Votronic battery charger VAC-1225 M 3A Built-in mains chargers for emergency vehicles and demanding motorhome and camper owners. Especially for rescue and emergency vehicles, the reliability of the batteries installed in the vehicle is crucial for the operational readiness of the vehicle. This is particularly the case when the batteries are subject to heavy loads from many continuous consumers, when there is not enough time to recharge them due to frequent use or when the charger is inadequately adapted to the batteries. In order to meet the special requirements of emergency vehicles, the VAC series was created in cooperation with vehicle and leading battery manufacturers.Votronic charging technology has been used for years in professional emergency vehicles such as fire engines, ambulances and coastguards! Quality - Made in Germany!The device electronics are protected against moisture and ensure safe operation in the event of severe temperature fluctuations. Continuous consumers connected to the vehicle electrical system (radios, charging trays etc.) are also supplied without impairing the charging process. The built-in charging current distributor also automatically supplies the starter battery with full charging current if required. The engine start lock can be activated via a signal output when the vehicle is connected to the mains.The devices are supplied with an 825 temperature sensor to ensure optimum charging of the batteries. The installation position is variable, thanks to a second device label included in the scope of delivery. Instead of a remote control, a waterproof LED display (see accessories) can be connected to the Remote Control connection socket, which indicates the operational readiness of the device on the outside of the vehicle.Further special features at a glance: Votronic products "Made in Germany" High charging power even for short journeys Significantly improved energy balance of the on-board battery Optimum charging characteristics for all battery types can be set using the battery selector switch (lead-acid, gel, AGM, lithium LiFePO4) Suitable for all alternators Automatic, adjustable power control ensures priority charging of the starter battery by the alternator when the vehicle electrical system is under heavy load, thus ensuring that the vehicle can be started again immediately Simple installation, no intervention in the vehicle's starter circuit required, device is connected in the charging line to the supply battery Parallel operation to increase power possible Particularly recommended for vehicles with Euro 6 standard Temperature sensor 825 already included in the scope of delivery The charging converters are also characterized by their compact design, low weight (high-frequency switching transformer, switch mode technology) and powerfully dimensioned power components. 6 operating displays provide information on the operating status of the device at all times. Recommended accessories: Votronic remote control S (2075) and remote operating display IP67 (2081)

Marine & Camping Charger 24V 20A TBB Trident BP2420The BP-SERIES battery charger is an intelligent battery charger specially designed for charging all types of lead-acid batteries, i.e. wet, gel and AGM batteries. The DIP switch can be used to select the perfect charging characteristic for each type of battery. Thanks to the high-frequency technology used, the charger is compact and can also be installed or stored in small compartments or cabinets. The charger is insulated against direct and alternating current and is equipped with overvoltage protection, an automatic multi-stage charging function and many other safety functions that reduce the risk of electric shock and fire.The BP battery charger offers an unbeatable number of additional functions and protective devices in this price segment. These include, among othersAutomatic multi-stage charging curve The BP series battery charger has an automatic charging function with up to six stages and delivers nominal current for around 75% of the charging time. This function guarantees complete, fast and safe charging of your battery.Integrated timerWhen the charge drops to a certain nominal value or the charging time preset on the timer has expired, the BP series battery charger switches from absorption charging to trickle charging.Recovery chargeThe BP series battery charger is designed for a permanent connection to the battery. To prevent possible sulphation during long-term trickle charging, the charger automatically switches to recovery charging mode after 14 days. Simultaneous charging of several batteriesThe BP series battery charger is equipped with several DC connections (the 12A model with two, the 20A, 25A and 40A models with three connections) so that several batteries can be charged simultaneously. The total current (12 A, 20 A, 25 A or 40 A) depends on the model type. If several batteries are connected to the charger, the total current is divided between the individual batteries according to the degree of discharge.Insulated outputsThe outputs are electrically isolated from each other. This prevents current flows between the connections and a return current from the battery to the battery charger.Particularly low-noise designThe charger is particularly low-noise. If the charging current falls below a certain value, the charger's fan is switched off. If the temperature inside the device rises again, the fan is automatically switched on again.Simultaneous operation as charger and mains adapterThe intelligent BP series battery charger can be used simultaneously as a DC mains adapter and battery charger. The device software is programmed to prevent overcharging of the battery even under such circumstances.Protective coating of the circuit boardsTo protect against moisture and corrosion, the circuit boards installed in the BP series battery charger have a protective coating.Use as a power supply unitThe BP series battery charger can also be used as a power supply unit by setting the DIP switch accordingly. In this case, however, a constant voltage is supplied. In this mode, the device is not suitable for charging rechargeable batteries. The battery type and battery temperature are ignored in this mode. The temperature sensor does not initiate voltage equalization in this mode, but the overtemperature protection continues to function. In this mode, the charger can deliver net DC voltages of 13.5 V (12 V models) or 27 V (24 V models).Integrated protective functionsThe BP series battery charger has the following protective functions:1) Shutdown in the event of a short circuit at the output;2) Electronic protection against incorrect polarity;3) Shutdown if the battery voltage is too high;4) Power reduction if the charger temperature is too high, maintaining the temperature at a balanced level;5) Shutdown if the battery temperature is too high, automatic restart after sufficient cooling downAutomatic temperature compensationThe standard equipment of the BP series battery charger also includes a battery temperature sensor. If this sensor is connected to the battery, the charger can automatically regulate the charging current to the connected battery more precisely using appropriate temperature compensation.Operation at high ambient temperatures The BP series battery charger is designed for full-load operation at temperatures of up to 40 °CScope of delivery: Contents of the packagingIn addition to the charger, the packaging contains1) the operating instructions2) the temperature sensor

Charger 20 A with dual input and selectable charging voltage The DS250SE is a fully automatic charger with a five-stage charging process that provides up to 20 A for any lead-acid battery with a working voltage of 12 V or any lithium* type service battery from 40 to 300 Ah. It has selectable charging algorithms for AGM and lithium* batteries and can be operated via solar or alternators in parallel as well as wind power thanks to its dual input. When the service battery is fully charged, the D250SE automatically switches to trickle charging for the starter battery. The D250SE delivers a stable current of up to 20 A even in vehicles with a smart alternator and has a temperature sensor for an optimized charging process under all weather conditions. *) 12 V lithium batteries (LiFePO4, Li-Fe, Li-iron, LFP) Functions Battery disconnect function no diodes and VSR relays required Adjustable AGM mode: 14.4 V or 14.7 V maximized charging efficiency to increase battery performance and battery life Temperature sensor to optimize the charging process in cold environments Splash-proof and dust-proof (IP65) compatible with SMARTPASS 120, SMARTPASS 120S for the ultimate 140 A energy management solution

The M15 is the perfect 15 A battery charger for all boat owners. It has a variety of functions, including a Recond mode for reconditioning deeply discharged liquid and Ca/Ca batteries, as well as a temperature sensor to optimize charging at temperatures other than +25 ºC. It also has a lithium* mode for lithium* batteries. The M15 is supplied with a long 4 m cable with M10 ring terminals to facilitate boat installation. *) 12 V lithium batteries (LiFePO4, Li-Fe, Li-iron, LFP) Functions Fully automatic and easy to operate Easy to connect, spark-protected and reverse polarity protected Compact, robust design IP44 protection rating for outdoor use

Charging larger watercraft batteries The M25 is the perfect 25A battery charger for all boat owners. It has a variety of features, including a Recond mode for reconditioning deeply discharged liquid and Ca/Ca batteries, as well as a temperature sensor to optimize charging at temperatures other than +25 ºC. It also has a lithium* mode for lithium* batteries. The M25 is supplied with a long 4 m cable with M10 ring terminals to facilitate boat installation. *) 12 V lithium batteries (LiFePO4, Li-Fe, Li-iron, LFP) Functions Fully automatic and easy to operate Easy to connect, spark-protected and reverse polarity protected Compact, robust design IP44 protection rating for outdoor use