The Votronic switch panel 4S 12/24 (MPN 1288) for 12V & 24V systems has been specially developed for use in motorhomes. This panel is equipped with four separate ON/OFF switches with which you can activate or deactivate different consumer groups individually. Each switch has its own indicator LED and a maximum load of 8A. Switch panel 4 S 4 ON/OFF switches, each with a load capacity of 8A, with indicator LEDConnection via screw terminalsThe connections are designed for cable cross-sections up to 4 mm²The VOTRONIC switch panel 4S 12/24 is suitable for both 12 V and 24 V Scope of delivery: 1x Votronic 1288 switch panel 4S 12/24

With the main switch / battery selector switch, two batteries can be switched on and off simultaneously and controlled separately to reduce power consumption when the device, vehicle or boat is not in use. The switch is suitable for automotive electronics, electrical products and all types of 12V/24V/36V vehicles, boats, motorhomes, etc.The practical rotary switch is very easy to operate and works smoothly. With switch position 1 or 2 one of the connected batteries can be switched on, with 1 & 2 both are connected to the circuit and OFF (red) means both batteries are switched off. When the device or vehicle is not in use, the switch can be used to safely disconnect the connection between the battery and the electrical product, thus reducing energy consumption. Features Suitable for 12V/24V/36VContinuous current 12V DC: 200AIntermittent current 12V DC: 300AMaximum current (short-term): 1000AWeight: 260gSelector switch dimensions: 69 x 69 x 74mmDimensions for the 4 removable cable glands: 45 x 20mmConnection terminal: M8 Guard and locking service The switch can be used as an independent unit or in parallel with other switches. It can effectively protect the power supply, reduce battery loss and extend battery life. The switch is non-removable. Durable material The selector switch is made of CE-certified, high-quality ABS flame-retardant reinforced nylon and silver-plated red copper bolts. It is resistant to moisture, UV and ageing and has a long service life. The rear cover is insulated to prevent short circuits, meet safety requirements and effectively prevent electrical accidents. Easy installation The battery selector switch can be installed quickly and easily. Attention must be paid to the arrangement of the positive and negative wires, then install the corresponding lining plate and tighten the four screws to prevent the cable connector from being exposed to the air and oxidized. Scope of delivery: 1x battery switch4x removable side plate1x base plate4x screw4x nut

The Votronic switch panel 16A S (MPN 1289) for 12V and 24V systems has been specially developed for use in motorhomes. With the integrated individual switch, connected consumer groups can be easily switched on or off. The switch can be loaded with 2x 8A or 1x 16A. Important product features: Single switch 2xUM with flat plug connectionLoad capacity: max. 2x 8A or 1x 16ASuitable for 12V and 24V systems The 16 A switch panel is part of the Votronic switch and fuse panel series which, in addition to panels for switches, main switches and fuses, also includes a USB port panel and a socket outlet panel in the same design. An internationally understandable labeling sheet is available for labeling the panel. The pictogram foil is self-adhesive, abrasion-resistant and corresponds to the Votronic front panel design in terms of size and font. Scope of delivery: 1x Votronic 1289 single switch panel 16A S 12V

With the battery disconnect switch, your battery can be safely disconnected to reduce power consumption when the device, vehicle or boat is not in use. The switch is suitable for automotive electronics, electrical products and all types of 12V/24V vehicles, boats, motorhomes, etc. The practical rotary switch is very easy to use and works smoothly. ON (green) means switching on the circuit and OFF (red) means switching off. Switch the power supply on or off safely to avoid electric shock. Features Suitable for 12V / 24VContinuous current 12V DC: 275AIntermittent current 12V DC: 455AInstantaneous current 12V DC: 1250AWeight: 260gDimensions of disconnector: 69 x 69 x 75mmDimensions for the 4 removable cable glands: 45 x 20mm Guard and locking service The switch can be used as an independent unit or in parallel with other switches. It can effectively protect the power supply, reduce battery loss and extend battery life. Durable material The disconnect switch is made of CE-certified, high-quality ABS flame-retardant reinforced nylon and silver-plated red copper bolts. It is resistant to moisture, UV and ageing and has a long service life. The rear cover is insulated to prevent short circuits, meet safety requirements and effectively prevent electrical accidents. Easy installation The battery isolator can be installed quickly and easily. Attention must be paid to the arrangement of the positive and negative wires, then install the corresponding lining plate and tighten the four screws to prevent the cable connector from being exposed to the air and oxidized. Scope of delivery: 1x battery switch1x bottom cover4x screws + nuts for fastening

The VOTRONIC Battery Protector 40 is connected between the supply battery and the consumer and is suitable for all lead-acid battery types (acid, gel, AGM) and makes. They protect the battery from dangerous deep discharge as well as the consumers and equipment from undervoltage and overvoltage and, controlled by an external switch, can also serve as a remote-controlled battery master switch. The reset to normal operation takes place automatically as soon as the voltage has risen again, e.g. to 12.5 V, due to battery recovery or brief charging. The switch-off can also be canceled manually using the "EMERGENCY ON" function. The Battery Protector 40 can be operated remotely via the "Sensor +" terminal using a simple switch (1-pole ON / OFF). This makes it a powerful battery main switch. The EMERGENCY ON function can also be operated remotelyImportant product features Switching current 40 A, briefly overloadable up to 60 A, externally visible switching status display EMERGENCY STOP function via switch on the device, can also be operated remotely via external switch Automatic reset as soon as the battery voltage returns to the normal range (charging) Separate sensor cable and switching thresholds with hysteresis and timer functions for trouble-free operation Bistable power relay, very low power consumption, less than 3 mA (according to EN 13976) No self-consumption when switched off via external switch, e.g. remote control as main battery switch Solid screw terminals for battery and load cable cross-sections up to 10 mm² "Motor" version with higher switch-off thresholds maintains the starting capability of emergency vehicles with only one battery circuit in accordance with DIN EN 1789 Technical data MPN 3075 Operating voltage: 12V Switching current (continuous/short): 40A/60A Switching threshold undervoltage: 10.7V Undervoltage reset point: 12.8V Overvoltage protection (off/on): 15.5V / 15V Weight: 97 grams

The Votronic switch panel 2 x 16 A S (MPN 1291) for 12V and 24V systems has been specially developed for use in motorhomes. The integrated individual switches can be used to switch connected consumer groups on or off separately. The switches can each be loaded with 2x 8A or 1x 16A. Important product features: 2 individual switches 2xUM with flat plug connection Load capacity: max. 2x 8A or 1x 16A Suitable for 12V and 24V systemsDimensions: 47 x 85 x 25 mm The switch panel 2 x 16 A is part of the Votronic switch and fuse panel series which, in addition to panels for switches, main switches and fuses, also includes a USB port panel and a socket outlet panel with the same look. Scope of delivery: 1x Votronic 1291 switch panel 2x 16A 12V/24V

The VOTRONIC Battery Protector 40 Motor is connected between the supply battery and the consumer and is suitable for all lead-acid battery types (acid, gel, AGM) and makes. They protect the battery from dangerous deep discharge as well as the consumers and equipment from undervoltage and overvoltage and, controlled by an external switch, can also serve as a remote-controlled battery master switch. Compared to the "normal" Battery Protector 40, the motor version switches to undervoltage at 11.8V. The reset to normal operation takes place automatically as soon as the voltage has risen again, e.g. to 12.5 V, due to battery recovery or brief charging. The switch-off can also be canceled manually using the "EMERGENCY ON" function. The Battery Protector 40 can be operated remotely via the "Sensor +" terminal using a simple switch (1-pole ON / OFF). This makes it a powerful battery main switch. The EMERGENCY ON function can also be operated remotely Important product features Switching current 40 A, briefly overloadable up to 60 A, externally visible switching status displayEMERGENCY STOP function via switch on the device, can also be operated remotely via external switchAutomatic reset as soon as the battery voltage returns to the normal range (charging)Separate sensor cable and switching thresholds with hysteresis and timer functions for trouble-free operationBistable power relay, very low power consumption, less than 3 mA (according to EN 13976)No self-consumption when switched off via external switch, e.g. remote control as main battery switchSolid screw terminals for battery and load cable cross-sections up to 10 mm²"Motor" version with higher switch-off thresholds maintains the starting capability of emergency vehicles with only one battery circuit in accordance with DIN EN 1789Technical data MPN 3075Operating voltage: 12VSwitching current (continuous/short): 40A/60ASwitching threshold undervoltage: 11.8VUndervoltage reset point: 12.8VOvervoltage protection (off/on): 15.5V / 15VWeight: 97 grams

The Votronic main switch panel 20A S (MPN 1295) was specially developed for use in motorhomes. This panel serves as a main switch for connected consumers or consumer groups. It has a 20A overcurrent switch which is automatically reset to the 0 position if the continuous current exceeds 20A (thermal tripping). Important product features: Main switch with 20A overcurrent switch Thermally triggered overload protection ensures safety on board, can be overloaded for a short time tripping at more than 20A continuous current with return of the switch to the 0 position Suitable for 12V and 24V systems Quality made in Germany The Votronic main switch panel with 20A switching capacity and a smart look is designed for installation in motorhomes. It is just one part of a whole series of coordinated panels. In addition to the main switch, the Votronic switch and fuse panel series also offers panels for switches, main switches and fuses, as well as a socket outlet panel. An internationally understandable labeling sheet is available for labeling the panel. The pictogram foil is self-adhesive, abrasion-resistant and corresponds to the Votronic front panel design in terms of size and font. Scope of delivery: 1x Votronic 1295 main switch panel 20A S 12V 24V with thermal fuse

The Votronic 2200 battery cut-off relay separates the starter battery from the board battery after the engine has been switched off and switches both back in parallel after the next engine start. This ensures that the board battery is also charged via the alternator while driving, while it can be discharged independently of the starter battery when stationary. Technical features at a glance: max. switching capacity: 70A at 12V Vehicles with 2 separate battery circuits (starter + board battery) Dimensions: 26x26x42mm incl. mounting flange Not suitable for vehicles according to Euro 6 standard Scope of delivery 1x Votronic 2200 battery cut-off relay 12V / 70A 1x blade terminals 1x operating instructions

Battery switch / battery isolator 6V- 24V 100A Natoknochen

The Votronic socket outlet panel S (MPN 1293) was specially developed for use in motorhomes. This panel enables the connection of 12V consumers with a maximum consumption of 8A via a cigarette lighter plug or adapter. The panel itself is connected using the flat plugs supplied. Important product features: Connection of 12V consumers via DIN plug (ISO 4165) Maximum current 8A Connection of the panel via blade terminals Dimensions 47x85x65mm The socket outlet panel for installation in motorhomes is just one part of a whole series of coordinated panels. In addition to the socket outlet, the Votronic switch and fuse panel series also offers panels for switches, main switches and fuses as well as a USB port. An internationally understandable labeling sheet is available for labeling the panel. The pictogram foil is self-adhesive, abrasion-resistant and corresponds to the Votronic front panel design in terms of size and font. Scope of delivery: 1x Votronic 1293 socket outlet installation panel

The Votronic 200A cut-off relay (MPN 2201) separates the starter battery from the on-board battery after the engine has been switched off and switches both back in parallel after starting to charge the alternator. The cut-off relay is also an excellent addition to the VBCS Triple series. Powerful version with max. 200A load capacity and equipped with a spark suppression diode. System voltage: 12V Power connections M6 screw bolt; control connections: Spade connector 6.3 mm. Mounting flange - without connections. Complete with blade terminals! Dimensions: Dimensions: 45 x 45 x 63 mm Scope of delivery: 1x Votronic 2201 cut-off relay 1x operating instructions

The Votronic USB Charger Panel S (MPN 1297) has been specially developed for use in motorhomes. This panel offers you the option of charging devices via a USB connection. The panel has two USB ports, each with 5V / 2.5A. The panel is connected using the flat plugs supplied. Important product features: USB dual charger 2 connections with 5V / 2.5A each Dimensions 85x47x42mm The Votronic USB charger 5V 2.5A for installation in motorhomes is just one part of a whole series of coordinated panels. In addition to the USB panels, the Votronic switch and fuse panel series also offers panels for switches, main switches and fuses, as well as a socket outlet panel. An internationally understandable labeling sheet is available for labeling the panel. The pictogram foil is self-adhesive, abrasion-resistant and corresponds to the Votronic front panel design in terms of size and font. Scope of delivery: 1x Votronic 1297 built-in USB charging panel 5V 2.5A

The VOTRONIC 6075 Battery Protector 40 24 is connected between the supply battery and the consumer and is suitable for all lead-acid battery types (acid, gel, AGM) and makes. They protect the battery from dangerous deep discharge as well as the consumers and equipment from undervoltage and overvoltage and, controlled by an external switch, can also serve as a remote-controlled battery master switch The reset to normal operation takes place automatically as soon as the voltage has risen again, e.g. to 25 V, due to battery recovery or brief charging. The switch-off can also be canceled manually using the "EMERGENCY ON" function. The Battery Protector 40 can be operated remotely via the "Sensor +" terminal using a simple switch (1-pole ON / OFF). This makes it a powerful battery main switch. The EMERGENCY ON function can also be operated remotely Important product features Switching current 40 A, briefly overloadable up to 60 A, externally visible switching status displayEMERGENCY STOP function via switch on the device, can also be operated remotely via external switchAutomatic reset as soon as the battery voltage returns to the normal range (charging)Separate sensor cable and switching thresholds with hysteresis and timer functions for trouble-free operationBistable power relay, very low power consumption, less than 3 mA (according to EN 13976)No self-consumption when switched off via external switch, e.g. remote control as main battery switchSolid screw terminals for battery and load cable cross-sections up to 10 mm²"Motor" version with higher switch-off thresholds maintains the starting capability of emergency vehicles with only one battery circuit in accordance with DIN EN 1789Technical data MPN 6075Operating voltage: 24VSwitching current (continuous/short): 40A/60ASwitching threshold undervoltage: 21.4VUndervoltage reset point: 25VOvervoltage protection (off/on): 31V/30VWeight: 97 gramsDimensions (W x H x D) 90 x 38 x 60 mm

With the main switch / battery selector switch, two batteries can be switched on and off simultaneously and controlled separately to reduce power consumption when the device, vehicle or boat is not in use. The switch is suitable for automotive electronics, electrical products and all types of 12V/24V/36V vehicles, boats, motorhomes, etc.The practical rotary switch is very easy to operate and works smoothly. With switch position 1 or 2 one of the connected batteries can be switched on, with 1 & 2 both are connected to the circuit and OFF (red) means both batteries are switched off. When the device or vehicle is not in use, the switch can be used to safely disconnect the connection between the battery and the electrical product, thus reducing energy consumption. Features Suitable for 6V/12V/24V/36V Continuous current 12V DC: 175A Intermittent current 12V DC: 300A Maximum current (short-term): 1000A Weight: 260g Selector switch dimensions: 134 x 134 x 77mm Connection terminal: M5 Guard and locking service The switch can be used as an independent unit or in parallel with other switches. It can effectively protect the power supply, reduce battery loss and extend battery life. The switch is non-removable. Durable material The selector switch is made of CE-certified, high-quality ABS flame-retardant reinforced nylon and silver-plated red copper bolts. It is resistant to moisture, UV and ageing and has a long service life. The rear cover is insulated to prevent short circuits, meet safety requirements and effectively prevent electrical accidents. Easy installation The battery selector switch can be installed quickly and easily. Pay attention to the arrangement of the positive and negative wires, then install the corresponding lining plate and tighten the four screws to prevent the cable connector from being exposed to the air and oxidized.

The Votronic 12 V 60 A changeover relay is a switching relay with NC contact (normally closed contact) for connecting a VBCS Triple battery charger to an existing Schaudt electrical block (EBL). Supplied complete with 9.5 mm or 6.3 mm blade receptacles Dimensions: 33 x 29 x 41 mm incl. mounting flange - without connections

BA18-K Battery isolator switch (motorcycle) 62 x 25 x 38mm Max. 160A / 10 sec. - Mini design - Fully insulated housing - Flex. Mounting between negative pole and vehicle 200 mm / 6 mm2 jumper cable included in scope of delivery

With the battery disconnect switch, your battery can be safely disconnected to reduce power consumption when the device, vehicle or boat is not in use. The switch is suitable for automotive electronics, electrical products and all types of 12V/24V vehicles, boats, motorhomes, etc. The practical rotary switch is very easy to use and works smoothly. ON (green) means switching on the circuit and OFF (red) means switching off. Switch the power supply on or off safely to avoid electric shock. Features Suitable for 12V / 24VContinuous current 12V DC: 275AIntermittent current 12V DC: 455AInstantaneous current 12V DC: 1250AWeight: 260gDimensions of disconnector: 69 x 69 x 75mmDimensions for the 4 removable cable glands: 45 x 20mm Guard and locking service The switch can be used as an independent unit or in parallel with other switches. It can effectively protect the power supply, reduce battery loss and extend battery life. Durable material The disconnect switch is made of CE-certified, high-quality ABS flame-retardant reinforced nylon and silver-plated red copper bolts. It is resistant to moisture, UV and ageing and has a long service life. The rear cover is insulated to prevent short circuits, meet safety requirements and effectively prevent electrical accidents. Easy installation The battery isolator can be installed quickly and easily. Attention must be paid to the arrangement of the positive and negative wires, then install the corresponding lining plate and tighten the four screws to prevent the cable connector from being exposed to the air and oxidized. Scope of delivery: 1x battery switch1x bottom cover4x screws + nuts for fastening

Battery disconnector 6 V, 12 V, 24 V The battery isolating switch is suitable for preventing short circuits and unwanted battery discharge. The battery disconnector is connected to the negative terminal. Advantages: Max. Max. load capacity: 100 A Operating voltage: 6 Volt/ 12 Volt/ 24 Volt Size (LxWxH): approx. 8.5 x 3.5 x 3.5 cm Single-pole battery isolating switch Interrupts the entire circuit by simply turning the knob Prevents battery discharge, electrical fires, unauthorized operation, etc. Battery disconnect switch is connected to the pole Avoids tedious unscrewing of battery cables when charging Quick and easy installation Application: MOTOR VEHICLES Caravan and motorhome

The Votronic switch panel 4S 12/24 (MPN 1288) for 12V & 24V systems has been specially developed for use in motorhomes. This panel is equipped with four separate ON/OFF switches with which you can activate or deactivate different consumer groups individually. Each switch has its own indicator LED and a maximum load of 8A. Switch panel 4 S 4 ON/OFF switches, each with a load capacity of 8A, with indicator LEDConnection via screw terminalsThe connections are designed for cable cross-sections up to 4 mm²The VOTRONIC switch panel 4S 12/24 is suitable for both 12 V and 24 V Scope of delivery: 1x Votronic 1288 switch panel 4S 12/24

VOTRONIC Switch Unit 40 dient als Haupt Ein- und Ausschalter für ihr 12 / 24 Volt - Bordnetz und kann mit einem eigengen Schalter bedient werden.VOTRONIC Switch Unit 40 arbeitet auf der Basis eines bistabilen Leistungsrelais. Sein Eigenverbrauch ist äußerst gering. Er ist besonders als ferngesteuerter Hauptschalter oder als Lastrelais, das lange Zeit eingeschaltet bleiben soll, geeignet. Die Strombelastbarkeit beträgt 40 A.Switch Unit 40 kann durch einen einfachen Schalter (1pol. EIN / AUS) fernbedient werden. Der Schalter wird nur sehr gering belastet (0,002 A), so dass auch eine Miniaturausführung ausreichend ist.Zudem können über eine NOT-EIN-Funktion (EMERGENCY-Schalter) die Verbraucher auch manuell am Relais ein- bzw. ausgeschaltet werden.Bei Schalter „AUS“ ist die gesamte Elektronik komplett abgeschaltet; der ohnehin sehr geringe Eigenstromverbrauch der Switch Unit 40 entfällt dann ganz.In der Bedienungsanleitung befindet sich ein leicht verständlicher Schaltplan wie die Schalteinheit in ihr Netz integriert wird.Der Einsatzbereich erstreckt sich über Wohnmobile, Boote bis hin zu Einsatzfahrzeugen:Betriebsspannung: 12 V / 24 VBetriebstemperaturbereich: -20° ... +50°CEigenverbrauch: 3 mAFür Kabelquerschnitt: 2,5 - 10 mm²Gewicht: 97 gHersteller: VotronicKategoriename: Zubehör LadereglerLuftfeuchtigkeit: max. 95 % RF (nicht kondensierend)Produkttyp 1: BatterieschalterRoHS Konform: JaSchutzart (IP): IP21Zertifizierung: E-Prüfung (EMV/Kfz-Richtlinie)Lieferumfang: Switch Unit 40, Betriebsanleitung

Die VOTRONIC Switch Unit 100 dient als Haupt Ein- und Ausschalter für ihr 12 / 24 Volt - Bordnetz und kann mit einem eigengen Schalter bedient werden.Die Switch Unit arbeitet auf der Basis eines bistabilen Leistungsrelais. Sein Eigenverbrauch ist äußerst gering. Er ist besonders als ferngesteuerter Hauptschalter oder als Lastrelais, das lange Zeit eingeschaltet bleiben soll, geeignet. Die Strombelastbarkeit beträgt 100 A.Die Switch Unit 100 kann durch einen einfachen Schalter (1pol. EIN / AUS) fernbedient werden. Der Schalter wird nur sehr gering belastet (0,003 A), so dassauch eine Miniaturausführung ausreichend ist.Zudem können über eine NOT-EIN-Funktion „Relais manuell“die Verbraucher auch direkt am Relais ein-bzw. ausgeschaltet werden.Der Einsatzbereich erstreckt sich über Wohnmobile und Boote bis hin zu Einsatzfahrzeugen.In der Bedienungsanleitung befindet sich ein leicht verständlicher Schaltplan wie die Schalteinheit in ihr Netz integriert wird.Lieferumfang: Votromic Switch Unit 100, Bedienungsanleitung, 2 Schutzkappen.Betriebsspannung: 12 V / 24 VBetriebstemperaturbereich: -20° ... +50°CEigenverbrauch: 3 mAFür Kabelquerschnitt: 2,5 - 10 mm²Gewicht: 180 gHersteller: VotronicKategoriename: Zubehör LadereglerLuftfeuchtigkeit: max. 95 % RF (nicht kondensierend)Produkttyp 1: BatterieschalterRoHS Konform: JaSchutzart (IP): IP21Zertifizierung: E-Prüfung (EMV/Kfz-Richtlinie)Lieferumfang: Switch Unit 100, Betriebsanleitung

Der VOTRONIC StandBy-Charger dient zur automatischen Nachladung und Ladeerhaltung der Starterbatterie oder der Zusatzbatterie, wenn das Netz-Ladegerät,der Solar-Laderegler oder der Generator nur über einen Ladeausgang verfügt. Das Gerät lässt sich leicht nachrüsten, indem es einfach zwischen Bord- und Startbatterie bzw. Bord- und Zusatzbatterie geschaltet wird,ohne die vorhandene Verkabelung ändern zu müssen.Mit den Standby-Charger machen Sie Ihren Laderegler im Handumdrehen zum Dual-Laderegler !Ist z.B. das Netz-Ladegerät in Betrieb und lädt die Bordbatterie, wird je nach Ladezustand mit einem kleinen Teil des Ladestroms die zweite Batterie (Startbatterie oder Zusatzbatterie) mitgeladen.Diese Ladeerhaltung arbeitet automatisch und ist durch eine erhöhte Spannungslage der zweiten Batterie erkennbar.Eine Überladung der zweiten Batterie ist ausgeschlossen, da die Ladespannung um mindestens 0,6V abgesenkt ist und der Ladestrom auf 3A (24V-Variante: 2A) begrenzt wird.Wichtige Eigenschaftenermöglicht es Standard-Ladereglern, eine zweite Batterie ebenfalls zu laden/erhalten.automatische Nachladungautomatische Ladeerhaltungeinfache Installationjederzeit ohne zusätzlichen Aufwand nachrüstbarLieferumfang: 1x Votronic 3065 StandBy-Charger 12V

Der VOTRONIC StandBy-Charger 24V (MPN 6065) dient der automatischen Nachladung und Ladeerhaltung der Starterbatterie oder der Zusatzbatterie, wenn das Netz-Ladegerät, der Solar-Laderegler oder der Generator nur über einen Ladeausgang verfügt. Das Gerät lässt sich leicht in vorhandene Systeme integrieren, indem Sie es einfach zwischen Bord- und Startbatterie bzw. Bord- und Zusatzbatterie schalten. Eine Änderung der vorhandenen Verkabelung ist dabei nicht notwendig. Der Standby-Charger macht Ihren Laderegler im Handumdrehen zum Dual-Laderegler. Ist z.B. das Netz-Ladegerät in Betrieb und lädt die Bordbatterie, wird je nach Ladezustand mit einem kleinen Teil des Ladestroms die zweite Batterie (Startbatterie oder Zusatzbatterie) mitgeladen. Diese Ladeerhaltung arbeitet automatisch und ist durch eine erhöhte Spannungslage der zweiten Batterie erkennbar. Eine Überladung der zweiten Batterie ist ausgeschlossen, da die Ladespannung um mindestens 0,6V abgesenkt ist und der Ladestrom auf 3A (24V-Variante: 2A) begrenzt wird. wichtige Merkmale des StandBy-Charger 24V, 6065 ermöglicht es Standard-Ladereglern, eine zweite Batterie ebenfalls zu laden/erhalten.automatische Nachladungautomatische Ladeerhaltungeinfache Installation, für 24V Batterienjederzeit ohne zusätzlichen Aufwand nachrüstbar Lieferumfang: Votronic 6065 StandBy-Charger 24V1x Kurzanleitung