Diese interessante Gerätekombination bestehend aus 3-fach Thermometer und genauer Quartzuhr und wird aus dem Fahrzeug-Bordnetz betrieben. Hervorzuheben ist der geringe Stromverbrauch der Einheit sowie die große LCD-Anzeige, die auch aus weiterer Entfernung sehr gut ablesbar ist. Bei ungünstigen Lichtverhältnissen sorgt die eingebaute weiße Hinterleuchtung des Displays für eine gute Ablesbarkeit. Der Thermometerteil misst die Raumtemperatur durch den im Gerät eingebauten Sensor. Zusätzlich ist die externe Fernmessung durch den mitgelieferten Außenfühler vorgesehen. Er wird im Außenbereich z. B. unter der vorderen Stoßstange des Fahrzeugs montiert und kann hier die Außentemperatur erfassen. Ein weiterer externer Messeingang 3 ist beispielsweise zur Überwachung der Medikamentenaufbewahrung, von Kühlboxen oder Wärmeboxen etc. hervorragend geeignet. Bei einer Messauflösung von 0,1°C betragen die Messbereiche aller Sensoren -30°C bis +70°C. Der Uhrenteil umfasst die Anzeige Minuten und Stunden im 24 Stunden Anzeigeformat und den blinkenden Doppelpunkt zur Funktionskontrolle. In der unteren Zeile kommt der Wochentag zur Anzeige. Die Uhr arbeitet mit hoher Genauigkeit und besitzt eine Gangreserve gegen Spannungsausfall. Bei DCF-Betrieb der Uhr (DCF-Modul erforderlich) informiert die Anzeige durch ein separates Segment Lieferumfang:  - 1 Stk. LCD-Thermometer  - 1 Stk. Ext. Temperatursensor  - 4 Stk. Befestigungsschrauben  - 1 Stk. Bohrschablone  - 1 Stk. Montage- bzw. Bedienungsanleitung

LCD-Voltmeter S: Dieses digitale Messgerät bringt wahlweise die Spannung der Bord- und der Starter-Batterie zur Anzeige. Die Spannungen werden als genauer Zahlenwert dargestellt.Die zusätzliche Balkenanzeige arbeitet im Bereich von 10,5 bis 15 Volt und stellt damit den interessantesten Bereich der Batteriespannung von der Tiefentladung bis zur maximalen Ladespannung anschaulich und auf einen Blick erfassbar dar. Bei der Installation des Gerätes wird für diese Funktion einmalig auf 12V- oder 24V-Betrieb eingestellt. Bei 24V-Betrieb entspricht der Bereich dann 21,0 bis 30,0 Volt. Ein Mischbetrieb von z.B. 24V Starterkreis und 12V-Versorgungskreis ist ebenfalls möglich, da diese Einstellung separat für die Starter- und Bord-Batterie geschieht. Der Anschluss erfolgt durch Schraubklemmen auf der Rückseite des Gerätes. Passend zum VOTRONIC Modulsystem reiht sich das LCD-Voltmeter S sowohl optisch als auch mechanisch (einheitliche Höhe 85 mm) an die übrigen Anzeigemodule an und die geringe Einbautiefe von nur 22 mm erlaubt die Montage an nahezu jeder Stelle. Die Anzeige ist bei Bedarf weiß hinterleuchtet (schaltbar) und auch aus größeren Entfernungen sowie bei allen Lichtverhältnissen sehr gut ablesbar.Lieferumfang:1 St. LCD Voltmeter S (Anzeige)4 St. Befestigungsschrauben1 St. Bedienungsanleitung1 St. Bohrschablone

Votronic remote control S suitable for automatic chargers of the Pb and VAC series. If the device is difficult to access, the control LEDs provide a remote display of the device status and charging progress. One of the respective main device functions can be remote-controlled with the switch, e.g. silent run (night mode) for chargers in the Pb and VAC series. The remote control is designed as a panel version and matches the other displays of the VOTRONIC module system both visually and mechanically (same height 85 mm). Product details Automatic loaders Pb series Automatic loaders VAC series Made in Germany Technical data Dimensions 85x47mm Installation dimensions 65x35 (max. depth 16 mm) Weight 23g Test mark CE, E-test (EMC/vehicle directive) Scope of delivery Connection cable 5m long, ready to plug in on both sides for device connection, fixing screws, drilling template

The Votronic waste water tank gauge S (MPN 5313) was designed for precise level measurement and can be used for all tank materials and tank sizes. The tank level is visualized via a 3-colour scale, which is displayed on 10 LEDs, each representing 10% of the tank content. The display works continuously, as intermediate levels are displayed with variable brightness and therefore trends can be recognized immediately.The waste water tank display Tank display S is designed as a panel version to match the VOTRONIC modular system and fits in perfectly with other VOTRONIC display units (uniform height 85 mm). Of course, it is also possible to retrofit a single display in the vehicle. Small front panel dimensions and the particularly low installation depth of just 18 mm allow installation in almost any location. The indicator is protected against reverse polarity and overload and is easy to connect via screw terminals on the back of the device.Key product features of the waste water tank indicator S, 5313 Suitable for 12V and 24V DC operating voltage Low current consumption: only 1 - 30 mA Test mark: E-test, (EMC/vehicle directive) Panel dimensions WxHxD: 47 x 85 x 20 mm Installation dimensions: 29 x 63 x 18 mm Can be switched on and off at the touch of a button High display resolution of the tank level thanks to 10-stage display Suitable for the Votronic module system Can also be operated with 2 tank sensors The display units can also be assigned to 2 tanks (e.g. indoor/outdoor tank, summer/winter operation, additional tank, etc.). Single switches 2xUM are suitable for switching, e.g. switch panel 16 A S art. no. 1289 or switch panel 2x16 A S art. no. 1291Compatible with many Votronic tank sensors Tank electrode 12-24 K, 5543 Tank electrode 15-50 K, 5545 Tank electrode 20 K-WC, 5555 Tank sensor FL, 5530 Tank sensor 30-110 K-FL, 5551 Scope of delivery:1x Votronic 5313 waste water tank display S1x set of fixing screws1x drilling template1x operating instructions

The Votronic waste tank indicator S (MPN 5315) was designed for precise level measurement and can be used for all tank materials and tank sizes. The tank level is visualized via a 3-colour scale, which is displayed on 10 LEDs, each representing 10% of the tank content. The display works continuously, as intermediate levels are displayed with variable brightness and therefore trends can be recognized immediately.The waste holding tank display Tank display S is designed as a panel version to match the VOTRONIC modular system and fits in perfectly with other VOTRONIC display units (uniform height 85 mm). Of course, it is also possible to retrofit a single display in the vehicle. Small front panel dimensions and the particularly low installation depth of just 18 mm allow installation in almost any location. The indicator is protected against reverse polarity and overload and is easy to connect via screw terminals on the back of the device.Key product features of the waste tank indicator S, 5315 Suitable for 12V and 24V DC operating voltage Low current consumption: only 1 - 30 mA Test mark: E-test, (EMC/vehicle directive) Panel dimensions WxHxD: 47 x 85 x 20 mm Installation dimensions: 29 x 63 x 18 mm Can be switched on and off at the touch of a button High display resolution of the tank level thanks to 10-stage display Suitable for the Votronic module system Can also be operated with 2 tank sensorsThe display units can also be assigned to 2 tanks (e.g. indoor/outdoor tank, summer/winter operation, additional tank, etc.). Single switches 2xUM are suitable for switching, e.g. switch panel 16 A S art. no. 1289 or switch panel 2x16 A S art. no. 1291Compatible with many Votronic tank sensors Tank electrode 12-24 K, 5543 Tank electrode 15-50 K, 5545 Tank electrode 20 K-WC, 5555 Tank sensor FL, 5530 Tank sensor 30-110 K-FL, 5551 Scope of delivery:1x Votronic 5315 holding tank display S1x set of fixing screws1x drilling template1x operating instructions

The Votronic tank electrode 20 K-WC (HAN 5555) is a tank sensor for cassette toilets in motorhomes, which are now considered the absolute standard. Cassette toilets are compact in design and have a display which, unfortunately, usually only marks the full state. Once this is reached, the toilet in the vehicle can no longer be used. The use of tank sensors in combination with Votronic fill level indicators allows you to plan the disposal and replacement of your mobile tanks in advance.The main product features of the 20 K-WC tank sensor Tank sensor specially designed for cassette toilets and mobile tanks Compact, robust, waterproof (IP67) Simple installation, no inspection opening required With 3-pin circular plug connection for disconnecting the tank Complete installation material included in the scope of delivery Rod electrode, easy to shorten to tank height Installation diameter 38 mm (or PG 29 thread) Flange diameter 46.5 mm Test mark: E-test (EMC/vehicle directive) Connection cable 75 cm long Mounting from above using mounting ring Detachable plug connection for tank emptying Optimal in combination with Votronic level indicators The tank sensor is compatible with the following Votronic displays: . Waste water indicator S, 5313 Holding tank indicator S, 5315 Info Panel Pro, 5330 Info Panel Pro 24V VPC Terra VPC Mercury VPC Jupiter 100 Smart Shunt, 5747 VPC Jupiter 200 Smart Shunt, 5748 VPC Jupiter 400 Smart Shunt, 5749 Solid measurement technology and simple installationThe tank electrode 20 K-WC has been further developed on the basis of the long-established tank electrode to provide a fully-fledged level indicator especially for use in cassette toilets. The compact design makes it possible to simply screw the tank sensor into the toilet cassette from above using the mounting ring supplied. The 38 mm diameter mounting hole required for this is easy to make using a hole saw. The fully encapsulated electronics are designed to be waterproof (IP67) and suitable for rough operation when flushing the toilet cassette.To change the cassette, the tank electrode 20 K-WC is disconnected from the vehicle via a solid 3-pin round plug and the plug is fixed to the cassette. In addition to the 3-pin round plug connection, the scope of delivery also includes a mounting ring and the complete mounting material.Scope of delivery:1x Votronic 5555 Tank electrode 20 K-WC

Effective battery charging and monitoring for motorhomes, caravans, boats and self-sufficient solar systems! How much charge does my on-board battery actually have left? Is the battery really full? Why is energy being drawn from the battery despite consumers being switched off?The VOTRONIC LCD battery computer S answers these questions to the exact percentage (%) and ampere hour (Ah). At the touch of a button, it provides comprehensive information on the current charge status of the battery, the battery currents flowing and the voltage level of the battery.The device is in constant contact with "its battery" and thus registers and evaluates all battery actions. All charging and discharging currents are meticulously counted, battery size, self-discharge, battery load etc. are taken into account using programmed characteristic curve fields. The remaining battery capacity is then calculated from the measured values and the battery size. The result is the correct display of the state of charge (remaining capacity, residual charge) of the on-board battery as a numerical value in ampere hours ("Ah") and in percent ("%") as well as a clear fill level bar, like a fuel gauge.The LCD battery computer S is suitable for all battery types (acid, gel, AGM, lithium adjustable) with 12V and 24 V battery voltage. Of course, the current battery voltage ("V") and the current battery current ("A") are also available in the display. Discharge currents (consumers) are indicated by a minus sign. Charging currents are also indicated by a clearly legible "Charge" symbol. Independently of this, there is a further display option for the voltage of a second battery, e.g. for monitoring the vehicle's starter battery.A plug-in connection cable connects the display completely to a robust precision measuring resistor (shunt), which is connected directly to the negative terminal of the on-board battery and at which the voltages and currents of the battery are recorded.The following values are measured: On-board battery voltage Battery voltage starter battery Battery current (charging ="+"; discharging ="-") Load from consumers Battery capacity "Ah" (remaining charge in ampere hours) Battery capacity "%" (remaining charge in percent) Switching output (freely programmable) Flashing warning display in the event of undervoltage or overvoltage Can I also program the battery computer? The LCD battery computer S has a freely programmable switching output for control, monitoring and warning purposes, e.g. to automatically switch loads or issue a warning depending on the charge status of the on-board battery (0-100%). On and off switching points can be set freely and independently of each other in %, enabling any number of switching functions. They can also be overridden manually at any time at the touch of a button. Application example: Automatic protection of the battery against harmful deep discharge, the consumers are switched off exactly according to the state of charge, e.g. at less than 25% state of charge How is the battery computer connected? A plug-in connection cable connects the LCD display completely to a robust precision measuring resistor (shunt), which is connected directly to the negative terminal of the on-board battery and at which the battery voltages and currents are recorded. The switching output for connecting signal transmitters or powerful switching relays is also located here. Can I also use a different shunt? The display is supplied with a suitable measuring shunt; the devices are matched to the measuring shunts included in the scope of delivery and cannot be operated in conjunction with other measuring shunts or interchanged! Technical data Article no.: 1269 Measuring shunt: 400A LiFePO4 battery voltage: 12.8-13.2 V / 25.6-6.4 V Current consumption: 8mA Battery nominal capacity, adjustable: 50-2000 Ah Current consumption of the lighting (can be switched off): 60 mA Current measuring range shunt / continuous: 400A Current measuring range shunt / 15 min.: 600A Current measuring range shunt / 7 min.: 1800A Test mark: CE, E-test (EMC/vehicle directive) Dimensions: W80 x H85 x D24 mm Installation dimensions: W66 x H72 x D22 mm Shunt dimensions: W135 x H30 x D42mm Display weight. 55g Weight of smart shunt: 245g Scope of delivery: Display unit Measuring shunt 400A Smart-Shunt cover Connection cable 5m long Ground strap Fixing screws Instruction manual Drilling template

Effective battery charging and monitoring for motorhomes, caravans, boats and self-sufficient solar systems! How much charge does my on-board battery actually have left? Is the battery really full? Why is energy being drawn from the battery despite consumers being switched off?The VOTRONIC LCD battery computer S answers these questions to the exact percentage (%) and ampere hour (Ah). At the touch of a button, it provides comprehensive information on the current charge status of the battery, the battery currents flowing and the voltage level of the battery.The device is in constant contact with "its battery" and thus registers and evaluates all battery actions. All charging and discharging currents are meticulously counted, battery size, self-discharge, battery load etc. are taken into account using programmed characteristic curve fields. The remaining battery capacity is then calculated from the measured values and the battery size. The result is the correct display of the state of charge (remaining capacity, residual charge) of the on-board battery as a numerical value in ampere hours ("Ah") and in percent ("%") as well as a clear fill level bar, like a fuel gauge.The LCD battery computer S is suitable for all battery types (acid, gel, AGM, lithium adjustable) with 12V and 24 V battery voltage. Of course, the current battery voltage ("V") and the current battery current ("A") are also available in the display. Discharge currents (consumers) are indicated by a minus sign. Charging currents are also indicated by a clearly legible "Charge" symbol. Independently of this, there is a further display option for the voltage of a second battery, e.g. for monitoring the vehicle's starter battery.A plug-in connection cable connects the display completely to a robust precision measuring resistor (shunt), which is connected directly to the negative terminal of the on-board battery and at which the voltages and currents of the battery are recorded.The following values are measured: On-board battery voltage Battery voltage starter battery Battery current (charging ="+"; discharging ="-") Load from consumers Battery capacity "Ah" (remaining charge in ampere hours) Battery capacity "%" (remaining charge in percent) Switching output (freely programmable) Flashing warning display in the event of undervoltage or overvoltage Can I also program the battery computer? The LCD battery computer S has a freely programmable switching output for control, monitoring and warning purposes, e.g. to automatically switch loads or issue a warning depending on the charge status of the on-board battery (0-100%). On and off switching points can be set freely and independently of each other in %, enabling any number of switching functions. They can also be overridden manually at any time at the touch of a button. Application example: Automatic protection of the battery against harmful deep discharge, the consumers are switched off exactly according to the state of charge, e.g. at less than 25% state of charge How is the battery computer connected? A plug-in connection cable connects the LCD display completely to a robust precision measuring resistor (shunt), which is connected directly to the negative terminal of the on-board battery and to which the voltages and currents of the battery are recorded. The switching output for connecting signal transmitters or powerful switching relays is also located here. Can I also use a different shunt? The display is supplied with a suitable measuring shunt; the devices are matched to the measuring shunts included in the scope of delivery and cannot be operated in conjunction with other measuring shunts or interchanged! Technical data: Measuring shunt: 100A LiFePO4 battery voltage: 12.8-13.2 V / 25.6-6.4 V Current consumption: 8mA Battery nominal capacity, adjustable: 50-2000 Ah Current consumption of the lighting (can be switched off): 60 mA Current measuring range shunt / continuous: 100A Current measuring range shunt / 15 min.: 150A Current measuring range shunt / 7 min.: 450A Test mark: CE, E-test (EMC/vehicle directive) Dimensions: W80 x H85 x D24 mm Installation dimensions: W66 x H72 x D22 mm Shunt dimensions: W135 x H30 x D42mm Display weight. 55g Weight of smart shunt: 240g Scope of delivery: Display unit Measuring shunt 100A Smart shunt cover Connection cable 5m long Ground strap Fixing screws Instruction manual Drilling template

The fresh water tank gauge S from Votronic (MPN 5311) was designed for precise level measurement and can be used for all tank materials and tank sizes. The tank level is visualized via a 3-colour scalar, which is displayed on 10 LEDs, each representing 10% of the tank content. The display works continuously, as intermediate levels are displayed with variable brightness and therefore trends can be recognized immediately.The fresh water tank display S is designed as a panel version to match the VOTRONIC modular system and fits in perfectly with other VOTRONIC display units (uniform height 85 mm). Of course, it is also possible to retrofit a single display in the vehicle. Small front panel dimensions and the particularly low installation depth of just 18 mm allow installation in almost any location. The indicator is protected against reverse polarity and overload and is easy to connect via screw terminals on the back of the device.Key product features of the fresh water tank indicator S, 5311 Suitable for 12V and 24V DC operating voltage Low current consumption: only 1 - 30 mA Test mark: E-test, (EMC/vehicle directive) Panel dimensions WxHxD: 47 x 85 x 20 mm Installation dimensions: 29 x 63 x 18 mm Can be switched on and off at the touch of a button High display resolution of the tank level thanks to 10-stage display Suitable for the Votronic module system Can also be operated with 2 tank sensorsThe display units can also be assigned to 2 tanks (e.g. indoor/outdoor tank, summer/winter operation, additional tank, etc.). Single switches 2xUM are suitable for switching, e.g. switch panel 16 A S art. no. 1289 or switch panel 2x16 A S art. no. 1291Compatible with many Votronic tank sensors Tank electrode 12-24 K, 5543 Tank electrode 15-50 K, 5545 Tank electrode 20 K-WC, 5555 Tank sensor FL, 5530 Tank sensor 30-110 K-FL, 5551 Scope of delivery:1x Votronic 5311 fresh water tank display S1x set of fixing screws1x drilling template1x Operating instructions

The Votronic USB Charger Panel S (MPN 1297) has been specially developed for use in motorhomes. This panel offers you the option of charging devices via a USB connection. The panel has two USB ports, each with 5V / 2.5A. The panel is connected using the flat plugs supplied. Important product features: USB dual charger 2 connections with 5V / 2.5A each Dimensions 85x47x42mm The Votronic USB charger 5V 2.5A for installation in motorhomes is just one part of a whole series of coordinated panels. In addition to the USB panels, the Votronic switch and fuse panel series also offers panels for switches, main switches and fuses, as well as a socket outlet panel. An internationally understandable labeling sheet is available for labeling the panel. The pictogram foil is self-adhesive, abrasion-resistant and corresponds to the Votronic front panel design in terms of size and font. Scope of delivery: 1x Votronic 1297 built-in USB charging panel 5V 2.5A

The Votronic socket outlet panel S (MPN 1293) was specially developed for use in motorhomes. This panel enables the connection of 12V consumers with a maximum consumption of 8A via a cigarette lighter plug or adapter. The panel itself is connected using the flat plugs supplied. Important product features: Connection of 12V consumers via DIN plug (ISO 4165) Maximum current 8A Connection of the panel via blade terminals Dimensions 47x85x65mm The socket outlet panel for installation in motorhomes is just one part of a whole series of coordinated panels. In addition to the socket outlet, the Votronic switch and fuse panel series also offers panels for switches, main switches and fuses as well as a USB port. An internationally understandable labeling sheet is available for labeling the panel. The pictogram foil is self-adhesive, abrasion-resistant and corresponds to the Votronic front panel design in terms of size and font. Scope of delivery: 1x Votronic 1293 socket outlet installation panel