery are recorded.The following values are measured: On-board battery voltage Battery voltage starter battery Battery current (charging ="+"; discharging ="-") Load from consumers Battery capacity "Ah" (remaining charge in ampere hours) Battery capacity "%" (remaining charge in percent) Switching output (freely programmable) Flashing warning display in the event of undervoltage or overvoltage Can I also program the battery computer? The LCD battery computer S has a freely programmable switching output for control, monitoring and warning purposes, e.g. to automatically switch loads or issue a warning depending on the charge status of the on-board battery (0-100%). On and off switching points can be set freely and independently of each other in %, enabling any number of switching functions. They can also be overridden manually at any time at the touch of a button. Application example: Automatic protection of the battery against harmful deep discharge, the consumers are switched off exactly according to the state of charge, e.g. at less than 25% state of charge How is the battery computer connected? A plug-in connection cable connects the LCD display completely to a robust precision measuring resistor (shunt), which is connected directly to the negative terminal of the on-board battery and at which the battery voltages and currents are recorded. The switching output for connecting signal transmitters or powerful switching relays is also located here. Can I also use a different shunt? The display is supplied with a suitable measuring shunt; the devices are matched to the measuring shunts included in the scope of delivery and cannot be operated in conjunction with other measuring shunts or interchanged! Technical data Article no.: 1269 Measuring shunt: 400A LiFePO4 battery voltage: 12.8-13.2 V / 25.6-6.4 V Current consumption: 8mA Battery nominal capacity, adjustable: 50-2000 Ah Current consumption of the lighting (can be switched off): 60 mA Current measuring range shunt / continuous: 400A Current measuring range shunt / 15 min.: 600A Current measuring range shunt / 7 min.: 1800A Test mark: CE, E-test (EMC/vehicle directive) Dimensions: W80 x H85 x D24 mm Installation dimensions: W66 x H72 x D22 mm Shunt dimensions: W135 x H30 x D42mm Display weight. 55g Weight of smart shunt: 245g Scope of delivery: Display unit Measuring shunt 400A Smart-Shunt cover Connection cable 5m long Ground strap Fixing screws Instruction manual Drilling template

Effective battery charging and monitoring for motorhomes, caravans, boats and self-sufficient solar systems! How much charge does my on-board battery actually have left? Is the battery really full? Why is energy being drawn from the battery despite consumers being switched off?The VOTRONIC LCD battery computer S answers these questions to the exact percentage (%) and ampere hour (Ah). At the touch of a button, it provides comprehensive information on the current charge status of the battery, the battery currents flowing and the voltage level of the battery.The device is in constant contact with "its battery" and thus registers and evaluates all battery actions. All charging and discharging currents are meticulously counted, battery size, self-discharge, battery load etc. are taken into account using programmed characteristic curve fields. The remaining battery capacity is then calculated from the measured values and the battery size. The result is the correct display of the state of charge (remaining capacity, residual charge) of the on-board battery as a numerical value in ampere hours ("Ah") and in percent ("%") as well as a clear fill level bar, like a fuel gauge.The LCD battery computer S is suitable for all battery types (acid, gel, AGM, lithium adjustable) with 12V and 24 V battery voltage. Of course, the current battery voltage ("V") and the current battery current ("A") are also available in the display. Discharge currents (consumers) are indicated by a minus sign. Charging currents are also indicated by a clearly legible "Charge" symbol. Independently of this, there is a further display option for the voltage of a second battery, e.g. for monitoring the vehicle's starter battery.A plug-in connection cable connects the display completely to a robust precision measuring resistor (shunt), which is connected directly to the negative terminal of the on-board battery and at which the voltages and currents of the battery are recorded.The following values are measured: On-board battery voltage Battery voltage starter battery Battery current (charging ="+"; discharging ="-") Load from consumers Battery capacity "Ah" (remaining charge in ampere hours) Battery capacity "%" (remaining charge in percent) Switching output (freely programmable) Flashing warning display in the event of undervoltage or overvoltage Can I also program the battery computer? The LCD battery computer S has a freely programmable switching output for control, monitoring and warning purposes, e.g. to automatically switch loads or issue a warning depending on the charge status of the on-board battery (0-100%). On and off switching points can be set freely and independently of each other in %, enabling any number of switching functions. They can also be overridden manually at any time at the touch of a button. Application example: Automatic protection of the battery against harmful deep discharge, the consumers are switched off exactly according to the state of charge, e.g. at less than 25% state of charge How is the battery computer connected? A plug-in connection cable connects the LCD display completely to a robust precision measuring resistor (shunt), which is connected directly to the negative terminal of the on-board battery and to which the voltages and currents of the battery are recorded. The switching output for connecting signal transmitters or powerful switching relays is also located here. Can I also use a different shunt? The display is supplied with a suitable measuring shunt; the devices are matched to the measuring shunts included in the scope of delivery and cannot be operated in conjunction with other measuring shunts or interchanged! Technical data: Measuring shunt: 100A LiFePO4 battery voltage: 12.8-13.2 V / 25.6-6.4 V Current consumption: 8mA Battery nominal capacity, adjustable: 50-2000 Ah Current consumption of the lighting (can be switched off): 60 mA Current measuring range shunt / continuous: 100A Current measuring range shunt / 15 min.: 150A Current measuring range shunt / 7 min.: 450A Test mark: CE, E-test (EMC/vehicle directive) Dimensions: W80 x H85 x D24 mm Installation dimensions: W66 x H72 x D22 mm Shunt dimensions: W135 x H30 x D42mm Display weight. 55g Weight of smart shunt: 240g Scope of delivery: Display unit Measuring shunt 100A Smart shunt cover Connection cable 5m long Ground strap Fixing screws Instruction manual Drilling template

The SmartShunt 1000A IP65 from Victron Energy (MPN SHU065210050) is an IP65 waterproof all-in-one battery monitor. It connects to the VictronConnect app on your phone (or tablet) via Bluetooth and you can conveniently read out all monitored battery parameters, such as state of charge, remaining runtime, history information and much more. Settings can also be changed easily. Alternatively, the SmartShunt can be connected and read by a GX device. The SmartShunt is connected to a GX device via a VE.Direct cable. The SmartShunt is a good alternative for a BMV battery monitor, especially for systems where battery monitoring is required but less cabling and clutter is desired.This IP65 protected variant is ideal for use on boats or in marine applications. Features Equipped with BluetoothConveniently check battery parameters on your smartphone or tabletConnection to GX device possibleAdditional input for further monitoring optionsUncomplicated installation

The SmartShunt 2000A IP65 from Victron Energy (MPN SHU065220050) is an IP65 waterproof all-in-one battery monitor. It connects to the VictronConnect app on your phone (or tablet) via Bluetooth and you can conveniently read out all monitored battery parameters, such as state of charge, remaining runtime, history information and much more. Settings can also be changed easily. Alternatively, the SmartShunt can be connected and read by a GX device. The SmartShunt is connected to a GX device via a VE.Direct cable. The SmartShunt is a good alternative for a BMV battery monitor, especially for systems where battery monitoring is required but less cabling and clutter is desired.This IP65 protected variant is ideal for use on boats or in marine applications. Features Equipped with BluetoothConveniently check battery parameters on your smartphone or tabletConnection to GX device possibleAdditional input for further monitoring optionsUncomplicated installation

The Victron Battery Monitor as a high-precision battery monitor The Victron BMV 700 / 702 / Battery Monitor series are characterized as high-precision battery monitors. They reliably calculate the ampere hours consumed and the current state of charge of the energy storage system. At the same time, the models from the popular brand manufacturer display the remaining runtime and power consumption in watts. As the BMV-702 monitor has an additional input, the voltage of a second battery can be easily measured. Intuitive and powerful Thanks to the integrated Bluetooth Smart Dongle function, the batteries connected to the Victron BMV 700 / 702 / 702-black / 700H monitors can be monitored at any time via an Android or iOS device. This provides additional planning security in everyday life. The same applies to the intuitive handling: A quick installation menu as well as an easy-to-understand setup menu enable uncomplicated operation of the Victron Battery Monitor BMV-700 and 702 series. You can rely on Victron battery monitors A special feature of the BMV-702 is the feature for monitoring the midpoint voltage. This is usually only found in industrial battery monitors. The high-performance products from Victron display the remaining battery life regardless of the series. It is calculated based on the current discharge rate. To further simplify use, the quality products offer a visually and acoustically programmable alarm function. They also impress with an attractively high shunt capacity of up to 10,000 amps and a wide input voltage range from 9.5 V to 95 V.

With integrated BluetoothWith its built-in Bluetooth, the BMV Smart is ready for the age of the "Internet of Things" (IoT).Most other Victron Energy products also have Bluetooth. The wirelesscommunication between products simplifies the installation of systems and improves performance.performance. Download the Victron Bluetooth appUsing a smartphone or other Bluetooth-enabled device, adjust the- customize the settings,- Display all important data on one screen,- view history data and- update to the latest software when new features are available. Easy installationAll electrical connections are made using the PCB connector on the current shuntwith the PCB connector. The shunt is connected to the monitor via a standard RJ12 telephone cable. Included inIncluded in delivery: RJ 12 cable (10 m) and battery cable with fuse (2 m); no other components are required.components are required.In addition, a separate front panel for a square or round display; a safety ringfor rear mounting and screws for front mounting are also supplied. Monitoring the center voltageOne damaged cell or battery can destroy an entire large, expensive battery bank.If batteries are connected in series, the measurement of the midpoint voltage can generate awarning message can be generated in good time. Please also refer to the BMV manual, section 5.2 forfurther information.We recommend our battery balancer (BMS012201000) to extend the service life of lead-acid batteries connected in series.lead-acid batteries connected in series. Very low current consumption from the batteryCurrent consumption: 0.7 Ah per month (1 mA) at 12 V and 0.6 Ah per month (0.8 mA) at 24 VLithium-ion batteries in particular have almost no capacity left when they are discharged to the point ofdischarged until they are switched off due to low voltage.After switching off due to low voltage, the capacity reserve of a lithium-ion battery isis approximately 1 Ah per 1000 Ah of battery capacity. The battery will be damaged if the remaining reservereserve capacity is removed from the battery. A residual current of 10 mA, for example, can damage a 200 Ahbattery if the system is left in a discharged state for more than 8 days. Bistable alarm relayPrevents increased current drain in the event of an alarm. Other features- Battery voltage, current, power, ampere hours consumed and state of charge- Remaining runtime at current discharge rate- Programmable visual and audible alarm- Programmable relay to switch off non-essential loads or switch on a generator if required.switch on when required.- One 500 amp quick connect shunt and one connection kit.- Shunt capacity selectable up to 10,000 amps.- VE.Direct communication port- Stores a wide range of historical data that can be used to assess usage patterns and battery condition.can be evaluated.- Wide input voltage range: 6.5 - 70V- High current measurement resolution 10 mA (0.01 A)- Additional input for measuring voltage (of a second battery), temperature or midpoint voltagemidpoint voltage and associated alarm and relay settings.

The bmv 712 Smart from victron Energy (mpn bam030712200) is the latest battery computer in the bmv family. It provides precise data on parameters such as battery voltage, current, power, ampere hours consumed, state of charge and remaining time at the current discharge rate. The measurement resolution is very accurate and precise compared to similar products. In addition, it is equipped with an integrated Bluetooth module that allows you to access many functions and status reports of the battery computer via the free victronConnect app. Main features of the victron bmv 712 Smart battery monitor Built-in Bluetooth Module: With its built-in Bluetooth:module, the bmv Smart is already for the "Internet of Things". Meanwhile, in addition to the bmv 712, most other victron products also have integrated Bluetooth. networking, evaluation and communication has never been as convenient as it is today. Free victron Bluetooth app: The victronConnect app allows you to evaluate all victron products with vE.Direct interface. Depending on the device, numerous parameters can be read out directly via cell phone, computer or tablet. You can display all important data on one screen, adjust settings and update to the latest software. options for data logging and data export are also available. So you always know how your system is doing. Easy installation: All electrical connections are made to the current shunt using the PCB connector. The shunt is connected to the monitor via a standard RJ12 telephone cable. Included in delivery: RJ12 cable (10 m) and battery cable with fuse (2 m). No other components are required. also included is a separate front bezel for a square or round display, a safety ring for rear mounting and screws for front mounting. Huge range of functions: Numerous battery monitoring functions and generously sized electronic components on the Smart bmv's circuit board allow you to gain deep insights into the life of your battery. In addition, with the help of the bmv, you can detect and fix problems, even in larger battery banks, before damage occurs. More features of the bmv 712 battery computer Programmable visual and audible alarmProgrammable relay to switch off essential loads or switch on to a generator when neededOne 500 amp quick connect shunt and connection kitShunt capacity selectable up to 10,000 ampsvE.Direct communication portStores a wide range of history data that can be used to evaluate usage patterns and battery conditionWide input voltage range: 6.5 - 70 vHigh current measurement resolution 10 ma (0.01a)Additional input for measuring voltage (of a second battery), temperature or midpoint voltage and associated alarm and relay settings High resolution measurement data from up to 2 batteries Current ± 0.01aVoltage ± 0.01vampere-hour ± 0.1 ahState of charge (0-100%) ± 0.1%Remaining time ± 1 minTemperature (0-50°C or 30-120°F) ± 1°C/°FAccuracy of current measurement ±0.4% Low self consumption The current consumption of the bmv is only 0.7 ah per month (1 ma) at 12 v and 0.6 ah per month (0.8 ma) at 24 v. In particular, lithium-ion batteries have almost no capacity left when they are discharged to the point of shutdown due to low voltage. After shutdown due to low voltage, the reserve capacity of a lithium-ion battery is approximately 1 ah per 1000 ah of battery capacity. The battery will be damaged if the remaining reserve capacity is drawn from the battery. For example, a residual current of 10 ma can damage a 200 ah battery if the system is left in a discharged state for over 8 days. midpoint voltage monitoring One damaged cell or battery can destroy an entire large, expensive battery bank. When batteries are connected in series, measuring the midpoint voltage can provide a timely warning. Please also refer to the bmv manual, section 5.2 for more information.victron recommends the Battery Balancer (bms012201000) to maximize the life of lead-acid batteries connected in series. Scope of delivery: 1x victron bmv Smart 712, Battery Monitor1x shunt 500 a / 50 mv1x 10 meter 6 wire UTP cable with RJ12 connectors1x 2 meter battery cable with fuse1x front panel1x mounting material

The intelligent battery shunt The SmartShunt is an all-in-one battery monitor, only without a display. Your phone acts as the display. The SmartShunt connects to the VictronConnect app on your phone (or tablet) via Bluetooth and you can conveniently read out all monitored battery parameters, such as state of charge, remaining runtime, history information and much more. Alternatively, the SmartShunt can be connected and read by a GX device. The connection to the SmartShunt is made via a VE.Direct cable. The SmartShunt is a good alternative for BMV battery monitoring, especially for systems where battery monitoring is required but less cabling and clutter is desired. The SmartShunt is equipped with Bluetooth, a VE.Direct port and a connection that can be used for the following: Monitoring a second battery, midpoint monitoring or a temperature sensor.

The Votronic 5749 VPC Power Control Jupiter 100 is part of an innovative series of combination panels that have been specially developed for installation in motorhomes. It combines the functions of the Merkur 5744 and Terra 5741 models and also has a lot more to offer as it combines a solar computer, battery computer and water management in one device. The 400 is the largest version of the new Multi-Panel series from Votronic. It differs from the 200 and 100 versions only in the maximum battery current that can be measured with the Jupiter Panel.The Jupiter series is currently the benchmark for measuring and display devices in the motorhome sector. No other panel offers such a wide range of functions, measurement and display options. Jupiter is also significantly cheaper than buying all the devices included individually.Integrated solar computerThe solar computer of the Jupiter combi panel corresponds in performance and function to the Solar-Computer S. The solar display is compatible with most Votronic charge controllers and the Triple series. Among other things, it shows the current solar power in W, the current solar current in A, the charged solar capacity in Ah and the charged solar energy in kWh. The solar computer provides a comprehensive picture of the current performance of your motorhome solar system.Integrated battery computer incl. smart shunt and ground strapAlso corresponds in terms of performance to the single device Battery Computer 400 S (manufacturer number 1269), which is also available as a 200 and 100A version. The Votronic battery computer provides a comprehensive impression of the condition of your starter and board battery and offers numerous functions.Microprocessor-controlled, the following values are measured, calculated and displayed: max. battery current: 400A On-board battery voltage 7 to 32 V (volts). Internal measurement resolution 0.1 V Allows conclusions to be drawn about the battery behavior under different loads and is used for functional checks, e.g. of the charger, solar system, alternator, etc. Flashing warning display in the event of overvoltage Battery current (charge/discharge) +/- 0 to max. +/- 1800 A, internal measurement resolution 0.1 A Checking the discharge currents (load) by consumers, indicated by a "-" sign, control of charging currents, indicated by a "Charge" sign Battery capacity (Ah and %) Remaining charge from 0 Ah / 0% (empty) to nominal capacity max. 2000 Ah / 100% (full) Battery voltage 2nd battery (e.g. starter battery), 7 to 32 V (volts), internal measurement resolution 0.1 V Switching output freely programmable and tactile (PNP, plus potential 12V / 24V, max. 0.5A) incl. remaining run indicator Integrated level indicator for water tanksThe third important highlight of the Jupiter 100 is the level indicator for the fresh and waste water tanks. Together with the 16A switch for the fresh water pump, water management can also be implemented via the Jupiter combi panel.Other important features Voltage display for the starter battery Potential-free switching output for an external relay with freely programmable switching thresholds (% residual capacity) as deep discharge protection and main switch Indoor and outdoor thermometer incl. 1 indoor and 1 outdoor sensor Clock in 24-hour format Double USB charging socket (5 V/2.5 A) Simple, intuitive operation Important technical data Simple, intuitive operation Compact, simple installation low installation depth, low power consumption for 12 V or 24 V batteries Display dimensions: 200x65x30 mm Installation dimensions: 185x57x24 mm Weight without smart shunt: only 200g Scope of delivery:1x Votronic 5749 VPC Jupiter 400 Multi-Panel1x operating instructions1x temperature sensor for indoor use1x temperature sensor for outside1x Smart measuring shunt for connecting the battery computer2x 5m connection cables1x ground strap matched to the performance of the battery computer

Smarte Batterieüberwachung Der SmartShunt 500A von Victron Energy (MPN SHU050150050) ist ein All-in-one-Batteriewächter. Er verbindet sich über Bluetooth mit der VictronConnect App auf Ihrem Telefon (oder Tablet) und Sie können alle überwachten Batterieparameter, wie Ladezustand, Restlaufzeit, Verlaufsinformationen und vieles mehr bequem auslesen. Auch Einstellungen lassen sich darüber einfach verändern. Alternativ kann der SmartShunt angeschlossen und von einem GX-Gerät gelesen werden. Der Anschluss an den SmartShunt erfolgt über ein VE.Direct-Kabel. Der SmartShunt ist eine gute Alternative für einen BMV-Batteriewächter, insbesondere für Systeme, bei denen eine Batterieüberwachung erforderlich ist, aber weniger Verkabelung und Unordnung gewünscht wird. Eigenschaften Mit Bluetooth ausgestattetBatterieparameter bequem am Smartphone oder Tablet überprüfenAnschluss an GX-Gerät möglichZusatzeingang für weitere Überwachungsmöglichkeitenunkomplizierte Installation Unterschiede zum BMV-712 Batteriemonitor Kein programmierbarer optischer und akustischer AlarmKein programmierbares Relais Warum ist Batterieüberwachung wichtig? Batterien werden in vielseitigen Bereichen eingesetzt, in den meisten Fällen, um Energie für eine spätere Nutzung zu speichern. Die Batterie selbst zeigt die gespeicherte Energiemenge aber nicht an. Die Lebensdauer von Batterien hängt von vielen Faktoren ab. Durch Unter- oder Überladung, Tiefentladung, zu hohe Lade- oder Entladeströme und hohe Umgebungstemperatur kann sich die Betriebsdauer verkürzen. Durch die Überwachung mit einem Batteriewächter erhält der Nutzer wichtige Rückmeldungen um bei Bedarf Gegenmaßnahmen zur Verlängerung der Batterielaufzeit zu treffen. Lieferumfang: 1x SmartShunt 2x Kabel mit Sicherung, für '+'-Verbindung und Starterbatterie oder Mittelpunktsverbindung