Optima RT F 4.2 RedTop 50Ah car battery
€194.50*
excl. €7.50 deposit
Product number: ORTF42-10137
Often bought together
1x
1x
1x
The Most Important
| Battery technology:: | |
|---|---|
| Capacity (Ah): | 50 Ah |
| Dimensions (L x W x H): | |
| Tension: | 12V |
| : |
Product information "Optima RT F 4.2 RedTop 50Ah car battery"
Optima RT F 4,2 RedTop 50Ah car battery
The Optima RT F 4.2 RedTop 50Ah car battery is ready for use for a long time and is always at your service. In the initial starting phase, RedTop batteries with the patented Spiralcell technology deliver immense power. Thanks to the extremely low self-discharge of the Optima RT F 4.2 RedTop 50Ah car battery, you can store it for a very long time without the battery losing its starting ability. This in turn can increase your productivity, as maintenance intervals are extended and repair costs for the engine are reduced.
But the Optima RT F 4.2 RedTop 50Ah car battery offers more than just the power to start an engine. It lasts up to three times longer and has up to 15 times better vibration resistance than other batteries. This Optima RedTop AGM car battery is also completely leak-proof. Thanks to Spiralcell technology, this battery offers the lowest internal resistance of any lead-acid battery on the market. It is also characterized by its fast charging capacity, so that full power is available again after just a few driving cycles. Basically, this car battery is tough as nails. Its performance and longevity are capabilities you can fully trust.
Advantages:
- More power in the first 10 seconds of starting than comparable conventional lead-acid batteries
- Consistent power quality - ensures the power of your battery throughout the discharge process
- 15 times higher vibration resistance than other batteries
Leak-proof, flexible and can be installed in almost any position
Lasts up to three times longer than other batteries
| Battery technology:: | AGM (VRLA) |
|---|---|
| Capacity (Ah): | 50 Ah |
| Dimensions (L x W x H): | 260 x 185 x 184 mm |
| Execution: | Ready for immediate use (filled & charged) |
| Tension: | 12V |
| Kälteprüfstrom: | 815 A |
| Start-Stop-Betrieb: | Ja |
| Schaltung: | 7 (Pole vorne, Pluspol links) |
| Endpolart: | 21 (Frontanschluss, 3/8" Innengewinde, US-Anschluss) |
| Besonderheiten: | Kann liegend verbaut werden |
| Wartungsfrei nach EN: | Ja |
| Zentrale Gasableitung: | Nicht erforderlich |
| Zustand: | Neu (Original - Direkt vom Hersteller) |
| Modell-Reihe: | RedTop |
Downloads "Optima RT F 4.2 RedTop 50Ah car battery"
Login
Skip product gallery 
Autobatterien Ladegeräte
Bosch C10 Battery Charger 3.5A 12V
Bosch C10 Battery Charger – Powerful, Safe & Reliable (3.5 A) 12V The Bosch C10 battery charger stands for intelligent charging technology, the highest safety and proven Bosch quality. With a charging power of 3.5 amps It charges vehicle batteries efficiently and gently – ideal for daily use as well as for longer downtimes. Thanks to the automatic, microprocessor-controlled charging process The C30 automatically detects the battery status and adjusts the charging parameters optimally. This extends the life of the battery and reliably prevents overcharging. The compact, robust design makes the charger special user-friendly – simply connect, turn on and the rest runs automatically. Perfectly suited for Car, motorcycle and other 12 V batteries. Your advantages at a glance: 3.5 A charging power – fast & battery-friendlyIntelligent automatic charging with conservation functionHigh security by overcharge and short circuit protectionBosch brand quality – durable & reliableCompact & lightweight – ideal for garage, workshop or on the goBattery technologies - Lead acid, AGM and gel Conclusion:The Bosch C10 is the perfect solution for those who need their battery safe, efficient and effortless want to load. A reliable helper you can rely on at any time.
€42.88*
Bosch C70 Battery Charger 10A 12V&24V
The Bosch C70 battery charger stands for reliable performance, intelligent technology and maximum versatility. With a powerful Charging current of 10 amps It's ideal for workshops, fleets, and demanding home users. Whether maintenance, fast charging, or battery replacement – this charger delivers consistent, professional-level performance. Fast, efficient & thought out Thanks to the thanks and thanks of the experts, we are able to provide you with the support you need Support loading operation The Bosch C70 supplies the vehicle with power directly – perfect when changing batteries or during longer diagnostic work. The integrated microprocessor ensures optimized charging cycles and significantly reduces charging time. Even in the event of a power outage, everything remains relaxed: the last setting is saved and charging continues automatically. Maximum compatibility The charger is suitable for almost all common vehicle types. It loads 12V and 24V batteries from 2 Ah to 300 Ah – regardless of whether Car, truck, motorcycle, vintage car, van or motorhome. Support is provided Lead-acid, AGM, EFB, GEL and SLI batteries. Protects & extends battery life As soon as the battery is fully charged, the Bosch C70 automatically switches to the Trickle loading mode – for permanently full capacity without overloading. In addition, the Regeneration function with pulse charge for revitalizing weakened batteries and extending their lifespan sustainably. Your advantages at a glance: 10A charging current for fast and efficient charging12V & 24V – suitable for almost all vehicle typesIntelligent microprocessor control with memory functionAutomatic maintenance and regeneration chargeIdeal for maintenance, diagnostics and battery replacement Bosch C70 – when your battery deserves maximum performance.A charger you can rely on at any time.
€79.16*
CTEK MXS 5.0 5A/12V battery charger
Test winner of the charger comparison test of Autobild (issue 43/2010). Ctek battery charger suitable for all types of 12V lead-acid batteries (wet, maintenance-free, AGM, calcium/calcium and gel batteries) The MXS 5.0 is a charger equipped with the latest technology, which was previously reserved for CTEK professional devices. The charger solves a range of battery problems; it is the perfect charger for users with the highest demands. The MXS 5.0 offers a range of features, such as battery diagnostics that indicate whether the battery can accept and hold a charge, a special reconditioning function that recovers deeply discharged batteries with acid stratification, a unique maintenance charging function, a mode for optimized charging on cold winter days and the ability to charge demanding AGM batteries (i.e. Optima). The unique display allows the user to follow the entire charging process. The MXS 5.0 is a fully automatic 8-stage charger with a selectable charging current between 0.8 A and 5 A for 12V batteries from 1.2 - 110Ah and for maintenance charging up to 160Ah. The charger has protection class IP65 (protected against dust and splash water), was built to protect vehicle electronics systems, is protected against sparks, reverse polarity and short circuits. Details: Desulphation Perfect charge and charge retention Unique regeneration of deeply discharged batteries CTEK's 8-stage now visible via LED display Electronics safe Splashproof and dustproof (IP 65) Pulse charge retention GS tested
€77.98*
CTEK MXS 5.0 Test & Charge battery charger
Tests the voltage, starting power and performance of the alternator The MXS 5.0 TEST & CHARGE is designed for batteries between 1.2 Ah and 110 Ah. The test function includes three easy-to-use programs for testing battery voltage, starting power and alternator performance, providing a complete picture of the battery state of charge and system health of the vehicle charging system. In addition, the MXS 5.0 TEST & CHARGE features a patented automatic desulphation program and CTEK's patented Float/Pulse system. This is the most efficient trickle charge mode when a battery is left connected to the charger for an extended period of time. Functions Charging of batteries between 1.2 Ah and 110 Ah Patented float/pulse trickle charge Easy to read LED display splash-proof and dust-proof (IP65) non-sparking reverse polarity protected short-circuit proof
€99.04*
Noqon NPC4 battery charger 4A 6V/12V
Noqon NPC4 6V/12V battery charger with 4A charging current The car battery charger is an 11-step car battery charger suitable for charging and trickle charging 6V or 12V lead-acid batteries (batteries) with liquid electrolyte (WET), maintenance-free lead-acid batteries (MF), gel electrolyte (GEL) or electrolyte-absorbing mats (AGM). Select the desired charging voltage (6V or 12V) and the microprocessor-controlled charger takes care of everything fully automatically until the charging cycle is complete and the batteries are fully charged. The German-language display is easy to understand and convenient to operate. Thanks to the test function, battery charge levels can be determined before charging and the integrated memory function continues the charging process even after power interruptions without having to start from the beginning. There aresix charging programs to choose from. Fully automatic battery charging takes place in 11 charging steps. Modern safety technology with reverse polarity protection, overheating protection, overload protection and short-circuit protection protects you and the device from incorrect operation. Two cables with quick connectors and comfort plugs (permanent charging cable with eyelets for fixed installation & charging cable with clamps) are included with the jet-proof and dust-proof device (protection class IP65). Features: Suitable for continuous charging Test function/battery tester Memory function 6 charging programs 11 charging steps Technical data: Specification: at 12 V: 3.8 A / 0.8 A, 6 V: 0.8 A, microprocessor-controlled Power supply: 230V, 50 Hz220V - 240V, 50Hz Charging voltage: 7.2V/7.4V ±0.25 VDC - 14.4V/14.7V ±0.25 VDC Rated output current: 6V: 0.8A ±10% / 12V: 0.8A / 3.8A ±10% Current consumption: Max. 0.9 A / 230 V Charger type: 11 charging steps, automatic charging cycle Ambient temperature: -10 to +40 °C Reverse current: 0.2 mA after completion of charging (if charger remains connected to 230 V) 50 mA if charger disconnected from 230 V. Battery type: 6V & 12V lead-acid batteries (Wet, MF, GEL, EFB, AGM) Recommended battery capacity: 6V: 1.2 - 14Ah / 12V: 1.2 - 120Ah Protection class: IP65, protected against water jets Protection: Reverse polarity, thermal and overload protection, time control Scope of delivery: 1 x Noqon NPC4 battery charger 1 x crocodile clips 1 x quick contact cable with ring terminals
€20.40*
Noqon NPC8 battery charger 8A 12V/24V
Noqon NPC8 battery charger 12V/24V with 8A charging current The car battery charger is an 11-step car battery charger suitable for charging and trickle charging 12V or 24V lead-acid batteries (batteries) with liquid electrolyte (WET), maintenance-free lead-acid batteries (MF), gel electrolyte (GEL) or electrolyte-absorbing mats (AGM). Select the desired charging voltage (12V or 24V) and the microprocessor-controlled charger takes care of everything fully automatically until the charging cycle is complete and the batteries are fully charged. The German-language display is easy to understand and convenient to operate. Thanks to the test function, battery charge levels can be determined before charging and the integrated memory function continues the charging process even after power interruptions without having to start from the beginning. There aresix charging programs to choose from. Fully automatic battery charging takes place in 11 charging steps. Modern safety technology with reverse polarity protection, overheating protection, overload protection and short-circuit protection protects you and the device from incorrect operation. Two cables with quick connectors and comfort plugs (permanent charging cable with eyelets for fixed installation & charging cable with clamps) are included with the jet-proof and dust-proof device (protection class IP65). Features: Suitable for continuous charging Test function/battery tester Memory function 6 charging programs 11 charging steps Technical data: Specification: at 12 V: 3.8 A / 0.8 A, 6 V: 0.8 A, microprocessor-controlled Power supply: 220V - 240V, 50Hz Charging voltage: 14.4V/14.7V ±0.25 VDC, 28.8V/29.4V ±0.25 VDC Rated output current: 12V: 2A / 8A ±10% - 24V: 4A ±10% Current consumption: Max. 0.9 A / 230 V Charger type: 11 charging steps, automatic charging cycle Ambient temperature: -10 to +40 °C Battery type: 12V & 24V lead-acid batteries (Wet, MF, GEL, EFB, AGM) Recommended battery capacity: 12V: 2.2 - 180Ah / 24V: 14 - 120Ah Protection class: IP65, protected against water jets Protection: Reverse polarity, thermal and overload protection, time control Scope of delivery: 1 x Noqon NPC8 battery charger 1 x crocodile clips 1 x quick contact cable with ring terminals
€35.70*
PACO MEC1220L 20A/12V Wet, AGM, Gel, LIFePO4 Battery Charger
PACO MEC1220 20A/12V battery charger
€89.00*
VARTA automatic charger VPZ-LOAD 1000 PLUS 6V/12V / 1A
VARTA Powerzone VPZ-LOAD 1000 Plus The Varta Powerzone VPZ-LOAD 1000 Plus charger takes away all your worries about your car battery. Whether you have an AGM, GEL, lead-acid, VRLA or wet battery, this charger will charge it for you. It has an advanced and intelligent microprocessor that controls the charging process. In addition, automatic diagnostic, rescue, charging, maintenance and charge retention functions are fully covered by the VPZ-LOAD 1000 Plus. Removing or disconnecting the car battery is no longer necessary with this device. Set the required battery voltage manually and connect the charger to the battery. Provided everything has been set correctly, the Varta VPZ-LOAD 1000 Plus charger will carry out the necessary measures for proper and gentle charging. You can also leave the charger permanently connected to the battery (when stationary) using the charge retention function. If the charger detects a defect or an incorrect setting, an error (display: "ER-X") is displayed. Safety functions To guarantee complete safety during charging, the charger is equipped with extensive safety functions. These safety functions provide protection for/against: Reverse polarity short circuits overheating Overcharge protection overvoltage Charging with defective batteries (automatic charge termination) Sparking Charging stages The charger has a 7-stage charging control, which is controlled and regulated by a microprocessor. This means that the charging stages are set automatically depending on the battery condition. Stage 1 - DiagnosisStage 2 - Pre-chargingStage 3 - SoftStartStage 4 - Main charging phaseStage 5 - Saturation chargingStage 6 - Rest/overgrowth phaseStage 7 - Continuous charge maintenance Technical data Charging voltage: 6V / 12VMax. charging current: 1ASupported batteries: AGM, GEL, lead-acid, lead-calcium, VRLA, ML, SLArecommended capacity: 2Ah-110AhLength: 125mmWidth: 78mmheight: 40mmWeight: 0.8kg Scope of delivery 1x Varta Powerzone VPZ LOAD 1000 Plus charger1x pole terminal adapter 0.6m1x ring lug adapter 0.6m1x cigarette lighter adapter 0.6m1x extension 3m1x storage bag1x detailed operating instructions
€59.90*
VARTA automatic charger VPZ-LOAD 5000 PLUS 6V/12V / 5A
VARTA Powerzone VPZ-LOAD 5000 Plus The Varta Powerzone VPZ-LOAD 5000 Plus charger takes away all your worries about your car battery. Whether you have an AGM, GEL, lead-acid, VRLA or wet battery, this charger will charge it for you. It has an advanced and intelligent microprocessor that controls the charging process. In addition, automatic diagnostic, rescue, charging, maintenance and charge retention functions are fully covered by the VPZ-LOAD 5000 Plus. Removing or disconnecting the car battery is no longer necessary with this device. Set the required battery voltage manually and connect the charger to the battery. If everything has been set correctly, the Varta VPZ-LOAD 5000 Plus charger will carry out the necessary measures for proper and gentle charging. You can also leave the charger permanently connected to the battery (when stationary) using the charge retention function. If the charger detects a defect or an incorrect setting, an error (display: "ER-X") is displayed. Safety functions To guarantee complete safety during charging, the charger is equipped with extensive safety functions. These safety functions provide protection for/against: Reverse polarity short circuits overheating Overcharge protection overvoltage Charging with defective batteries (automatic charge termination) Sparking Charging stages The charger has a 7-stage charging control, which is controlled and regulated by a microprocessor. This means that the charging stages are set automatically depending on the battery condition. Stage 1 - DiagnosisStage 2 - Pre-chargingStage 3 - SoftStartStage 4 - Main charging phaseStage 5 - Saturation chargingStage 6 - Rest/overgrowth phaseStage 7 - Continuous charge maintenance Technical data Charging voltage: 6V / 12V Max. charging current: 5ASupported batteries: AGM, GEL, lead-acid, lead-calcium, VRLA, ML, SLArecommended capacity: 2Ah-110AhLength: 150mmWidth: 80mmheight: 45mmWeight: 0.8kg Scope of delivery 1x charger Varta Powerzone VPZ LOAD 5000 Plus1x pole terminal adapter 0.6m1x ring terminal adapter 0.6m1x cigarette lighter adapter 0.6m1x extension 3m1x detailed operating instructions
€79.90*
Skip product gallery
Autobatterien Zubehör
Battery Monitor BM6 Battery monitoring with free app 12V
Main functions:1. real-time display battery current, temperature and voltage.2. automatically test the vehicle's starting and charging systems.3. send alarm notification when the battery is abnormal.4. 4 devices support multi-device connection and can be monitored on the same page.5. record the lane, cost and driving habits of each trip and can be exported to the Excel file.6. automatically note the parking position and provide the CAR FINDER function via navigation.7. store historical data up to 30 days ( voltage, charge percentage and temperature ) in the device. 8. store unlimited historical data in the app. Basic functions:1.Notify users when the charge is low.2.check the charging history in graph mode.3.display the battery charge level in real time.4.Near-full perception to be notified automatically.Support cell phones: All iOS and Android smartphones with Bluetooth 4.0iOS ( iPhone 4S, 5, 5C, 5S and above; iPad 2, iPad Air, iPad mini, iPad mini 2 and above )Android: At least Android 4.3 ( support for Bluetooth 4.0 phones )Vehicle coverageAll 12V batteries, including motorcycle, car, SUVs, MPVs, light trucks, trucks and boats.Including lead-acid, AGM, GEL and EPB batteries.Package included:1 piece x BM6 battery monitorWeight: 30g Technical data:1. product name: battery monitor2. bluetooth version: 4.23. bluetooth name: BM64. input voltage: DC 6V ~ 20V5. voltage accuracy ( 9V ~ 16V ): ± 0,03 V.6. average working current: 1.5 mA7. working temperature: -40 ° C ~ 90 ° C ( -40 ° F ~ 194 ° F )8. reverse connection protection: built-in9. short circuit protection: Built-in10. waterproof: IP6711. physical dimensions: ( L ) 55 mm x ( W ) 41 mm x ( H ) 12.5 mm
€17.67*
BATTERY TERMINAL GREASE
Plastic-compatible special grease based on lime soap. Protects battery terminals and electrical contacts from corrosion and oxidation. For safe starting, bright lighting and longer battery life. Prevents acid damage, is compatible with plastics and prevents leakage currents. Prevents the contact resistance from increasing during operation and ensures a lower loss than with untreated contacts. Labeled according to DIN 51502 K2G-30. Temperature range: -30 °C to +100 °C.
€4.00*
Bluetooth battery tester for car, motorcycle and truck KONNWEI BK200 6V/12V/24V
Bluetooth battery tester for car, motorcycle and truck KONNWEI BK200 6V/12V/24V KONNWEI BK200 battery tester is the latest battery system analyzer tool for cars, trucks and motorcycles with the function of testing 6V, 12V to 24V batteries. It can quickly and accurately find out the battery status, including state of charge, life percentage, internal resistance and so on. Besides, it can help you check the status of the vehicle when starting, detect malfunction of the battery system, etc. KONNWEI BK200 is a professional automotive diagnostic tool for all kinds of battery problems. It provides professional battery diagram voltage monitoring and upload function for in-depth analysis. It covers the most common battery types, including normal flooded batteries, AGM flat batteries, AGM spiral batteries, GEL batteries, EFB batteries, etc. The BK200 is a perfect and reliable battery system tool for all DIY enthusiasts and professionals. Different from the traditional test method. KONNWEI BK200 uses the latest Bluetooth technology to detect the car battery. You no longer need to stand in front of the car and wait for the test, after connecting the car battery, you can open the app on your phone/tablet for car battery testing, which is customer-friendly and easy to use.With the KONNWEI BK200 car battery tester, we can check the overall condition of the battery, including the cranking test, and perform a complete system charge test. The starter test is to test and analyze the starter to check if the starter is working properly, and the charging test is to check the condition of the charging system to avoid damaging the battery. It is much more convenient than driving a few kilometers to a nearby garage. Our Bluetooth car battery tester is compatible with all 6-volt and 12-volt lead-acid batteries, including normal flooded batteries, AGM flat plate batteries, AGM spiral batteries, GEL batteries and EFB-LITHIUM batteries with a test range of 100-2000 CCA. Compatible with cars, motorcycles, trucks, RVs, ATVs, SUVs, boats, yachts, lawnmowers and even golf carts. The KONNWEI BK200 is plug-and-play and provides accurate test reports within seconds, significantly improving test speed compared to other battery testers. It also has a reverse polarity protection function. Reverse polarity will not damage the tester and has no negative impact on the car and battery. KONNWEI BK200 can directly test the power loss of the battery without the need to fully charge and test it first. Support for multiple languages such as English, Spanish, German, Russian, Italian, French, Portuguese, etc. The actual language depends on the system language setting of your phone/tablet. The language display will follow the change of your system language.
€39.00*
Elbow with hose for central gas discharge (cut to size)
Elbow with hose for central gas discharge (cut to size) Connection diameter = 6 mm Hose diameter = approx. 8 mm Hose inner diameter = approx. 5 mm Hose length = approx. 500 mm
€1.90*
VOLTIMA JUMP STARTER VJS500 Battery-less jump starter
VOLTIMA JUMP STARTER 500A Maintenance-free, battery-free and cold-resistant to safely recharge an almost empty vehicle battery in less than 2 minutes. DescriptionSmooth ABS housing with beautiful design. This ultracapacitor jump starter can recharge a nearly dead battery in less than 2 minutes because it contains ultracapacitors instead of lithium battery which is more versatile, this greatly reduces the risk of fire or exploration hazards. Not only that, this device is tested to be able to jump start over 10,000 times and has an average lifespan of over 10 years with normal use and care. Outstanding performance even in a harsh environment down to -40C °. _______________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ 3 EASY STEPS TO JUMP START YOUR CAR! Connect to the car battery Press the on/off switch and wait 1-2 minutes Ready to start your car _______________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ Features Maintenance free Super safe, full protection 2 min. instant charge LCD display Easy to use and carry Compact size 10,000 cycles (lifetime) ________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ applications Starting current: 500A Peak current: 1000A Charging voltage: 12V Operating temperature: -40C° to 65°C( -40°F to 149°F) Dimensions: (mm): 200 x 57 x 136mm Weight: 1.15Kg ______________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
€113.05*