Diese interessante Gerätekombination bestehend aus 3-fach Thermometer und genauer Quartzuhr und wird aus dem Fahrzeug-Bordnetz betrieben. Hervorzuheben ist der geringe Stromverbrauch der Einheit sowie die große LCD-Anzeige, die auch aus weiterer Entfernung sehr gut ablesbar ist. Bei ungünstigen Lichtverhältnissen sorgt die eingebaute weiße Hinterleuchtung des Displays für eine gute Ablesbarkeit. Der Thermometerteil misst die Raumtemperatur durch den im Gerät eingebauten Sensor. Zusätzlich ist die externe Fernmessung durch den mitgelieferten Außenfühler vorgesehen. Er wird im Außenbereich z. B. unter der vorderen Stoßstange des Fahrzeugs montiert und kann hier die Außentemperatur erfassen. Ein weiterer externer Messeingang 3 ist beispielsweise zur Überwachung der Medikamentenaufbewahrung, von Kühlboxen oder Wärmeboxen etc. hervorragend geeignet. Bei einer Messauflösung von 0,1°C betragen die Messbereiche aller Sensoren -30°C bis +70°C. Der Uhrenteil umfasst die Anzeige Minuten und Stunden im 24 Stunden Anzeigeformat und den blinkenden Doppelpunkt zur Funktionskontrolle. In der unteren Zeile kommt der Wochentag zur Anzeige. Die Uhr arbeitet mit hoher Genauigkeit und besitzt eine Gangreserve gegen Spannungsausfall. Bei DCF-Betrieb der Uhr (DCF-Modul erforderlich) informiert die Anzeige durch ein separates Segment Lieferumfang:  - 1 Stk. LCD-Thermometer  - 1 Stk. Ext. Temperatursensor  - 4 Stk. Befestigungsschrauben  - 1 Stk. Bohrschablone  - 1 Stk. Montage- bzw. Bedienungsanleitung

LCD-Voltmeter S: Dieses digitale Messgerät bringt wahlweise die Spannung der Bord- und der Starter-Batterie zur Anzeige. Die Spannungen werden als genauer Zahlenwert dargestellt.Die zusätzliche Balkenanzeige arbeitet im Bereich von 10,5 bis 15 Volt und stellt damit den interessantesten Bereich der Batteriespannung von der Tiefentladung bis zur maximalen Ladespannung anschaulich und auf einen Blick erfassbar dar. Bei der Installation des Gerätes wird für diese Funktion einmalig auf 12V- oder 24V-Betrieb eingestellt. Bei 24V-Betrieb entspricht der Bereich dann 21,0 bis 30,0 Volt. Ein Mischbetrieb von z.B. 24V Starterkreis und 12V-Versorgungskreis ist ebenfalls möglich, da diese Einstellung separat für die Starter- und Bord-Batterie geschieht. Der Anschluss erfolgt durch Schraubklemmen auf der Rückseite des Gerätes. Passend zum VOTRONIC Modulsystem reiht sich das LCD-Voltmeter S sowohl optisch als auch mechanisch (einheitliche Höhe 85 mm) an die übrigen Anzeigemodule an und die geringe Einbautiefe von nur 22 mm erlaubt die Montage an nahezu jeder Stelle. Die Anzeige ist bei Bedarf weiß hinterleuchtet (schaltbar) und auch aus größeren Entfernungen sowie bei allen Lichtverhältnissen sehr gut ablesbar.Lieferumfang:1 St. LCD Voltmeter S (Anzeige)4 St. Befestigungsschrauben1 St. Bedienungsanleitung1 St. Bohrschablone

The LCD Charge Control S is a convenient, easy-to-use control and operating element that displays the status of the individual charging sources, the current charging phase, the voltage of the on-board and starter battery and the current charging current. In solar mode, the displays for the current solar power (W) and the energy counters (Wh and Ah, can be reset to "zero" at any time) are also available for your own statistical purposes. With the VBCS or VAC Triple, the mains charging mode can be switched on or off manually or reduced in terms of power (AC power limit) at the touch of a button, e.g. if the shore power is too weak. A special protective function ensures that an inadvertently switched off mains charge is reactivated if the on-board battery is in danger of being deeply discharged. The large, clear display has an illuminated and easy-to-read display with very low power consumption. The plug and play connection means it can be easily retrofitted at any time, even retrospectively, and its compact design means it can be installed in almost any location. The product has the following features: Compatible with VOTRONIC VBCS chargersLarge, clear displayBright, white illuminated displayDisplay of the active charging source mains/charging converter/solarControl of the mains charging function, AC power limit Display of battery charging phasesVoltage and charging current displaysSolar computer function

Effective battery charging and monitoring for motorhomes, caravans, boats and self-sufficient solar systems! How much charge does my on-board battery actually have left? Is the battery really full? Why is energy being drawn from the battery despite consumers being switched off?The VOTRONIC LCD battery computer S answers these questions to the exact percentage (%) and ampere hour (Ah). At the touch of a button, it provides comprehensive information on the current charge status of the battery, the battery currents flowing and the voltage level of the battery.The device is in constant contact with "its battery" and thus registers and evaluates all battery actions. All charging and discharging currents are meticulously counted, battery size, self-discharge, battery load etc. are taken into account using programmed characteristic curve fields. The remaining battery capacity is then calculated from the measured values and the battery size. The result is the correct display of the state of charge (remaining capacity, residual charge) of the on-board battery as a numerical value in ampere hours ("Ah") and in percent ("%") as well as a clear fill level bar, like a fuel gauge.The LCD battery computer S is suitable for all battery types (acid, gel, AGM, lithium adjustable) with 12V and 24 V battery voltage. Of course, the current battery voltage ("V") and the current battery current ("A") are also available in the display. Discharge currents (consumers) are indicated by a minus sign. Charging currents are also indicated by a clearly legible "Charge" symbol. Independently of this, there is a further display option for the voltage of a second battery, e.g. for monitoring the vehicle's starter battery.A plug-in connection cable connects the display completely to a robust precision measuring resistor (shunt), which is connected directly to the negative terminal of the on-board battery and at which the voltages and currents of the battery are recorded.The following values are measured: On-board battery voltage Battery voltage starter battery Battery current (charging ="+"; discharging ="-") Load from consumers Battery capacity "Ah" (remaining charge in ampere hours) Battery capacity "%" (remaining charge in percent) Switching output (freely programmable) Flashing warning display in the event of undervoltage or overvoltage Can I also program the battery computer? The LCD battery computer S has a freely programmable switching output for control, monitoring and warning purposes, e.g. to automatically switch loads or issue a warning depending on the charge status of the on-board battery (0-100%). On and off switching points can be set freely and independently of each other in %, enabling any number of switching functions. They can also be overridden manually at any time at the touch of a button. Application example: Automatic protection of the battery against harmful deep discharge, the consumers are switched off exactly according to the state of charge, e.g. at less than 25% state of charge How is the battery computer connected? A plug-in connection cable connects the LCD display completely to a robust precision measuring resistor (shunt), which is connected directly to the negative terminal of the on-board battery and to which the voltages and currents of the battery are recorded. The switching output for connecting signal transmitters or powerful switching relays is also located here. Can I also use a different shunt? The display is supplied with a suitable measuring shunt; the devices are matched to the measuring shunts included in the scope of delivery and cannot be operated in conjunction with other measuring shunts or interchanged! Technical data: Measuring shunt: 100A LiFePO4 battery voltage: 12.8-13.2 V / 25.6-6.4 V Current consumption: 8mA Battery nominal capacity, adjustable: 50-2000 Ah Current consumption of the lighting (can be switched off): 60 mA Current measuring range shunt / continuous: 100A Current measuring range shunt / 15 min.: 150A Current measuring range shunt / 7 min.: 450A Test mark: CE, E-test (EMC/vehicle directive) Dimensions: W80 x H85 x D24 mm Installation dimensions: W66 x H72 x D22 mm Shunt dimensions: W135 x H30 x D42mm Display weight. 55g Weight of smart shunt: 240g Scope of delivery: Display unit Measuring shunt 100A Smart shunt cover Connection cable 5m long Ground strap Fixing screws Instruction manual Drilling template

The LCD Charge Control S is a convenient, easy-to-use control and operating element that displays the status of the individual charging sources, the current charging phase, the voltage of the on-board and starter battery and the current charging current. In solar mode, the displays for the current solar power (W) and the energy counters (Wh and Ah, can be reset to "zero" at any time) are also available for your own statistical purposes. With the VBCS or VAC Triple, the mains charging mode can be switched on or off manually or reduced in terms of power (AC power limit) at the touch of a button, e.g. if the shore power is too weak. A special protective function ensures that an inadvertently switched off mains charge is reactivated if the on-board battery is in danger of being deeply discharged. The large, clear display has an illuminated and easy-to-read display with very low power consumption. The plug and play connection means it can be easily retrofitted at any time, even retrospectively, and its compact design means it can be installed in almost any location. The product has the following features: Compatible with VOTRONIC VBCS chargersLarge, clear displayBright, white illuminated displayDisplay of the active charging source mains/charging converter/solarControl of the mains charging function, AC power limit Display of battery charging phasesVoltage and charging current displaysSolar computer function

Effective battery charging and monitoring for motorhomes, caravans, boats and self-sufficient solar systems! How much charge does my on-board battery actually have left? Is the battery really full? Why is energy being drawn from the battery despite consumers being switched off?The VOTRONIC LCD battery computer S answers these questions to the exact percentage (%) and ampere hour (Ah). At the touch of a button, it provides comprehensive information on the current charge status of the battery, the battery currents flowing and the voltage level of the battery.The device is in constant contact with "its battery" and thus registers and evaluates all battery actions. All charging and discharging currents are meticulously counted, battery size, self-discharge, battery load etc. are taken into account using programmed characteristic curve fields. The remaining battery capacity is then calculated from the measured values and the battery size. The result is the correct display of the state of charge (remaining capacity, residual charge) of the on-board battery as a numerical value in ampere hours ("Ah") and in percent ("%") as well as a clear fill level bar, like a fuel gauge.The LCD battery computer S is suitable for all battery types (acid, gel, AGM, lithium adjustable) with 12V and 24 V battery voltage. Of course, the current battery voltage ("V") and the current battery current ("A") are also available in the display. Discharge currents (consumers) are indicated by a minus sign. Charging currents are also indicated by a clearly legible "Charge" symbol. Independently of this, there is a further display option for the voltage of a second battery, e.g. for monitoring the vehicle's starter battery.A plug-in connection cable connects the display completely to a robust precision measuring resistor (shunt), which is connected directly to the negative terminal of the on-board battery and at which the voltages and currents of the battery are recorded.The following values are measured: On-board battery voltage Battery voltage starter battery Battery current (charging ="+"; discharging ="-") Load from consumers Battery capacity "Ah" (remaining charge in ampere hours) Battery capacity "%" (remaining charge in percent) Switching output (freely programmable) Flashing warning display in the event of undervoltage or overvoltage Can I also program the battery computer? The LCD battery computer S has a freely programmable switching output for control, monitoring and warning purposes, e.g. to automatically switch loads or issue a warning depending on the charge status of the on-board battery (0-100%). On and off switching points can be set freely and independently of each other in %, enabling any number of switching functions. They can also be overridden manually at any time at the touch of a button. Application example: Automatic protection of the battery against harmful deep discharge, the consumers are switched off exactly according to the state of charge, e.g. at less than 25% state of charge How is the battery computer connected? A plug-in connection cable connects the LCD display completely to a robust precision measuring resistor (shunt), which is connected directly to the negative terminal of the on-board battery and at which the battery voltages and currents are recorded. The switching output for connecting signal transmitters or powerful switching relays is also located here. Can I also use a different shunt? The display is supplied with a suitable measuring shunt; the devices are matched to the measuring shunts included in the scope of delivery and cannot be operated in conjunction with other measuring shunts or interchanged! Technical data Article no.: 1269 Measuring shunt: 400A LiFePO4 battery voltage: 12.8-13.2 V / 25.6-6.4 V Current consumption: 8mA Battery nominal capacity, adjustable: 50-2000 Ah Current consumption of the lighting (can be switched off): 60 mA Current measuring range shunt / continuous: 400A Current measuring range shunt / 15 min.: 600A Current measuring range shunt / 7 min.: 1800A Test mark: CE, E-test (EMC/vehicle directive) Dimensions: W80 x H85 x D24 mm Installation dimensions: W66 x H72 x D22 mm Shunt dimensions: W135 x H30 x D42mm Display weight. 55g Weight of smart shunt: 245g Scope of delivery: Display unit Measuring shunt 400A Smart-Shunt cover Connection cable 5m long Ground strap Fixing screws Instruction manual Drilling template

Effective battery charging and monitoring for motorhomes, caravans, boats and self-sufficient solar systems! How much charge does my on-board battery actually have left? Is the battery really full? Why is energy being drawn from the battery despite consumers being switched off?The VOTRONIC LCD battery computer S answers these questions to the exact percentage (%) and ampere hour (Ah). At the touch of a button, it provides comprehensive information on the current charge status of the battery, the battery currents flowing and the voltage level of the battery.The device is in constant contact with "its battery" and thus registers and evaluates all battery actions. All charging and discharging currents are meticulously counted, battery size, self-discharge, battery load etc. are taken into account using programmed characteristic curve fields. The remaining battery capacity is then calculated from the measured values and the battery size. The result is the correct display of the state of charge (remaining capacity, residual charge) of the on-board battery as a numerical value in ampere hours ("Ah") and in percent ("%") as well as a clear fill level bar, like a fuel gauge.The LCD battery computer S is suitable for all battery types (acid, gel, AGM, lithium adjustable) with 12V and 24 V battery voltage. Of course, the current battery voltage ("V") and the current battery current ("A") are also available in the display. Discharge currents (consumers) are indicated by a minus sign. Charging currents are also indicated by a clearly legible "Charge" symbol. Independently of this, there is a further display option for the voltage of a second battery, e.g. for monitoring the vehicle's starter battery.A plug-in connection cable connects the display completely to a robust precision measuring resistor (shunt), which is connected directly to the negative terminal of the on-board battery and at which the voltages and currents of the battery are recorded.The following values are measured: On-board battery voltage Battery voltage starter battery Battery current (charging ="+"; discharging ="-") Load from consumers Battery capacity "Ah" (remaining charge in ampere hours) Battery capacity "%" (remaining charge in percent) Switching output (freely programmable) Flashing warning display in the event of undervoltage or overvoltage Can I also program the battery computer? The LCD battery computer S has a freely programmable switching output for control, monitoring and warning purposes, e.g. to automatically switch loads or issue a warning depending on the charge status of the on-board battery (0-100%). On and off switching points can be set freely and independently of each other in %, enabling any number of switching functions. They can also be overridden manually at any time at the touch of a button. Application example: Automatic protection of the battery against harmful deep discharge, the consumers are switched off exactly according to the state of charge, e.g. at less than 25% state of charge How is the battery computer connected? A plug-in connection cable connects the LCD display completely to a robust precision measuring resistor (shunt), which is connected directly to the negative terminal of the on-board battery and at which the battery voltages and currents are recorded. The switching output for connecting signal transmitters or powerful switching relays is also located here. Can I also use a different shunt? The display is supplied with a suitable measuring shunt; the devices are matched to the measuring shunts included in the scope of delivery and cannot be operated in conjunction with other measuring shunts or interchanged! Technical data: Measuring shunt: 200A LiFePO4 battery voltage: 12.8-13.2 V / 25.6-6.4 V Current consumption: 8mA Battery nominal capacity, adjustable: 50-2000 Ah Current consumption of the lighting (can be switched off): 60 mA Current measuring range shunt / continuous: 200A Current measuring range shunt / 15 min.: 300A Current measuring range shunt / 7 min.: 900A Test mark: CE, E-test (EMC/vehicle directive) Dimensions: W80 x H85 x D24 mm Installation dimensions: W66 x H72 x D22 mm Shunt dimensions: W135 x H30 x D42mm Display weight. 55g Weight of smart shunt: 240g Scope of delivery: Display unit Measuring shunt 200A Smart shunt cover Connection cable 5m long Ground strap Fixing screws Instruction manual Drilling template

The LCD Charge Control S-VCC from Votronic (MPN 1248) is a control and operating element especially for the charging converters of the VCC series. It provides a quick and direct view of important parameters such as battery voltage, current charging current and also displays the battery charging phases. Features of the LCD Charge Control S-VCC compatible with VOTRONIC charging converters of the VCC series fits perfectly with the other Votronic display panels in terms of design, which makes for a Large, clear display Bright, white illuminated display Display of the active charging source Mains/charging converter/solar Display of the battery charging phases Voltage and charging current displays Scope of delivery: 1x Votronic 1248 LCD-Charge Control S-VCC1x Votronic 2005 control cable 5 m long1x drilling templateMounting screws, instructions