The Victron Battery-Protect BP-100 (MPN BPR000100400) disconnects the battery from the less important consumers before it is completely discharged (which would damage it) or before it no longer has sufficient energy to start the engine etc.. In addition, the BP series has overvoltage protection, which switches off the load at 16V or 32V battery voltage and protects it from damage. The BP supports AGM, lead-acid, gel and lithium batteries. 6 different switch-off thresholds can be setThe Battery Protect is very flexible and can be set to different cut-off voltages. The following cut-off thresholds can be activated on the device: 10.5V / 21V, 10V / 20V, 9.5V / 19V, 11.25V / 22.5V, 11.5V / 23V, 11.8V 23.6V In addition, there are different switch-on thresholds that can be selected for most switch-off thresholds. This makes this device the perfect protective device for your battery and thus ensures maximum service life, as most voltage converters or charge regulators have undervoltage protection, but this only intervenes at fairly low values, which are usually in the range of 10.5V / 21V. The higher this switch-off threshold is, the longer you will be able to enjoy your batteries, which are generally quite cost-intensive. Selecting the cut-off threshold Depending on the battery type, different minimum battery voltages apply which must be adhered to in order not to damage the battery. For AGM/gel batteries, we recommend setting the Batteryprotect to 11.5V switch-off threshold. For lithium batteries (LifePo4), 12.0V cut-off threshold is recommended. Depending on the intended use of the battery, it may be necessary to change these limits. The manufacturers also provide different specifications for their batteries. Therefore, always ask the battery manufacturer which cut-off threshold is the right one for your battery! Essential product features summarized For 12V and 24V batteries with automatic detection of the voltage range of the battery bank 6 different cut-off voltages selectable 100A maximum continuous current Simple programming and status display of settings via seven-segment display Extra mode for lithium batteries - in this mode, the BP can be controlled by the VE.Bus BMS Very low power consumption Explosion protection through integrated MOSFET switches that replace the relays and thus reduce the risk of sparking to zero Integrated alarm output Output for delayed alarm The alarm output is activated when the battery voltage falls below the preset value for shutdown for more than 12 seconds. Switching on the motor therefore does not activate the alarm. The alarm output is a short-circuit protected open collector output connected to the negative (minus) rail. Max. Current 50 mA. The alarm output is normally used to activate an audible signal, an LED or a relay. Load disconnection and reconnection delay The load is switched off 90 seconds after the alarm is activated. If the battery voltage rises again to the threshold value for reconnection within this period (after the engine has been started, for example), the load is not switched off. 30 seconds after the battery voltage has exceeded the specified voltage value for reconnection, the load is reconnected. Scope of delivery:1x Victron BPR000100400 BP-100 battery protection 100A 12V 24V1x instruction manual

The Victron Battery-Protect BP-48-100 (MPN BPR048100400) disconnects the battery from the less important loads before it is completely discharged (which would damage it) or before it no longer has sufficient energy to start the engine etc.. In addition, the BP series has overvoltage protection, which switches off the load in the event of overvoltage and protects it from damage. The BP supports AGM, lead-acid, gel and lithium batteries. An inverter must never be connected to the Victron Battery-Protect BP-48-100! 6 different switch-off thresholds can be set The Battery-Protect is very flexible and can be set to different cut-off voltages. The exact values can be found in the operating instructions for this product. There are also different switch-on thresholds that can be selected for most switch-off thresholds. This makes this device the perfect protective device for your battery and thus ensures maximum service life, as most voltage converters or charge regulators have undervoltage protection, but this only intervenes at fairly low values, which are usually in the range of 10.5V / 21V. The higher this switch-off threshold is, the longer you will be able to enjoy your batteries, which are generally quite cost-intensive. Selecting the cut-off threshold Depending on the battery type, different minimum battery voltages apply which must be adhered to in order not to damage the battery. For AGM/gel batteries, we recommend setting the Batteryprotect to 11.5V switch-off threshold. For lithium batteries (LifePo4), 12.0V cut-off threshold is recommended. Depending on the intended use of the battery, it may be necessary to change these limits. The manufacturers also provide different specifications for their batteries. Therefore, always ask the battery manufacturer which cut-off threshold is the right one for your battery! Essential product features summarized For 48V battery banks6 different cut-off voltages selectable100A maximum continuous currentSimple programming and status display of the settings via seven-segment displayExtra mode for lithium batteries - in this mode the BP can be controlled by the VE.Bus BMSVery low power consumptionExplosion protection through integrated MOSFET switches that replace the relays and thus reduce the risk of sparking to zeroIntegrated alarm output Output for delayed alarmThe alarm output is activated when the battery voltage falls below the preset value for shutdown for more than 12 seconds. Switching on the motor therefore does not activate the alarm. The alarm output is a short-circuit protected open collector output connected to the negative (minus) rail. Max. Current 50 mA. The alarm output is normally used to activate an audible signal, an LED or a relay.Load disconnection and reconnection delayThe load is switched off 90 seconds after the alarm is activated. If the battery voltage rises again to the threshold value for reconnection within this period (after the engine has been started, for example), the load is not switched off. 30 seconds after the battery voltage has exceeded the specified voltage value for reconnection, the load is reconnected. Scope of delivery:1x Victron BPR048100400 BP-48-100 Battery protection 100A 48V1x instruction manual

The Smart BatteryProtect 12V/24V-100A from Victron Energy (MPN BPR110022000) offers solid battery protection for 12V and 24V batteries of various types. Compared to the previous series, the Smart version has an integrated Bluetooth module that connects the Smart BatteryProtect (BP-100) to a smartphone or tablet. This allows you to program all the required switch-on/switch-off thresholds or set the appropriate value from 9 predefined thresholds.The BatteryProtect 12/24V can also be used as a charge interrupter between the battery charger and a lithium battery. A wide operating voltage range of 6-35 V makes the device universally applicable. The option of connecting an external switch or alarm to the BatteryProtect makes the BP-100 Smart the perfect battery monitor.Features of the Smart BatteryProtect 12/24V-100A100A maximum switching capacityFor 12V and 24V batteries with automatic detection of the voltage range of the battery bankExplosion protection thanks to integrated MOSFET switches, which replace the relays and thus reduce the risk of sparking to zeroIntegrated Bluetooth module, can be switched off as requiredFreely programmable switch-on and switch-off thresholds, easily and wirelessly via the VictronConnect appalternative programming and status display of settings possible via seven-segment displayintegrated alarm output, 9 predefined threshold values selectablean external alarm, an LED or a relay can be connected to the alarm outputthe load shedding of the BP can be controlled via a relay by external events that cannot be programmed in this wayOutput for delayed alarmThe alarm output is activated if the battery voltage falls below the preset value for switch-off for more than 12 seconds. Switching on the motor therefore does not activate the alarm. The alarm output is a short-circuit protected open collector output connected to the negative (minus) rail. Max. Current 50 mA. The alarm output is normally used to activate an audible signal, an LED or a relay.Solid battery protection for every battery typeThanks to its wide range of configuration options, the Smart BP-100 is the perfect protective device for your battery and thus ensures maximum service life, because although most voltage converters or charge controllers have undervoltage protection, this only intervenes at fairly low values, which are usually in the range of 10.5V / 21V. The higher this switch-off threshold is, the longer you will be able to enjoy your batteries, which are generally quite cost-intensive.Selecting the cut-off thresholdDepending on the battery type, different minimum battery voltages apply which must be adhered to in order not to damage the battery. For AGM/gel batteries, we recommend setting the Batteryprotect to 11.5V switch-off threshold. For lithium batteries (LifePo4), 12.0V cut-off threshold is recommended. Depending on the intended use of the battery, it may be necessary to change these limits. The manufacturers also provide different specifications for their batteries. Therefore, always ask the battery manufacturer which cut-off threshold is the right one for your battery!Scope of delivery:1x Victron Energy BPR110022000 Smart BatteryProtect 12/24V 100A1x operating instructions

The Smart BatteryProtect 12/24V-65A from Victron Energy (MPN BPR065022000) offers solid battery protection for 12V and 24V batteries of various types. Compared to the previous series, the Smart version has an integrated Bluetooth module that connects the Smart BatteryProtect (BP-65) to a smartphone or tablet. This allows you to program all the required switch-on/switch-off thresholds or set the appropriate value from 9 predefined thresholds.The BatteryProtect 12/24V can also be used as a charge interrupter between the battery charger and a lithium battery. A wide operating voltage range of 6-35 V makes the device universally applicable. The option of connecting an external switch or alarm to the BatteryProtect makes the BP-65 Smart the perfect battery monitor.Features of the Smart BatteryProtect 12V/24V-65A65A maximum switching capacityFor 12V and 24V batteries with automatic detection of the voltage range of the battery bankExplosion protection thanks to integrated MOSFET switches, which replace the relays and thus reduce the risk of sparking to zeroIntegrated Bluetooth module, can be switched off as requiredFreely programmable switch-on and switch-off thresholds, easily and wirelessly via the VictronConnect appalternative programming and status display of settings possible via seven-segment displayintegrated alarm output, 9 predefined threshold values selectablean external alarm, an LED or a relay can be connected to the alarm outputthe load shedding of the BP can be controlled via a relay by external events that cannot be programmed in this wayOutput for delayed alarmThe alarm output is activated if the battery voltage falls below the preset value for switch-off for more than 12 seconds. Switching on the motor therefore does not activate the alarm. The alarm output is a short-circuit protected open collector output connected to the negative (minus) rail. Max. Current 50 mA. The alarm output is normally used to activate an audible signal, an LED or a relay.Solid battery protection for every battery typeThanks to its wide range of configuration options, the Smart BP-65 is the perfect protective device for your battery and thus ensures maximum service life, because although most voltage converters or charge regulators have undervoltage protection, this only intervenes at fairly low values, which are usually in the range of 10.5V / 21V. The higher this switch-off threshold is, the longer you will be able to enjoy your batteries, which are generally quite cost-intensive.Selecting the cut-off thresholdDepending on the battery type, different minimum battery voltages apply which must be adhered to in order not to damage the battery. For AGM/gel batteries, we recommend setting the Batteryprotect to 11.5V switch-off threshold. For lithium batteries (LifePo4), 12.0V cut-off threshold is recommended. Depending on the intended use of the battery, it may be necessary to change these limits. The manufacturers also provide different specifications for their batteries. Therefore, always ask the battery manufacturer which cut-off threshold is the right one for your battery!Scope of delivery:1x Victron Energy BPR065022000 Smart BatteryProtect 12/24V 65A1x operating instructions

The Victron Battery-Protect BP-220 (MPN BPR122022000) disconnects the battery from the less important loads before it is completely discharged (which would damage it) or before it no longer has sufficient energy to start the engine etc.. In addition, the BP series has overvoltage protection, which switches off the load at 16V or 32V battery voltage and protects it from damage. The BP supports AGM, lead-acid, gel and lithium batteries.6 different switch-off thresholds can be setThe Battery Protect is very flexible and can be set to different cut-off voltages. The following cut-off thresholds can be activated on the device: 10.5V / 21V, 10V / 20V, 9.5V / 19V, 11.25V / 22.5V, 11.5V / 23V, 11.8V 23.6VIn addition, there are different switch-on thresholds that can be selected for most switch-off thresholds. This makes this device the perfect protective device for your battery and thus ensures maximum service life, as most voltage converters or charge regulators have undervoltage protection, but this only intervenes at fairly low values, which are usually in the range of 10.5V / 21V. The higher this switch-off threshold is, the longer you will be able to enjoy your batteries, which are generally quite cost-intensive.Selecting the cut-off thresholdDepending on the battery type, different minimum battery voltages apply which must be adhered to in order not to damage the battery. For AGM/gel batteries, we recommend setting the Batteryprotect to 11.5V switch-off threshold. For lithium batteries (LifePo4), 12.0V cut-off threshold is recommended. Depending on the intended use of the battery, it may be necessary to change these limits. The manufacturers also provide different specifications for their batteries. Therefore, always ask the battery manufacturer which cut-off threshold is the right one for your battery!Essential product features summarizedFor 12V and 24V batteries with automatic detection of the voltage range of the battery bank6 different cut-off voltages selectable220A maximum continuous currentSimple programming and status display of settings via seven-segment displayExtra mode for lithium batteries - in this mode, the BP can be controlled by the VE.Bus BMSVery low power consumptionExplosion protection through integrated MOSFET switches that replace the relays and thus reduce the risk of sparking to zeroIntegrated alarm outputOutput for delayed alarmThe alarm output is activated when the battery voltage falls below the preset value for shutdown for more than 12 seconds. Switching on the motor therefore does not activate the alarm. The alarm output is a short-circuit protected open collector output connected to the negative (minus) rail. Max. Current 50 mA. The alarm output is normally used to activate an audible signal, an LED or a relay.Load disconnection and reconnection delayThe load is switched off 90 seconds after the alarm is activated. If the battery voltage rises again to the threshold value for connection within this period (after the motor has been started, for example), the load is not switched off. The load is reconnected 30 seconds after the battery voltage has exceeded the specified voltage value for reconnection.Scope of delivery:1x Victron BPR122022000 BP-220 Battery protection 220A 12V 24V1x operating instructions