Votronic 11717 MPP 260 CI (Marine Version) 20A MPPT Solarladeregler 12V

Anschluss LCD-Solar-Computer:	JA
Anschluss Temperatur-Sensor:	JA
Ausgang EBL-Solarstromanzeige:	JA
Ausgleich der Spannungsverluste auf den Ladekabeln:	JA
Bordnetzfilter:	Ja
Dimensions (L x W x H):	131 x 77 x 40 mm
Eingangsspannungsbereich:	Vbat+5 bis 60V
Für Batterieart:	AGM (VRLA), Gel (VRLA), Li-Ion (LiFePO4), Nass (Flüssig)
Ladekennlinie:	IU1oU2
Rückstromsperre (Nachtbetrieb):	JA
Schutz gegen Überlast, Überhitzung, Verpolung:	JA
Self-consumption in [A]:	0.004
Solarmodul-Leistung max. [Wp]:	260 Wp
Solarmodul-Spannung max. [V]:	60V
Tension:	12V
Überladeschutz:	JA
Max. Ladestrom:	20A
Betriebstemperatur:	-20°C bis 45°C
Hersteller:	VOTRONIC
Modell-Reihe:	Votronic MPP CI

Votronic 1720 MPP 350 Duo Digital 21A 12V MPPT solar charge controller for two batteries

MPP solar controller specially designed for use on boats, yachts, etc. The electronics of the MPPT dual charge controller are protected against moisture. For solar modules with:up to 350 Wp module outputmax. 21 A module currentmax. 50 V module voltageCharging options: 1 supply battery and 1 starter battery Votronic solar controllers of the "MPP" (Maximum Power Point) series with "IU1oU2" charging characteristic are connected as a link between the solar panel(s) and battery(ies). With MPP technology, the controller automatically determines the maximum power output (MPP) of the solar modules several times per second. It then transforms the excess voltage of the solar module into a higher charging current for the battery (realized by high-frequency switching regulator technology with high efficiency). This additional charging current ensures shorter charging times and the best possible power utilization of the solar system.MPP solar controllers work fully automatically, are maintenance-free and offer the following functions: MPP charging current increase of 10 % to 30 % (efficiency > 95 %) compared to conventional controllers thanks to the use of state-of-the-art controller technology (microprocessor). The increase in performance is particularly noticeable at cooler times of the year and e.g. during high fog conditions, low and diffuse lighting (wintering).Switchable charging characteristics for optimum charging of gel/dryfit, AGM/non-woven or acid/wet and LiFePO4 batteries (see Table 1).The charging voltage is free of peaks and regulated in such a way that overcharging of batteries is ruled out.Two battery charging outputs:Automatic charging of the main or on-board battery (Board I).Support charging and charge retention (max. 1 A) of the vehicle starter battery (Start II) with protection against overcharging.Monitoring-free charging:Standard protection against overload, overheating, reverse polarity and reverse battery discharge (if solar power is too low, e.g. at dusk, at night, etc.).Parallel/buffer operation:Maintains charging characteristics even when loads are operated simultaneously.Overcharge protection: Regulates the charging current of the battery back if there is too much solar power and the battery is full, ensures that the battery is charged to the highest possible level by immediately recharging when power is consumed."IU1oU2" charging characteristic: Defined charging voltage increase (U1) prevents harmful acid stratification and ensures equalization charging of the individual battery cells, followed by automatic trickle charging (U2).Charging cable compensation: Voltage losses on the charging cables are automatically compensated for.On-board power supply filter: Problem-free parallel operation with wind and petrol generators, mains chargers, alternators, etc.Measurement output for EBL (electric block of the vehicle): Enables convenient use of the (solar) current display built into the electrical block to check the solar system.Switching output "AES" (only MPP250 Duo Dig. and MPP350 Duo Dig): Causes the ELECTROLUX/ DOMETIC refrigerators with "AES" (Automatic Energy Selector) to switch automatically from gas to 12 V operation when there is plenty of excess solar power.Connection for temperature sensor (art. no. 2001): Automatic adjustment of the charging voltage to the battery temperature. Improves full charging of the weaker battery in cold weather and prevents unnecessary battery gassing in summer temperatures. Highly recommended if the battery is exposed to strong temperature fluctuations, e.g. in the engine compartment.Ready to plug in for connecting the Votronic solar display units for optimum control of the system: LCD Solar Computer S: LCD display with display range: battery voltage, charging current, charging power, stored capacity and energy (V, A, W, Ah, Wh).with electronics protected against moistureAmbient conditions, humidity: max. 95% room humidity, non-condensing Scope of delivery: Operating instructions

€206.98*

Votronic 1720 MPP 350 Duo Digital 21A 12V MPPT solar charge controller for two batteries

MPP solar controller specially designed for use on boats, yachts, etc. The electronics of the MPPT dual charge controller are protected against moisture. For solar modules with:up to 350 Wp module outputmax. 21 A module currentmax. 50 V module voltageCharging options: 1 supply battery and 1 starter battery Votronic solar controllers of the "MPP" (Maximum Power Point) series with "IU1oU2" charging characteristic are connected as a link between the solar panel(s) and battery(ies). With MPP technology, the controller automatically determines the maximum power output (MPP) of the solar modules several times per second. It then transforms the excess voltage of the solar module into a higher charging current for the battery (realized by high-frequency switching regulator technology with high efficiency). This additional charging current ensures shorter charging times and the best possible power utilization of the solar system.MPP solar controllers work fully automatically, are maintenance-free and offer the following functions: MPP charging current increase of 10 % to 30 % (efficiency > 95 %) compared to conventional controllers thanks to the use of state-of-the-art controller technology (microprocessor). The increase in performance is particularly noticeable at cooler times of the year and e.g. during high fog conditions, low and diffuse lighting (wintering).Switchable charging characteristics for optimum charging of gel/dryfit, AGM/non-woven or acid/wet and LiFePO4 batteries (see Table 1).The charging voltage is free of peaks and regulated in such a way that overcharging of batteries is ruled out.Two battery charging outputs:Automatic charging of the main or on-board battery (Board I).Support charging and charge retention (max. 1 A) of the vehicle starter battery (Start II) with protection against overcharging.Monitoring-free charging:Standard protection against overload, overheating, reverse polarity and reverse battery discharge (if solar power is too low, e.g. at dusk, at night, etc.).Parallel/buffer operation:Maintains charging characteristics even when loads are operated simultaneously.Overcharge protection: Regulates the charging current of the battery back if there is too much solar power and the battery is full, ensures that the battery is charged to the highest possible level by immediately recharging when power is consumed."IU1oU2" charging characteristic: Defined charging voltage increase (U1) prevents harmful acid stratification and ensures equalization charging of the individual battery cells, followed by automatic trickle charging (U2).Charging cable compensation: Voltage losses on the charging cables are automatically compensated for.On-board power supply filter: Problem-free parallel operation with wind and petrol generators, mains chargers, alternators, etc.Measurement output for EBL (electric block of the vehicle): Enables convenient use of the (solar) current display built into the electrical block to check the solar system.Switching output "AES" (only MPP250 Duo Dig. and MPP350 Duo Dig): Causes the ELECTROLUX/ DOMETIC refrigerators with "AES" (Automatic Energy Selector) to switch automatically from gas to 12 V operation when there is plenty of excess solar power.Connection for temperature sensor (art. no. 2001): Automatic adjustment of the charging voltage to the battery temperature. Improves full charging of the weaker battery in cold weather and prevents unnecessary battery gassing in summer temperatures. Highly recommended if the battery is exposed to strong temperature fluctuations, e.g. in the engine compartment.Ready to plug in for connecting the Votronic solar display units for optimum control of the system: LCD Solar Computer S: LCD display with display range: battery voltage, charging current, charging power, stored capacity and energy (V, A, W, Ah, Wh).with electronics protected against moistureAmbient conditions, humidity: max. 95% room humidity, non-condensing Scope of delivery: Operating instructions

€206.98*

Votronic 1715 MPP 250 Duo Digital 15A 12V MPPT solar charge controller for two batteries (VAT Exempt)

MPP solar controller specially designed for use on boats, yachts, etc. The electronics of the MPPT dual charge controller are protected against moisture. For solar modules with: up to 250 Wp module output max. 15 A module current max. 50 V module voltage Charging options: 1 supply battery and 1 starter battery Votronic solar controllers of the "MPP" (Maximum Power Point) series with "IU1oU2" charging characteristic are connected as a link between the solar panel(s) and battery(ies). With MPP technology, the controller automatically determines the maximum power output (MPP) of the solar modules several times per second. It then transforms the excess voltage of the solar module into a higher charging current for the battery (realized by high-frequency switching regulator technology with high efficiency). This additional charging current ensures shorter charging times and the best possible power utilization of the solar system.MPP solar controllers work fully automatically, are maintenance-free and offer the following functions: MPP charging current increase of 10 % to 30 % (efficiency > 95 %) compared to conventional controllers thanks to the use of state-of-the-art controller technology (microprocessor). The increase in performance is particularly noticeable at cooler times of the year and e.g. during high fog conditions, low and diffuse lighting (wintering). Switchable charging characteristics for optimum charging of gel/dryfit, AGM/non-woven or acid/wet and LiFePO4 batteries (see Table 1). The charging voltage is free of peaks and regulated in such a way that overcharging of batteries is ruled out. Two battery charging outputs:Automatic charging of the main or on-board battery (Board I).Support charging and charge retention (max. 1 A) of the vehicle starter battery (Start II) with protection against overcharging. Monitoring-free charging:Standard protection against overload, overheating, reverse polarity and reverse battery discharge (if solar power is too low, e.g. at dusk, at night, etc.). Parallel/buffer operation:Maintains charging characteristics even when loads are operated simultaneously. Overcharge protection: Regulates the charging current of the battery back if there is too much solar power and the battery is full, ensures that the battery is charged to the highest possible level by immediately recharging when power is consumed. "IU1oU2" charging characteristic: Defined charging voltage increase (U1) prevents harmful acid stratification and ensures equalization charging of the individual battery cells, followed by automatic trickle charging (U2). Charging cable compensation: Voltage losses on the charging cables are automatically compensated for. On-board power supply filter: Problem-free parallel operation with wind and petrol generators, mains chargers, alternators, etc. Measurement output for EBL (electric block of the vehicle): Enables convenient use of the (solar) current display built into the electrical block to check the solar system. Switching output "AES" (only MPP250 Duo Dig. and MPP350 Duo Dig): Causes the ELECTROLUX/ DOMETIC refrigerators with "AES" (Automatic Energy Selector) to switch automatically from gas to 12 V operation when there is plenty of excess solar power. Connection for temperature sensor (art. no. 2001): Automatic adjustment of the charging voltage to the battery temperature. Improves full charging of the weaker battery in cold weather and prevents unnecessary battery gassing in summer temperatures. Highly recommended if the battery is exposed to strong temperature fluctuations, e.g. in the engine compartment. Ready to plug in for connecting the Votronic solar display units for optimum control of the system: LCD Solar Computer S: LCD display with display range: battery voltage, charging current, charging power, stored capacity and energy (V, A, W, Ah, Wh). Ambient conditions, humidity: max. 95% room humidity, non-condensingScope of delivery: Operating instructions

€142.90*

Votronic 1715 MPP 250 Duo Digital 15A 12V MPPT solar charge controller for two batteries

MPP solar controller specially designed for use on boats, yachts, etc. The electronics of the MPPT dual charge controller are protected against moisture. For solar modules with: up to 250 Wp module output max. 15 A module current max. 50 V module voltage Charging options: 1 supply battery and 1 starter battery Votronic solar controllers of the "MPP" (Maximum Power Point) series with "IU1oU2" charging characteristic are connected as a link between the solar panel(s) and battery(ies). With MPP technology, the controller automatically determines the maximum power output (MPP) of the solar modules several times per second. It then transforms the excess voltage of the solar module into a higher charging current for the battery (realized by high-frequency switching regulator technology with high efficiency). This additional charging current ensures shorter charging times and the best possible power utilization of the solar system.MPP solar controllers work fully automatically, are maintenance-free and offer the following functions: MPP charging current increase of 10 % to 30 % (efficiency > 95 %) compared to conventional controllers thanks to the use of state-of-the-art controller technology (microprocessor). The increase in performance is particularly noticeable at cooler times of the year and e.g. during high fog conditions, low and diffuse lighting (wintering). Switchable charging characteristics for optimum charging of gel/dryfit, AGM/non-woven or acid/wet and LiFePO4 batteries (see Table 1). The charging voltage is free of peaks and regulated in such a way that overcharging of batteries is ruled out. Two battery charging outputs:Automatic charging of the main or on-board battery (Board I).Support charging and charge retention (max. 1 A) of the vehicle starter battery (Start II) with protection against overcharging. Monitoring-free charging:Standard protection against overload, overheating, reverse polarity and reverse battery discharge (if solar power is too low, e.g. at dusk, at night, etc.). Parallel/buffer operation:Maintains charging characteristics even when loads are operated simultaneously. Overcharge protection: Regulates the charging current of the battery back if there is too much solar power and the battery is full, ensures that the battery is charged to the highest possible level by immediately recharging when power is consumed. "IU1oU2" charging characteristic: Defined charging voltage increase (U1) prevents harmful acid stratification and ensures equalization charging of the individual battery cells, followed by automatic trickle charging (U2). Charging cable compensation: Voltage losses on the charging cables are automatically compensated for. On-board power supply filter: Problem-free parallel operation with wind and petrol generators, mains chargers, alternators, etc. Measurement output for EBL (electric block of the vehicle): Enables convenient use of the (solar) current display built into the electrical block to check the solar system. Switching output "AES" (only MPP250 Duo Dig. and MPP350 Duo Dig): Causes the ELECTROLUX/ DOMETIC refrigerators with "AES" (Automatic Energy Selector) to switch automatically from gas to 12 V operation when there is plenty of excess solar power. Connection for temperature sensor (art. no. 2001): Automatic adjustment of the charging voltage to the battery temperature. Improves full charging of the weaker battery in cold weather and prevents unnecessary battery gassing in summer temperatures. Highly recommended if the battery is exposed to strong temperature fluctuations, e.g. in the engine compartment. Ready to plug in for connecting the Votronic solar display units for optimum control of the system: LCD Solar Computer S: LCD display with display range: battery voltage, charging current, charging power, stored capacity and energy (V, A, W, Ah, Wh). Ambient conditions, humidity: max. 95% room humidity, non-condensingScope of delivery: Operating instructions

€149.00*

Votronic 11725 MPP 430 Duo Digital (Marine Version) 26A MPPT Dual Solar Charge Controller 12V

MPP solar controller for high-quality motorhomes, caravans and boats. For solar modules with:- up to 430 Wp module output- max. 26 A module current- max. 50 V module voltage Charging options: 1 supply battery and 1 starter battery Votronic solar controllers of the "MPP" (Maximum Power Point) series with "IU1oU2" charging characteristic are connected as a link between the solar panel(s) and battery(ies). With MPP technology, the controller automatically determines the maximum power output (MPP) of the solar modules several times per second. It then transforms the excess voltage of the solar module into a higher charging current for the battery (realized by high-frequency switching regulator technology with high efficiency). This additional charging current ensures shorter charging times and the best possible power utilization of the solar system. MPP solar controllers work fully automatically, are maintenance-free and offer the following functions: - MPP charging current increase of 10 % to 30 % (efficiency > 95 %) compared to conventional controllers through the use of the latest controller technology (microprocessor). The increase in performance is particularly noticeable in the cooler months of the year and e.g. during high fog conditions, low and diffuse lighting (wintering).- Switchable charging characteristics for optimum charging of gel/dryfit, AGM/non-woven or acid/wet and LiFePO4 batteries (see Table 1).- The charging voltage is free of peaks and regulated in such a way that overcharging of the batteries is impossible.- Two battery charging outputs: Automatic charging of the main or on-board battery (Board I), support charging and charge retention (max. 1 A) of the vehicle starter battery (Start II) with protection against overcharging.- Monitoring-free charging: Standard protection against overload, overheating, reverse polarity and reverse battery discharge (if solar power is too low, e.g. at dusk, at night, etc.).- Parallel/buffer operation: Charging characteristics are maintained even with simultaneous operation of consumers.- Overcharge protection: Reduces the charging current of the battery if there is too much solar power and the battery is full, ensures that the battery is charged to the highest possible level by immediately recharging when power is consumed.- "IU1oU2" charging characteristic: Defined charging voltage increase (U1) prevents harmful acid stratification and ensures equalization charging of the individual battery cells, followed by automatic trickle charging (U2).- Charging cable compensation: Voltage losses on the charging cables are automatically compensated for.- On-board power supply filter: Problem-free parallel operation with wind and gasoline generators, mains chargers, alternators, etc.- Connection for external battery temperature sensor Automatic adjustment of the charging voltage to the battery temperature. Improves full charging of the weaker battery in cold weather, avoids unnecessary battery gassing in summer temperatures; increases battery service life. Highly recommended if the battery is exposed to strong temperature fluctuations, e.g. in the engine compartment.- Ready to plug in for connecting the VOTRONIC Solar display units for optimum control of the system Ambient conditions, humidity: max. 95% room humidity, non-condensing Scope of delivery: Operating instructions, charge controller Mpp 420 (Votronic 13039)

€233.14*

Votronic 1440 Solar Data Extender 3n1

The Solar Data Extender combines the data from up to three solar controllers so that they can be shown on a single display. The familiar LCD display can still be used. It is compatible with the following devices: Solar charge controllers in SR and MPP technology (from serial no. 14Vxx.xxxxx) Battery Charger type VBCS Triple LCD Solar Computer S (from serial no. 15V40.xxxxx) LCD Charge Control S VPC series with solar function Bluetooth Connector S-BC Installation and connection The Solar Data Extender can be retrofitted at any time. It has three independent inputs (IN1, IN2, IN3). The signals are combined and made available via the output (OUT). A solar display (e.g. LCD Solar Computer S) can be connected there. It is connected between the Votronic solar charge controller and the solar display (e.g. LCD Solar Computer S) using the modular cable included in the scope of delivery. The IN1 connection must always be connected, as this is used to supply power to the device. Technical data Data Extender 3 in 1 Nominal voltage (supply via connected devices) 12 and 24 Operating voltage range [V] 8 - 32 Current consumption in standby, typical [mA] 0.7 Current consumption during activity, typical [mA} 10 Dimensions (WxHxD) in [mm] 75 x 47 x 24 Weight in [g] 37 Test mark CE, E-test (EMC/vehicle directive) Ambient conditions, humidity: max. 95% room humidity, non-condensing Scope of delivery: 3 pcs. control cable 6-pin 0.5 m long, operating instructions

€76.39*

Votronic 1710 MPP 165 Duo Digital 10A 12V MPPT solar charge controller for two batteries

MPP solar controller specially designed for use on boats, yachts etc. The electronics of the MPPT dual charge controller are protected against moisture. For solar modules with: up to 165 Wp module outputmax. 10 A module currentmax. 50 V module voltageCharging options: 1 supply battery and 1 starter battery Votronic solar controllers of the "MPP" (Maximum Power Point) series with "IU1oU2" charging characteristic are connected as a link between the solar panel(s) and battery(ies). With MPP technology, the controller automatically determines the maximum power output (MPP) of the solar modules several times per second. It then transforms the excess voltage of the solar module into a higher charging current for the battery (realized by high-frequency switching regulator technology with high efficiency). This additional charging current ensures shorter charging times and the best possible power utilization of the solar system.MPP solar controllers work fully automatically, are maintenance-free and offer the following functions: MPP charging current increase of 10 % to 30 % (efficiency > 95 %) compared to conventional controllers thanks to the use of state-of-the-art controller technology (microprocessor). The increase in performance is particularly noticeable at cooler times of the year and e.g. during high fog conditions, low and diffuse lighting (wintering).Switchable charging characteristics for optimum charging of gel/dryfit, AGM/non-woven or acid/wet and LiFePO4 batteries (see Table 1).The charging voltage is free of peaks and regulated in such a way that overcharging of batteries is excluded.Two battery charging outputs:Automatic charging of the main or on-board battery (Board I).Support charging and charge retention (max. 1 A) of the vehicle starter battery (Start II) with protection against overcharging.Monitoring-free charging:Standard protection against overload, overheating, reverse polarity and reverse battery discharge (if solar power is too low, e.g. at dusk, at night, etc.).Parallel/buffer operation:Maintains charging characteristics even when loads are operated simultaneously.Overcharge protection: Regulates the charging current of the battery back if there is too much solar power and the battery is full, ensures that the battery is charged to the highest possible level by immediately recharging when power is consumed."IU1oU2" charging characteristic: Defined charging voltage increase (U1) prevents harmful acid stratification and ensures equalization charging of the individual battery cells, followed by automatic trickle charging (U2).Charging cable compensation: Voltage losses on the charging cables are automatically compensated for.On-board power supply filter: Problem-free parallel operation with wind and petrol generators, mains chargers, alternators, etc.Measurement output for EBL (electric block of the vehicle): Enables convenient use of the (solar) current display built into the electrical block to check the solar system.Switching output "AES" (only MPP250 Duo Dig. and MPP350 Duo Dig): Causes the ELECTROLUX/ DOMETIC refrigerators with "AES" (Automatic Energy Selector) to switch automatically from gas to 12 V operation when there is plenty of excess solar power.Connection for temperature sensor (art. no. 2001): Automatic adjustment of the charging voltage to the battery temperature. Improves full charging of the weaker battery in cold weather and prevents unnecessary battery gassing in summer temperatures. Highly recommended if the battery is exposed to strong temperature fluctuations, e.g. in the engine compartment.Ready to plug in for connecting the Votronic solar display units for optimum control of the system: LCD Solar Computer S: LCD display with display range: battery voltage, charging current, charging power, stored capacity and energy (V, A, W, Ah, Wh).Electronics protected from moistureAmbient conditions, humidity: max. 95% room humidity, non-condensing Scope of delivery: Operating instructions

€87.00*

Votronic 1710 MPP 165 Duo Digital 10A 12V MPPT solar charge controller for two batteries

MPP solar controller specially designed for use on boats, yachts etc. The electronics of the MPPT dual charge controller are protected against moisture. For solar modules with: up to 165 Wp module outputmax. 10 A module currentmax. 50 V module voltageCharging options: 1 supply battery and 1 starter battery Votronic solar controllers of the "MPP" (Maximum Power Point) series with "IU1oU2" charging characteristic are connected as a link between the solar panel(s) and battery(ies). With MPP technology, the controller automatically determines the maximum power output (MPP) of the solar modules several times per second. It then transforms the excess voltage of the solar module into a higher charging current for the battery (realized by high-frequency switching regulator technology with high efficiency). This additional charging current ensures shorter charging times and the best possible power utilization of the solar system.MPP solar controllers work fully automatically, are maintenance-free and offer the following functions: MPP charging current increase of 10 % to 30 % (efficiency > 95 %) compared to conventional controllers thanks to the use of state-of-the-art controller technology (microprocessor). The increase in performance is particularly noticeable at cooler times of the year and e.g. during high fog conditions, low and diffuse lighting (wintering).Switchable charging characteristics for optimum charging of gel/dryfit, AGM/non-woven or acid/wet and LiFePO4 batteries (see Table 1).The charging voltage is free of peaks and regulated in such a way that overcharging of batteries is excluded.Two battery charging outputs:Automatic charging of the main or on-board battery (Board I).Support charging and charge retention (max. 1 A) of the vehicle starter battery (Start II) with protection against overcharging.Monitoring-free charging:Standard protection against overload, overheating, reverse polarity and reverse battery discharge (if solar power is too low, e.g. at dusk, at night, etc.).Parallel/buffer operation:Maintains charging characteristics even when loads are operated simultaneously.Overcharge protection: Regulates the charging current of the battery back if there is too much solar power and the battery is full, ensures that the battery is charged to the highest possible level by immediately recharging when power is consumed."IU1oU2" charging characteristic: Defined charging voltage increase (U1) prevents harmful acid stratification and ensures equalization charging of the individual battery cells, followed by automatic trickle charging (U2).Charging cable compensation: Voltage losses on the charging cables are automatically compensated for.On-board power supply filter: Problem-free parallel operation with wind and petrol generators, mains chargers, alternators, etc.Measurement output for EBL (electric block of the vehicle): Enables convenient use of the (solar) current display built into the electrical block to check the solar system.Switching output "AES" (only MPP250 Duo Dig. and MPP350 Duo Dig): Causes the ELECTROLUX/ DOMETIC refrigerators with "AES" (Automatic Energy Selector) to switch automatically from gas to 12 V operation when there is plenty of excess solar power.Connection for temperature sensor (art. no. 2001): Automatic adjustment of the charging voltage to the battery temperature. Improves full charging of the weaker battery in cold weather and prevents unnecessary battery gassing in summer temperatures. Highly recommended if the battery is exposed to strong temperature fluctuations, e.g. in the engine compartment.Ready to plug in for connecting the Votronic solar display units for optimum control of the system: LCD Solar Computer S: LCD display with display range: battery voltage, charging current, charging power, stored capacity and energy (V, A, W, Ah, Wh).Electronics protected from moistureAmbient conditions, humidity: max. 95% room humidity, non-condensing Scope of delivery: Operating instructions

€104.53*

Votronic 11715 MPP 250 Duo Digital (Marine Version) 15A MPPT Dual Solar Charge Controller 12V

MPP solar controller specially designed for use on boats, yachts, etc. The electronics of the MPPT dual charge controller are protected against moisture. For solar modules with: up to 250 Wp module output max. 15 A module current max. 50 V module voltage Charging options: 1 supply battery and 1 starter battery Votronic solar controllers of the "MPP" (Maximum Power Point) series with "IU1oU2" charging characteristic are connected as a link between the solar panel(s) and battery(ies). With MPP technology, the controller automatically determines the maximum power output (MPP) of the solar modules several times per second. It then transforms the excess voltage of the solar module into a higher charging current for the battery (realized by high-frequency switching regulator technology with high efficiency). This additional charging current ensures shorter charging times and the best possible power utilization of the solar system.MPP solar controllers work fully automatically, are maintenance-free and offer the following functions: MPP charging current increase of 10 % to 30 % (efficiency > 95 %) compared to conventional controllers thanks to the use of state-of-the-art controller technology (microprocessor). The increase in performance is particularly noticeable at cooler times of the year and e.g. during high fog conditions, low and diffuse lighting (wintering). Switchable charging characteristics for optimum charging of gel/dryfit, AGM/non-woven or acid/wet and LiFePO4 batteries (see Table 1). The charging voltage is free of peaks and regulated in such a way that overcharging of batteries is ruled out. Two battery charging outputs:Automatic charging of the main or on-board battery (Board I).Support charging and charge retention (max. 1 A) of the vehicle starter battery (Start II) with protection against overcharging. Monitoring-free charging:Standard protection against overload, overheating, reverse polarity and reverse battery discharge (if solar power is too low, e.g. at dusk, at night, etc.). Parallel/buffer operation:Maintains charging characteristics even when loads are operated simultaneously. Overcharge protection: Regulates the charging current of the battery back if there is too much solar power and the battery is full, ensures that the battery is charged to the highest possible level by immediately recharging when power is consumed. "IU1oU2" charging characteristic: Defined charging voltage increase (U1) prevents harmful acid stratification and ensures equalization charging of the individual battery cells, followed by automatic trickle charging (U2). Charging cable compensation: Voltage losses on the charging cables are automatically compensated for. On-board power supply filter: Problem-free parallel operation with wind and petrol generators, mains chargers, alternators, etc. Measurement output for EBL (electric block of the vehicle): Enables convenient use of the (solar) current display built into the electrical block to check the solar system. Switching output "AES" (only MPP250 Duo Dig. and MPP350 Duo Dig): Causes the ELECTROLUX/ DOMETIC refrigerators with "AES" (Automatic Energy Selector) to switch automatically from gas to 12 V operation when there is plenty of excess solar power. Connection for temperature sensor (art. no. 2001): Automatic adjustment of the charging voltage to the battery temperature. Improves full charging of the weaker battery in cold weather and prevents unnecessary battery gassing in summer temperatures. Highly recommended if the battery is exposed to strong temperature fluctuations, e.g. in the engine compartment. Ready to plug in for connecting the Votronic solar display units for optimum control of the system: LCD Solar Computer S: LCD display with display range: battery voltage, charging current, charging power, stored capacity and energy (V, A, W, Ah, Wh). Ambient conditions, humidity: max. 95% room humidity, non-condensingScope of delivery: Operating instructions

€125.46*

Votronic 11715 MPP 250 Duo Digital (Marine Version) 15A MPPT Dual Solar Charge Controller 12V

MPP solar controller specially designed for use on boats, yachts, etc. The electronics of the MPPT dual charge controller are protected against moisture. For solar modules with: up to 250 Wp module output max. 15 A module current max. 50 V module voltage Charging options: 1 supply battery and 1 starter battery Votronic solar controllers of the "MPP" (Maximum Power Point) series with "IU1oU2" charging characteristic are connected as a link between the solar panel(s) and battery(ies). With MPP technology, the controller automatically determines the maximum power output (MPP) of the solar modules several times per second. It then transforms the excess voltage of the solar module into a higher charging current for the battery (realized by high-frequency switching regulator technology with high efficiency). This additional charging current ensures shorter charging times and the best possible power utilization of the solar system.MPP solar controllers work fully automatically, are maintenance-free and offer the following functions: MPP charging current increase of 10 % to 30 % (efficiency > 95 %) compared to conventional controllers thanks to the use of state-of-the-art controller technology (microprocessor). The increase in performance is particularly noticeable at cooler times of the year and e.g. during high fog conditions, low and diffuse lighting (wintering). Switchable charging characteristics for optimum charging of gel/dryfit, AGM/non-woven or acid/wet and LiFePO4 batteries (see Table 1). The charging voltage is free of peaks and regulated in such a way that overcharging of batteries is ruled out. Two battery charging outputs:Automatic charging of the main or on-board battery (Board I).Support charging and charge retention (max. 1 A) of the vehicle starter battery (Start II) with protection against overcharging. Monitoring-free charging:Standard protection against overload, overheating, reverse polarity and reverse battery discharge (if solar power is too low, e.g. at dusk, at night, etc.). Parallel/buffer operation:Maintains charging characteristics even when loads are operated simultaneously. Overcharge protection: Regulates the charging current of the battery back if there is too much solar power and the battery is full, ensures that the battery is charged to the highest possible level by immediately recharging when power is consumed. "IU1oU2" charging characteristic: Defined charging voltage increase (U1) prevents harmful acid stratification and ensures equalization charging of the individual battery cells, followed by automatic trickle charging (U2). Charging cable compensation: Voltage losses on the charging cables are automatically compensated for. On-board power supply filter: Problem-free parallel operation with wind and petrol generators, mains chargers, alternators, etc. Measurement output for EBL (electric block of the vehicle): Enables convenient use of the (solar) current display built into the electrical block to check the solar system. Switching output "AES" (only MPP250 Duo Dig. and MPP350 Duo Dig): Causes the ELECTROLUX/ DOMETIC refrigerators with "AES" (Automatic Energy Selector) to switch automatically from gas to 12 V operation when there is plenty of excess solar power. Connection for temperature sensor (art. no. 2001): Automatic adjustment of the charging voltage to the battery temperature. Improves full charging of the weaker battery in cold weather and prevents unnecessary battery gassing in summer temperatures. Highly recommended if the battery is exposed to strong temperature fluctuations, e.g. in the engine compartment. Ready to plug in for connecting the Votronic solar display units for optimum control of the system: LCD Solar Computer S: LCD display with display range: battery voltage, charging current, charging power, stored capacity and energy (V, A, W, Ah, Wh). Ambient conditions, humidity: max. 95% room humidity, non-condensingScope of delivery: Operating instructions

€142.90*

Details

Votronic 11720 MPP 350 Duo Digital (Marine Version) 21A MPPT Dual Solar Charge Controller 12V (VAT Exempt)

MPP solar controller specially designed for use on boats, yachts, etc. The electronics of the MPPT dual charge controller are protected against moisture. For solar modules with:up to 350 Wp module outputmax. 21 A module currentmax. 50 V module voltageCharging options: 1 supply battery and 1 starter battery Votronic solar controllers of the "MPP" (Maximum Power Point) series with "IU1oU2" charging characteristic are connected as a link between the solar panel(s) and battery(ies). With MPP technology, the controller automatically determines the maximum power output (MPP) of the solar modules several times per second. It then transforms the excess voltage of the solar module into a higher charging current for the battery (realized by high-frequency switching regulator technology with high efficiency). This additional charging current ensures shorter charging times and the best possible power utilization of the solar system.MPP solar controllers work fully automatically, are maintenance-free and offer the following functions: MPP charging current increase of 10 % to 30 % (efficiency > 95 %) compared to conventional controllers thanks to the use of state-of-the-art controller technology (microprocessor). The increase in performance is particularly noticeable at cooler times of the year and e.g. during high fog conditions, low and diffuse lighting (wintering).Switchable charging characteristics for optimum charging of gel/dryfit, AGM/non-woven or acid/wet and LiFePO4 batteries (see Table 1).The charging voltage is free of peaks and regulated in such a way that overcharging of batteries is excluded.Two battery charging outputs:Automatic charging of the main or on-board battery (Board I).Support charging and charge retention (max. 1 A) of the vehicle starter battery (Start II) with protection against overcharging.Monitoring-free charging:Standard protection against overload, overheating, reverse polarity and reverse battery discharge (if solar power is too low, e.g. at dusk, at night, etc.).Parallel/buffer operation:Maintains charging characteristics even when loads are operated simultaneously.Overcharge protection: Regulates the charging current of the battery back if there is too much solar power and the battery is full, ensures that the battery is charged to the highest possible level by immediately recharging when power is consumed."IU1oU2" charging characteristic: Defined charging voltage increase (U1) prevents harmful acid stratification and ensures equalization charging of the individual battery cells, followed by automatic trickle charging (U2).Charging cable compensation: Voltage losses on the charging cables are automatically compensated for.On-board power supply filter: Problem-free parallel operation with wind and petrol generators, mains chargers, alternators, etc.Measurement output for EBL (electric block of the vehicle): Enables convenient use of the (solar) current display built into the electrical block to check the solar system.Switching output "AES" (only MPP250 Duo Dig. and MPP350 Duo Dig): Causes the ELECTROLUX/ DOMETIC refrigerators with "AES" (Automatic Energy Selector) to switch automatically from gas to 12 V operation when there is plenty of excess solar power.Connection for temperature sensor (art. no. 2001): Automatic adjustment of the charging voltage to the battery temperature. Improves full charging of the weaker battery in cold weather and prevents unnecessary battery gassing in summer temperatures. Highly recommended if the battery is exposed to strong temperature fluctuations, e.g. in the engine compartment.Ready to plug in for connecting the Votronic solar display units for optimum control of the system: LCD Solar Computer S: LCD display with display range: battery voltage, charging current, charging power, stored capacity and energy (V, A, W, Ah, Wh).with electronics protected against moistureAmbient conditions, humidity: max. 95% room humidity, non-condensing Scope of delivery: Operating instructions

€289.26*

Votronic 11725 MPP 430 Duo Digital (Marine Version) 26A MPPT Dual Solar Charge Controller 12V

MPP solar controller for high-quality motorhomes, caravans and boats. For solar modules with:- up to 430 Wp module output- max. 26 A module current- max. 50 V module voltage Charging options: 1 supply battery and 1 starter battery Votronic solar controllers of the "MPP" (Maximum Power Point) series with "IU1oU2" charging characteristic are connected as a link between the solar panel(s) and battery(ies). With MPP technology, the controller automatically determines the maximum power output (MPP) of the solar modules several times per second. It then transforms the excess voltage of the solar module into a higher charging current for the battery (realized by high-frequency switching regulator technology with high efficiency). This additional charging current ensures shorter charging times and the best possible power utilization of the solar system. MPP solar controllers work fully automatically, are maintenance-free and offer the following functions: - MPP charging current increase of 10 % to 30 % (efficiency > 95 %) compared to conventional controllers through the use of the latest controller technology (microprocessor). The increase in performance is particularly noticeable in the cooler months of the year and e.g. during high fog conditions, low and diffuse lighting (wintering).- Switchable charging characteristics for optimum charging of gel/dryfit, AGM/non-woven or acid/wet and LiFePO4 batteries (see Table 1).- The charging voltage is free of peaks and regulated in such a way that overcharging of the batteries is impossible.- Two battery charging outputs: Automatic charging of the main or on-board battery (Board I), support charging and charge retention (max. 1 A) of the vehicle starter battery (Start II) with protection against overcharging.- Monitoring-free charging: Standard protection against overload, overheating, reverse polarity and reverse battery discharge (if solar power is too low, e.g. at dusk, at night, etc.).- Parallel/buffer operation: Charging characteristics are maintained even with simultaneous operation of consumers.- Overcharge protection: Reduces the charging current of the battery if there is too much solar power and the battery is full, ensures that the battery is charged to the highest possible level by immediately recharging when power is consumed.- "IU1oU2" charging characteristic: Defined charging voltage increase (U1) prevents harmful acid stratification and ensures equalization charging of the individual battery cells, followed by automatic trickle charging (U2).- Charging cable compensation: Voltage losses on the charging cables are automatically compensated for.- On-board power supply filter: Problem-free parallel operation with wind and gasoline generators, mains chargers, alternators, etc.- Connection for external battery temperature sensor Automatic adjustment of the charging voltage to the battery temperature. Improves full charging of the weaker battery in cold weather, avoids unnecessary battery gassing in summer temperatures; increases battery service life. Highly recommended if the battery is exposed to strong temperature fluctuations, e.g. in the engine compartment.- Ready to plug in for connecting the VOTRONIC Solar display units for optimum control of the system Ambient conditions, humidity: max. 95% room humidity, non-condensing Scope of delivery: Operating instructions, charge controller Mpp 420 (Votronic 13039)

€233.14*

Votronic 11710 MPP 165 Duo Digital (Marine Version) 10A MPPT Dual Solar Charge Controller 12V

MPP solar controller specially designed for use on boats, yachts etc. The electronics of the MPPT dual charge controller are protected against moisture. For solar modules with: up to 165 Wp module outputmax. 10 A module currentmax. 50 V module voltageCharging options: 1 supply battery and 1 starter battery Votronic solar controllers of the "MPP" (Maximum Power Point) series with "IU1oU2" charging characteristic are connected as a link between the solar panel(s) and battery(ies). With MPP technology, the controller automatically determines the maximum power output (MPP) of the solar modules several times per second. It then transforms the excess voltage of the solar module into a higher charging current for the battery (realized by high-frequency switching regulator technology with high efficiency). This additional charging current ensures shorter charging times and the best possible power utilization of the solar system.MPP solar controllers work fully automatically, are maintenance-free and offer the following functions: MPP charging current increase of 10 % to 30 % (efficiency > 95 %) compared to conventional controllers thanks to the use of state-of-the-art controller technology (microprocessor). The increase in performance is particularly noticeable at cooler times of the year and e.g. during high fog conditions, low and diffuse lighting (wintering).Switchable charging characteristics for optimum charging of gel/dryfit, AGM/non-woven or acid/wet and LiFePO4 batteries (see Table 1).The charging voltage is free of peaks and regulated in such a way that overcharging of batteries is ruled out.Two battery charging outputs:Automatic charging of the main or on-board battery (Board I).Support charging and charge retention (max. 1 A) of the vehicle starter battery (Start II) with protection against overcharging.Monitoring-free charging:Standard protection against overload, overheating, reverse polarity and reverse battery discharge (if solar power is too low, e.g. at dusk, at night, etc.).Parallel/buffer operation:Maintains charging characteristics even when loads are operated simultaneously.Overcharge protection: Regulates the charging current of the battery back if there is too much solar power and the battery is full, ensures that the battery is charged to the highest possible level by immediately recharging when power is consumed."IU1oU2" charging characteristic: Defined charging voltage increase (U1) prevents harmful acid stratification and ensures equalization charging of the individual battery cells, followed by automatic trickle charging (U2).Charging cable compensation: Voltage losses on the charging cables are automatically compensated for.On-board power supply filter: Problem-free parallel operation with wind and petrol generators, mains chargers, alternators, etc.Measurement output for EBL (electric block of the vehicle): Enables convenient use of the (solar) current display built into the electrical block to check the solar system.Switching output "AES" (only MPP250 Duo Dig. and MPP350 Duo Dig): Causes the ELECTROLUX/ DOMETIC refrigerators with "AES" (Automatic Energy Selector) to switch automatically from gas to 12 V operation when there is plenty of excess solar power.Connection for temperature sensor (art. no. 2001): Automatic adjustment of the charging voltage to the battery temperature. Improves full charging of the weaker battery in cold weather and prevents unnecessary battery gassing in summer temperatures. Highly recommended if the battery is exposed to strong temperature fluctuations, e.g. in the engine compartment.Ready to plug in for connecting the Votronic solar display units for optimum control of the system: LCD Solar Computer S: LCD display with display range: battery voltage, charging current, charging power, stored capacity and energy (V, A, W, Ah, Wh).Electronics protected from moistureAmbient conditions, humidity: max. 95% room humidity, non-condensing Scope of delivery: Operating instructions

€108.52*

Votronic 11710 MPP 165 Duo Digital (Marine Version) 10A MPPT Dual Solar Charge Controller 12V

MPP solar controller specially designed for use on boats, yachts etc. The electronics of the MPPT dual charge controller are protected against moisture. For solar modules with: up to 165 Wp module outputmax. 10 A module currentmax. 50 V module voltageCharging options: 1 supply battery and 1 starter battery Votronic solar controllers of the "MPP" (Maximum Power Point) series with "IU1oU2" charging characteristic are connected as a link between the solar panel(s) and battery(ies). With MPP technology, the controller automatically determines the maximum power output (MPP) of the solar modules several times per second. It then transforms the excess voltage of the solar module into a higher charging current for the battery (realized by high-frequency switching regulator technology with high efficiency). This additional charging current ensures shorter charging times and the best possible power utilization of the solar system.MPP solar controllers work fully automatically, are maintenance-free and offer the following functions: MPP charging current increase of 10 % to 30 % (efficiency > 95 %) compared to conventional controllers thanks to the use of state-of-the-art controller technology (microprocessor). The increase in performance is particularly noticeable at cooler times of the year and e.g. during high fog conditions, low and diffuse lighting (wintering).Switchable charging characteristics for optimum charging of gel/dryfit, AGM/non-woven or acid/wet and LiFePO4 batteries (see Table 1).The charging voltage is free of peaks and regulated in such a way that overcharging of batteries is ruled out.Two battery charging outputs:Automatic charging of the main or on-board battery (Board I).Support charging and charge retention (max. 1 A) of the vehicle starter battery (Start II) with protection against overcharging.Monitoring-free charging:Standard protection against overload, overheating, reverse polarity and reverse battery discharge (if solar power is too low, e.g. at dusk, at night, etc.).Parallel/buffer operation:Maintains charging characteristics even when loads are operated simultaneously.Overcharge protection: Regulates the charging current of the battery back if there is too much solar power and the battery is full, ensures that the battery is charged to the highest possible level by immediately recharging when power is consumed."IU1oU2" charging characteristic: Defined charging voltage increase (U1) prevents harmful acid stratification and ensures equalization charging of the individual battery cells, followed by automatic trickle charging (U2).Charging cable compensation: Voltage losses on the charging cables are automatically compensated for.On-board power supply filter: Problem-free parallel operation with wind and petrol generators, mains chargers, alternators, etc.Measurement output for EBL (electric block of the vehicle): Enables convenient use of the (solar) current display built into the electrical block to check the solar system.Switching output "AES" (only MPP250 Duo Dig. and MPP350 Duo Dig): Causes the ELECTROLUX/ DOMETIC refrigerators with "AES" (Automatic Energy Selector) to switch automatically from gas to 12 V operation when there is plenty of excess solar power.Connection for temperature sensor (art. no. 2001): Automatic adjustment of the charging voltage to the battery temperature. Improves full charging of the weaker battery in cold weather and prevents unnecessary battery gassing in summer temperatures. Highly recommended if the battery is exposed to strong temperature fluctuations, e.g. in the engine compartment.Ready to plug in for connecting the Votronic solar display units for optimum control of the system: LCD Solar Computer S: LCD display with display range: battery voltage, charging current, charging power, stored capacity and energy (V, A, W, Ah, Wh).Electronics protected from moistureAmbient conditions, humidity: max. 95% room humidity, non-condensing Scope of delivery: Operating instructions

€129.13*

Votronic 11730 MPP 440 CI (Marine) 26A 60V MPPT solar charge controller

MPP solar controller specially designed for use on boats, yachts, etc. The electronics of the MPPT charge controller are protected against moisture. For solar modules with: up to 440 Wp module outputmax. 26.0 A module currentmax. 60 V module voltage Charging options: 1 supply battery and 1 starter battery Votronic solar controllers of the "MPP" (Maximum Power Point) series with "IU1oU2" charging characteristic are connected as a link between the solar panel(s) and battery(ies). With MPP technology, the controller automatically determines the maximum power output (MPP) of the solar modules several times per second. It then transforms the excess voltage of the solar module into a higher charging current for the battery (realized by high-frequency switching regulator technology with high efficiency). This additional charging current ensures shorter charging times and the best possible power utilization of the solar system.MPP solar controllers work fully automatically, are maintenance-free and offer the following functions: MPP charging current increase of 10 % to 30 % (efficiency > 95 %) compared to conventional controllers through the use of the latest controller technology (microprocessor). The increase in performance is particularly noticeable at cooler times of the year and e.g. during high fog conditions, low and diffuse lighting (wintering).Switchable charging characteristics for optimum charging of gel/dryfit, AGM/non-woven or acid/wet and LiFePO4 batteries (see Table 1).The charging voltage is free of peaks and regulated in such a way that overcharging of batteries is ruled out.Two battery charging outputs:Automatic charging of the main or on-board battery (Board I).Support charging and charge retention (max. 1 A) of the vehicle starter battery (Start II) with protection against overcharging.Monitoring-free charging:Standard protection against overload, overheating, reverse polarity and reverse battery discharge (if solar power is too low, e.g. at dusk, at night, etc.).Parallel/buffer operation:Maintains charging characteristics even when loads are operated simultaneously.Overcharge protection: Regulates the charging current of the battery back if there is too much solar power and the battery is full, ensures that the battery is charged to the highest possible level by immediately recharging when power is consumed."IU1oU2" charging characteristic: Defined charging voltage increase (U1) prevents harmful acid stratification and ensures equalization charging of the individual battery cells, followed by automatic trickle charging (U2).Charging cable compensation: Voltage losses on the charging cables are automatically compensated for.On-board power supply filter: Problem-free parallel operation with wind and petrol generators, mains chargers, alternators, etc.Measurement output for EBL (electric block of the vehicle): Enables convenient use of the (solar) current display built into the electrical block to check the solar system.Connection for temperature sensor (item no. 2001): Automatic adjustment of the charging voltage to the battery temperature. Improves full charging of the weaker battery in cold weather and prevents unnecessary battery gassing in summer temperatures. Highly recommended if the battery is exposed to strong temperature fluctuations, e.g. in the engine compartment.Ready to plug in for connecting the Votronic solar display units for optimum control of the system: LCD Solar Computer S: LCD display with display range: battery voltage, charging current, charging power, stored capacity and energy (V, A, W, Ah, Wh). Ambient conditions, humidity: max. 95% room humidity, non-condensing

€221.33*

Details

Votronic 1712 MPP 170 CI 10A MPPT solar charge controller 12V

Please note that the solar charge controller may only be used with solar panels up to the maximum power rating (Wp) and below the maximum permissible voltage (Voc). Furthermore, the controller is not suitable for an input-side connection (+/- solar panels) of wind, water, fuel or motor generators, power supply units, batteries or other power sources. MPP solar controller for high-quality motorhomes, caravans and boats. Votronic solar controllers of the "MPP" (Maximum Power Point) series with "IU1oU2" charging characteristic are connected as a link between solar panel(s) and battery(ies). With MPP technology, the controller automatically determines the maximum power output (MPP) of the solar modules several times per second. It then transforms the excess voltage of the solar module into a higher charging current for the battery (realized by high-frequency switching controller technology with high efficiency). This additional charging current ensures shorter charging times and the best possible power utilization of the solar system. The MPP solar controllers operate fully automatically, are maintenance-free and offer the following functions: MPP charging current increase of 10 % to 30 % (efficiency > 95 %) compared to conventional controllers thanks to the use of state-of-the-art controller technology (microprocessor). The increase in performance is particularly noticeable at cooler times of the year and e.g. during high fog conditions, low and diffuse lighting (wintering).For charging lead-gel, lead-AGM, lead-acid batteries or LiFePO4 complete batteries (with integrated BMS, balancing, safety circuit and approval!) of the specified nominal voltages and the co-supply of consumers connected to these batteries in permanently installed systems with the specified battery capacities and charging programs.The charging voltage is free of peaks and regulated in such a way that overcharging of the batteries is excluded.Two battery charging outputs: Automatic charging of the main supply on-board battery (BORD I) as well as support charging and charge retention (max. 1 A) of the vehicle starter battery (Start II) with protection against overcharging.Monitoring-free charging: Standard protection against overload, overheating, reverse polarity and battery reverse discharge (if solar power is too low, e.g. at dusk, at night, etc.).Parallel/buffer operation: Compliance with charging regulations even when loads are operated simultaneously.Overcharge protection: Regulates the charging current of the battery back if there is too much solar power and the battery is full, ensures that the battery is charged to the highest possible level by immediately recharging when power is consumed."IU1oU2" charging characteristic: Defined charging voltage increase (U1) prevents harmful acid stratification (lead) and ensures equalization charging of the individual battery cells (lead and lithium), followed by automatic trickle charging (U2).Charging cable compensation: Voltage losses on the charging cables are automatically compensated for.On-board power supply filter: problem-free parallel operation with wind and motor generators, mains chargers, alternators, etc.CI bus connection: for displaying all relevant data on a central vehicle displayMeasuring output for EBL, possibly existing electrical block in the living area of the vehicle: Enables the convenient use of a (solar) current display built into the electrical block to check the solar system.Please check the compatibility of your Schaudt electrical block (EBL) and the corresponding control and display panel in advance, as we cannot accept any liability for this.Switching output "AES" (only MPP 260 CI, MPP 360 CI and MPP 440 CI): Causes refrigerators with "AES" (Automatic Energy Selector, Electrolux / Dometic) to switch automatically from gas to 12 V operation if there is a permanent abundance of excess solar power.Connection for battery temperature sensor (art. no. 2001): In the case of lead batteries, the charging voltage is automatically adjusted to the battery temperature, resulting in a better full charge of the weaker battery in cold weather and avoiding unnecessary battery gassing and stress in summer temperatures.LiFePO4 batteries: Battery protection at high and especially low temperatures, highly recommended if the battery temperature can fall below 0°C during operation.Ready to plug in for connection of the Votronic LCD Solar Computer S solar display units for optimum control of the system.

€98.75*

Votronic 1712 MPP 170 CI 10A MPPT solar charge controller 12V

Please note that the solar charge controller may only be used with solar panels up to the maximum power rating (Wp) and below the maximum permissible voltage (Voc). Furthermore, the controller is not suitable for an input-side connection (+/- solar panels) of wind, water, fuel or motor generators, power supply units, batteries or other power sources. MPP solar controller for high-quality motorhomes, caravans and boats. Votronic solar controllers of the "MPP" (Maximum Power Point) series with "IU1oU2" charging characteristic are connected as a link between solar panel(s) and battery(ies). With MPP technology, the controller automatically determines the maximum power output (MPP) of the solar modules several times per second. It then transforms the excess voltage of the solar module into a higher charging current for the battery (realized by high-frequency switching controller technology with high efficiency). This additional charging current ensures shorter charging times and the best possible power utilization of the solar system. The MPP solar controllers operate fully automatically, are maintenance-free and offer the following functions: MPP charging current increase of 10 % to 30 % (efficiency > 95 %) compared to conventional controllers thanks to the use of state-of-the-art controller technology (microprocessor). The increase in performance is particularly noticeable at cooler times of the year and e.g. during high fog conditions, low and diffuse lighting (wintering).For charging lead-gel, lead-AGM, lead-acid batteries or LiFePO4 complete batteries (with integrated BMS, balancing, safety circuit and approval!) of the specified nominal voltages and the co-supply of consumers connected to these batteries in permanently installed systems with the specified battery capacities and charging programs.The charging voltage is free of peaks and regulated in such a way that overcharging of the batteries is excluded.Two battery charging outputs: Automatic charging of the main supply on-board battery (BORD I) as well as support charging and charge retention (max. 1 A) of the vehicle starter battery (Start II) with protection against overcharging.Monitoring-free charging: Standard protection against overload, overheating, reverse polarity and battery reverse discharge (if solar power is too low, e.g. at dusk, at night, etc.).Parallel/buffer operation: Compliance with charging regulations even when loads are operated simultaneously.Overcharge protection: Regulates the charging current of the battery back if there is too much solar power and the battery is full, ensures that the battery is charged to the highest possible level by immediately recharging when power is consumed."IU1oU2" charging characteristic: Defined charging voltage increase (U1) prevents harmful acid stratification (lead) and ensures equalization charging of the individual battery cells (lead and lithium), followed by automatic trickle charging (U2).Charging cable compensation: Voltage losses on the charging cables are automatically compensated for.On-board power supply filter: problem-free parallel operation with wind and motor generators, mains chargers, alternators, etc.CI bus connection: for displaying all relevant data on a central vehicle displayMeasuring output for EBL, possibly existing electrical block in the living area of the vehicle: Enables the convenient use of a (solar) current display built into the electrical block to check the solar system.Please check the compatibility of your Schaudt electrical block (EBL) and the corresponding control and display panel in advance, as we cannot accept any liability for this.Switching output "AES" (only MPP 260 CI, MPP 360 CI and MPP 440 CI): Causes refrigerators with "AES" (Automatic Energy Selector, Electrolux / Dometic) to switch automatically from gas to 12 V operation if there is a permanent abundance of excess solar power.Connection for battery temperature sensor (art. no. 2001): In the case of lead batteries, the charging voltage is automatically adjusted to the battery temperature, resulting in a better full charge of the weaker battery in cold weather and avoiding unnecessary battery gassing and stress in summer temperatures.LiFePO4 batteries: Battery protection at high and especially low temperatures, highly recommended if the battery temperature can fall below 0°C during operation.Ready to plug in for connection of the Votronic LCD Solar Computer S solar display units for optimum control of the system.

€162.69*

Votronic 1712 MPP 170 CI 10A MPPT solar charge controller 12V

Please note that the solar charge controller may only be used with solar panels up to the maximum power rating (Wp) and below the maximum permissible voltage (Voc). Furthermore, the controller is not suitable for an input-side connection (+/- solar panels) of wind, water, fuel or motor generators, power supply units, batteries or other power sources. MPP solar controller for high-quality motorhomes, caravans and boats. Votronic solar controllers of the "MPP" (Maximum Power Point) series with "IU1oU2" charging characteristic are connected as a link between solar panel(s) and battery(ies). With MPP technology, the controller automatically determines the maximum power output (MPP) of the solar modules several times per second. It then transforms the excess voltage of the solar module into a higher charging current for the battery (realized by high-frequency switching controller technology with high efficiency). This additional charging current ensures shorter charging times and the best possible power utilization of the solar system. The MPP solar controllers operate fully automatically, are maintenance-free and offer the following functions: MPP charging current increase of 10 % to 30 % (efficiency > 95 %) compared to conventional controllers thanks to the use of state-of-the-art controller technology (microprocessor). The increase in performance is particularly noticeable at cooler times of the year and e.g. during high fog conditions, low and diffuse lighting (wintering).For charging lead-gel, lead-AGM, lead-acid batteries or LiFePO4 complete batteries (with integrated BMS, balancing, safety circuit and approval!) of the specified nominal voltages and the co-supply of consumers connected to these batteries in permanently installed systems with the specified battery capacities and charging programs.The charging voltage is free of peaks and regulated in such a way that overcharging of the batteries is excluded.Two battery charging outputs: Automatic charging of the main supply on-board battery (BORD I) as well as support charging and charge retention (max. 1 A) of the vehicle starter battery (Start II) with protection against overcharging.Monitoring-free charging: Standard protection against overload, overheating, reverse polarity and battery reverse discharge (if solar power is too low, e.g. at dusk, at night, etc.).Parallel/buffer operation: Compliance with charging regulations even when loads are operated simultaneously.Overcharge protection: Regulates the charging current of the battery back if there is too much solar power and the battery is full, ensures that the battery is charged to the highest possible level by immediately recharging when power is consumed."IU1oU2" charging characteristic: Defined charging voltage increase (U1) prevents harmful acid stratification (lead) and ensures equalization charging of the individual battery cells (lead and lithium), followed by automatic trickle charging (U2).Charging cable compensation: Voltage losses on the charging cables are automatically compensated for.On-board power supply filter: problem-free parallel operation with wind and motor generators, mains chargers, alternators, etc.CI bus connection: for displaying all relevant data on a central vehicle displayMeasuring output for EBL, possibly existing electrical block in the living area of the vehicle: Enables the convenient use of a (solar) current display built into the electrical block to check the solar system.Please check the compatibility of your Schaudt electrical block (EBL) and the corresponding control and display panel in advance, as we cannot accept any liability for this.Switching output "AES" (only MPP 260 CI, MPP 360 CI and MPP 440 CI): Causes refrigerators with "AES" (Automatic Energy Selector, Electrolux / Dometic) to switch automatically from gas to 12 V operation if there is a permanent abundance of excess solar power.Connection for battery temperature sensor (art. no. 2001): In the case of lead batteries, the charging voltage is automatically adjusted to the battery temperature, resulting in a better full charge of the weaker battery in cold weather and avoiding unnecessary battery gassing and stress in summer temperatures.LiFePO4 batteries: Battery protection at high and especially low temperatures, highly recommended if the battery temperature can fall below 0°C during operation.Ready to plug in for connection of the Votronic LCD Solar Computer S solar display units for optimum control of the system.

€137.99*

Votronic 1713 MPP 170 CI 10A MPPT solar charge controller 12V

Beachten Sie, dass der Solar-Laderegler nur mit Solar-Panels bis zur maximalen Leistungsangabe (Wp) und unterhalb der maximal zulässigen Spannung (Voc) verwendet werden darf. Darüber hinaus ist der Regler nicht für ein eingangsseitigen Anschluss (+/- Solar-Panels) von Wind-, Wasser-, Fuel- oder Motor-Generatoren, Netzteilen, Batterien oder anderen Stromquellen geeignet. MPP Solar-Regler für hochwertige Reisemobile, Caravan und Boote. Votronic Solar-Regler der Serie „MPP“ (Maximum-Power-Point) mit „IU1oU2“-Ladekennlinie werden als Bindeglied zwischen Solar-Panel(s) und Batterie(n) geschaltet. Bei der MPP-Technologie ermittelt der Regler immerzu automatisch mehrmals pro Sekunde die maximale Leistungsausbeute (MPP) der Solar-Module. Er transformiert dann den Spannungsüberschuss des Solar-Moduls auf einen höheren Ladestrom für die Batterie um (verwirklicht durch Hochfrequenz-Schaltreglertechnologie mit hohem Wirkungsgrad). Dieser Ladestromzugewinn sorgt für kürzere Ladezeiten und die bestmögliche Leistungsausnutzung der Solaranlage. Die MPP Solar-Regler arbeiten vollautomatisch, sind wartungsfrei und bieten folgende Funktionen: MPP-Ladestrom-Zunahme gegenüber herkömmlichen Reglern durch den Einsatz modernster Reglertechnologie (Mikroprozessor) um 10 % bis 30 % (Wirkungsgrad > 95 %). Das Leistungsplus zeigt sich insbesondere zur kühleren Jahreszeit und z. B. bei Hochnebellagen, geringerer und diffuser Beleuchtung (Überwinterung).Für das Laden von Blei-Gel-, Blei-AGM-, Blei-Säure- Batterien oder LiFePO4- Komplettbatterien (mit integriertem BMS, Balancing, Sicherheitsbeschaltung und Zulassung!) der angegebenen Nennspannungen und die Mitversorgung von an diesen Batterien angeschlossenen Verbrauchern in fest installierten Systemen mit den angegebenen Batteriekapazitäten und Ladeprogrammen.Die Ladespannung ist frei von Spitzen und so geregelt, dass ein Überladen der Batterien ausgeschlossen ist.Zwei Batterie-Ladeausgänge: Automatisches Laden der Hauptversorgungs-Bord-Batterie (BORD I) sowie Stützladung und Ladeerhaltung (max. 1 A) der Fahrzeug-Starterbatterie (Start II) mit Schutz vor Überladung.Überwachungsfreie Ladung: Serienmäßiger Schutz gegen Überlast, Überhitzung, Verpolung und Batterie-Rückentladung (bei zu geringer Solarleistung z. B. Dämmerung, nachts etc.).Parallel-/Puffer-Betrieb: Einhaltung der Ladevorschriften auch bei gleichzeitigem Betrieb von Verbrauchern.Überladeschutz: Regelt den Ladestrom der Batterie bei zu viel Solarleistung und voller Batterie zurück, sorgt bei Stromverbrauch durch sofortiges Nachladen für einen möglichst hohen Ladezustand der Batterie.„IU1oU2“-Ladekennlinie: Definierte Ladespannungserhöhung (U1) verhindert schädliche Säureschichtungen (Blei) und sorgt für Ausgleichsladung der einzelnen Batteriezellen (Blei und Lith.), danach automatische Erhaltungsladung (U2).Ladekabel-Kompensation: Spannungsverluste auf den Ladekabeln werden automatisch ausgeregelt.Bordnetzfilter: Problemloser Parallelbetrieb mit Wind- und Motorgeneratoren, Netz-Ladegeräten, Lichtmaschinen etc.CI-Bus Anschluss: zur Anzeige aller relevanten Daten auf einem zentralen FahrzeugdisplayMessausgang für EBL, evtl. vorhandener Elektroblock im Wohnbereich des Fahrzeugs: Ermöglicht die bequeme Verwendung einer im Elektroblock eingebauten (Solar-) Stromanzeige zur Kontrolle der Solar-Anlage.Bitte prüfen Sie vorab unbedingt die Kompatibilität Ihres Schaudt-Elektroblocks (EBL) sowie der entsprechenden Kontroll- und Anzeigetafel, da wir hierfür keine Gewährleistung übernehmen können.Schaltausgang „AES“ (nur MPP 260 CI, MPP 360 CI und MPP 440 CI): Bewirkt bei dauerhaft reichlich Solar-Leistungsüberschuss das automatische Umschalten von Kühlschränken mit „AES“ (Automatic Energy Selector, Electrolux / Dometic) von Gas- auf 12 V-Betrieb.Anschluss für Batterie-Temperatur-Sensor (Art.-Nr. 2001): Bei Blei-Batterien erfolgt die automatische Anpassung der Ladespannung an die Batterie-Temperatur, bewirkt bei Kälte eine bessere Vollladung der schwächeren Batterie, bei sommerlichen Temperaturen wird unnötige Batteriegasung und -belastung vermieden.LiFePO4-Batterien: Batterieschutz bei hohen und insbesondere bei tiefen Temperaturen.Unbedingt empfohlen, wenn die Batterietemperatur im laufenden Betrieb unter 0°C fallen kann.Steckerfertig für den Anschluss der Votronic Solar-Anzeigegeräte LCD-Solar Computer S zur optimalen Kontrolle der Anlage.

€106.80*

Votronic 1723 MPPT 360 CI 30A MPPT solar charge controller 12V

Please note that the solar charge controller may only be used with solar panels up to the maximum power rating (Wp) and below the maximum permissible voltage (Voc). Furthermore, the controller is not suitable for an input-side connection (+/- solar panels) of wind, water, fuel or motor generators, power supply units, batteries or other power sources. MPP solar controller for high-quality motorhomes, caravans and boats. Votronic solar controllers of the "MPP" (Maximum Power Point) series with "IU1oU2" charging characteristic are connected as a link between solar panel(s) and battery(ies). With MPP technology, the controller automatically determines the maximum power output (MPP) of the solar modules several times per second. It then transforms the excess voltage of the solar module into a higher charging current for the battery (realized by high-frequency switching controller technology with high efficiency). This additional charging current ensures shorter charging times and the best possible power utilization of the solar system. The MPP solar controllers operate fully automatically, are maintenance-free and offer the following functions: MPP charging current increase of 10 % to 30 % (efficiency > 95 %) compared to conventional controllers thanks to the use of state-of-the-art controller technology (microprocessor). The increase in performance is particularly noticeable at cooler times of the year and e.g. during high fog conditions, low and diffuse lighting (wintering).For charging lead-gel, lead-AGM, lead-acid batteries or LiFePO4 complete batteries (with integrated BMS, balancing, safety circuit and approval!) of the specified nominal voltages and the co-supply of consumers connected to these batteries in permanently installed systems with the specified battery capacities and charging programs.The charging voltage is free of peaks and regulated in such a way that overcharging of the batteries is excluded.Two battery charging outputs: Automatic charging of the main supply on-board battery (BORD I) as well as support charging and charge retention (max. 1 A) of the vehicle starter battery (Start II) with protection against overcharging.Monitoring-free charging: Standard protection against overload, overheating, reverse polarity and battery reverse discharge (if solar power is too low, e.g. at dusk, at night, etc.).Parallel/buffer operation: Compliance with charging regulations even when loads are operated simultaneously.Overcharge protection: Regulates the charging current of the battery back if there is too much solar power and the battery is full, ensures that the battery is charged to the highest possible level by immediately recharging when power is consumed."IU1oU2" charging characteristic: Defined charging voltage increase (U1) prevents harmful acid stratification (lead) and ensures equalization charging of the individual battery cells (lead and lithium), followed by automatic trickle charging (U2).Charging cable compensation: Voltage losses on the charging cables are automatically compensated for.On-board power supply filter: problem-free parallel operation with wind and motor generators, mains chargers, alternators, etc.CI bus connection: for displaying all relevant data on a central vehicle displayMeasuring output for EBL, possibly existing electrical block in the living area of the vehicle: Enables the convenient use of a (solar) current display built into the electrical block to check the solar system.Please check the compatibility of your Schaudt electrical block (EBL) and the corresponding control and display panel in advance, as we cannot accept any liability for this.Switching output "AES" (only MPP 260 CI, MPP 360 CI and MPP 440 CI): Causes refrigerators with "AES" (Automatic Energy Selector, Electrolux / Dometic) to switch automatically from gas to 12 V operation if there is a permanent abundance of excess solar power.Connection for battery temperature sensor (art. no. 2001): In the case of lead batteries, the charging voltage is automatically adjusted to the battery temperature, resulting in a better full charge of the weaker battery in cold weather and avoiding unnecessary battery gassing and stress in summer temperatures.LiFePO4 batteries: Battery protection at high and especially low temperatures, highly recommended if the battery temperature can fall below 0°C during operation.Ready to plug in for connection of the Votronic LCD Solar Computer S solar display units for optimum control of the system.

€162.69*

Votronic 1712 MPP 170 CI 10A MPPT solar charge controller 12V (VAT exempt)

Please note that the solar charge controller may only be used with solar panels up to the maximum power rating (Wp) and below the maximum permissible voltage (Voc). Furthermore, the controller is not suitable for an input-side connection (+/- solar panels) of wind, water, fuel or motor generators, power supply units, batteries or other power sources. MPP solar controller for high-quality motorhomes, caravans and boats. Votronic solar controllers of the "MPP" (Maximum Power Point) series with "IU1oU2" charging characteristic are connected as a link between solar panel(s) and battery(ies). With MPP technology, the controller automatically determines the maximum power output (MPP) of the solar modules several times per second. It then transforms the excess voltage of the solar module into a higher charging current for the battery (realized by high-frequency switching controller technology with high efficiency). This additional charging current ensures shorter charging times and the best possible power utilization of the solar system. The MPP solar controllers operate fully automatically, are maintenance-free and offer the following functions: MPP charging current increase of 10 % to 30 % (efficiency > 95 %) compared to conventional controllers thanks to the use of state-of-the-art controller technology (microprocessor). The increase in performance is particularly noticeable at cooler times of the year and e.g. during high fog conditions, low and diffuse lighting (wintering).For charging lead-gel, lead-AGM, lead-acid batteries or LiFePO4 complete batteries (with integrated BMS, balancing, safety circuit and approval!) of the specified nominal voltages and the co-supply of consumers connected to these batteries in permanently installed systems with the specified battery capacities and charging programs.The charging voltage is free of peaks and regulated in such a way that overcharging of the batteries is excluded.Two battery charging outputs: Automatic charging of the main supply on-board battery (BORD I) as well as support charging and charge retention (max. 1 A) of the vehicle starter battery (Start II) with protection against overcharging.Monitoring-free charging: Standard protection against overload, overheating, reverse polarity and battery reverse discharge (if solar power is too low, e.g. at dusk, at night, etc.).Parallel/buffer operation: Compliance with charging regulations even when loads are operated simultaneously.Overcharge protection: Regulates the charging current of the battery back if there is too much solar power and the battery is full, ensures that the battery is charged to the highest possible level by immediately recharging when power is consumed."IU1oU2" charging characteristic: Defined charging voltage increase (U1) prevents harmful acid stratification (lead) and ensures equalization charging of the individual battery cells (lead and lithium), followed by automatic trickle charging (U2).Charging cable compensation: Voltage losses on the charging cables are automatically compensated for.On-board power supply filter: problem-free parallel operation with wind and motor generators, mains chargers, alternators, etc.CI bus connection: for displaying all relevant data on a central vehicle displayMeasuring output for EBL, possibly existing electrical block in the living area of the vehicle: Enables the convenient use of a (solar) current display built into the electrical block to check the solar system.Please check the compatibility of your Schaudt electrical block (EBL) and the corresponding control and display panel in advance, as we cannot accept any liability for this.Switching output "AES" (only MPP 260 CI, MPP 360 CI and MPP 440 CI): Causes refrigerators with "AES" (Automatic Energy Selector, Electrolux / Dometic) to switch automatically from gas to 12 V operation if there is a permanent abundance of excess solar power.Connection for battery temperature sensor (art. no. 2001): In the case of lead batteries, the charging voltage is automatically adjusted to the battery temperature, resulting in a better full charge of the weaker battery in cold weather and avoiding unnecessary battery gassing and stress in summer temperatures.LiFePO4 batteries: Battery protection at high and especially low temperatures, highly recommended if the battery temperature can fall below 0°C during operation.Ready to plug in for connection of the Votronic LCD Solar Computer S solar display units for optimum control of the system.

€83.99*

Details

VOTRONIC cable set 2007 EBL to charge controller connection cable 1m

for connecting all standard charge controllers to an existing Schaudt electric block (EBL).Features Length: 1m For all standard charge controllers Scope of delivery1 x EBL connection cable 1m

€17.45*

Votronic 11717 MPP 260 CI (Marine) 20A MPPT solar charge controller 12V (VAT Exempt)

Product information "Votronic 11717 MPP 260 CI (Marine) 20A MPPT solar charge controller 12V (VAT Exempt)"

Votronic 11717 MPP 260 CI (Marine) 20A MPPT solar charge controller 12V (VAT Exempt)

Product information "Votronic 11717 MPP 260 CI (Marine) 20A MPPT solar charge controller 12V (VAT Exempt)"

Login