With the battery disconnect switch, your battery can be safely disconnected to reduce power consumption when the device, vehicle or boat is not in use. The switch is suitable for automotive electronics, electrical products and all types of 12V/24V vehicles, boats, motorhomes, etc. The practical rotary switch is very easy to use and works smoothly. ON (green) means switching on the circuit and OFF (red) means switching off. Switch the power supply on or off safely to avoid electric shock. Features Suitable for 12V / 24VContinuous current 12V DC: 275AIntermittent current 12V DC: 455AInstantaneous current 12V DC: 1250AWeight: 260gDimensions of disconnector: 69 x 69 x 75mmDimensions for the 4 removable cable glands: 45 x 20mm Guard and locking service The switch can be used as an independent unit or in parallel with other switches. It can effectively protect the power supply, reduce battery loss and extend battery life. Durable material The disconnect switch is made of CE-certified, high-quality ABS flame-retardant reinforced nylon and silver-plated red copper bolts. It is resistant to moisture, UV and ageing and has a long service life. The rear cover is insulated to prevent short circuits, meet safety requirements and effectively prevent electrical accidents. Easy installation The battery isolator can be installed quickly and easily. Attention must be paid to the arrangement of the positive and negative wires, then install the corresponding lining plate and tighten the four screws to prevent the cable connector from being exposed to the air and oxidized. Scope of delivery: 1x battery switch1x bottom cover4x screws + nuts for fastening

With the main switch / battery selector switch, two batteries can be switched on and off simultaneously and controlled separately to reduce power consumption when the device, vehicle or boat is not in use. The switch is suitable for automotive electronics, electrical products and all types of 12V/24V/36V vehicles, boats, motorhomes, etc.The practical rotary switch is very easy to operate and works smoothly. With switch position 1 or 2 one of the connected batteries can be switched on, with 1 & 2 both are connected to the circuit and OFF (red) means both batteries are switched off. When the device or vehicle is not in use, the switch can be used to safely disconnect the connection between the battery and the electrical product, thus reducing energy consumption. Features Suitable for 6V/12V/24V/36V Continuous current 12V DC: 175A Intermittent current 12V DC: 300A Maximum current (short-term): 1000A Weight: 260g Selector switch dimensions: 134 x 134 x 77mm Connection terminal: M5 Guard and locking service The switch can be used as an independent unit or in parallel with other switches. It can effectively protect the power supply, reduce battery loss and extend battery life. The switch is non-removable. Durable material The selector switch is made of CE-certified, high-quality ABS flame-retardant reinforced nylon and silver-plated red copper bolts. It is resistant to moisture, UV and ageing and has a long service life. The rear cover is insulated to prevent short circuits, meet safety requirements and effectively prevent electrical accidents. Easy installation The battery selector switch can be installed quickly and easily. Pay attention to the arrangement of the positive and negative wires, then install the corresponding lining plate and tighten the four screws to prevent the cable connector from being exposed to the air and oxidized.

The twilight switch switches e.g. lamps on at dusk and off again at dawn. (for weekend homes with battery power supply, sailing yachts, caravans, etc.) Switching output: relay 1x UM max. 3 A. The light intensity sensitivity can be changed by partially covering the sensor mechanically. Wiring diagram for 12 V load, without external power source

With the battery disconnect switch, your battery can be safely disconnected to reduce power consumption when the device, vehicle or boat is not in use. The switch is suitable for automotive electronics, electrical products and all types of 12V/24V vehicles, boats, motorhomes, etc. The practical rotary switch is very easy to use and works smoothly. ON (green) means switching on the circuit and OFF (red) means switching off. Switch the power supply on or off safely to avoid electric shock. Features Suitable for 12V / 24VContinuous current 12V DC: 275AIntermittent current 12V DC: 455AInstantaneous current 12V DC: 1250AWeight: 260gDimensions of disconnector: 69 x 69 x 75mmDimensions for the 4 removable cable glands: 45 x 20mm Guard and locking service The switch can be used as an independent unit or in parallel with other switches. It can effectively protect the power supply, reduce battery loss and extend battery life. Durable material The disconnect switch is made of CE-certified, high-quality ABS flame-retardant reinforced nylon and silver-plated red copper bolts. It is resistant to moisture, UV and ageing and has a long service life. The rear cover is insulated to prevent short circuits, meet safety requirements and effectively prevent electrical accidents. Easy installation The battery isolator can be installed quickly and easily. Attention must be paid to the arrangement of the positive and negative wires, then install the corresponding lining plate and tighten the four screws to prevent the cable connector from being exposed to the air and oxidized. Scope of delivery: 1x battery switch1x bottom cover4x screws + nuts for fastening

Battery disconnector 6 V, 12 V, 24 V The battery isolating switch is suitable for preventing short circuits and unwanted battery discharge. The battery disconnector is connected to the negative terminal. Advantages: Max. Max. load capacity: 100 A Operating voltage: 6 Volt/ 12 Volt/ 24 Volt Size (LxWxH): approx. 8.5 x 3.5 x 3.5 cm Single-pole battery isolating switch Interrupts the entire circuit by simply turning the knob Prevents battery discharge, electrical fires, unauthorized operation, etc. Battery disconnect switch is connected to the pole Avoids tedious unscrewing of battery cables when charging Quick and easy installation Application: MOTOR VEHICLES Caravan and motorhome

Battery switch / battery isolator 6V- 24V 100A Natoknochen

With the main switch / battery selector switch, two batteries can be switched on and off simultaneously and controlled separately to reduce power consumption when the device, vehicle or boat is not in use. The switch is suitable for automotive electronics, electrical products and all types of 12V/24V/36V vehicles, boats, motorhomes, etc.The practical rotary switch is very easy to operate and works smoothly. With switch position 1 or 2 one of the connected batteries can be switched on, with 1 & 2 both are connected to the circuit and OFF (red) means both batteries are switched off. When the device or vehicle is not in use, the switch can be used to safely disconnect the connection between the battery and the electrical product, thus reducing energy consumption. Features Suitable for 12V/24V/36VContinuous current 12V DC: 200AIntermittent current 12V DC: 300AMaximum current (short-term): 1000AWeight: 260gSelector switch dimensions: 69 x 69 x 74mmDimensions for the 4 removable cable glands: 45 x 20mmConnection terminal: M8 Guard and locking service The switch can be used as an independent unit or in parallel with other switches. It can effectively protect the power supply, reduce battery loss and extend battery life. The switch is non-removable. Durable material The selector switch is made of CE-certified, high-quality ABS flame-retardant reinforced nylon and silver-plated red copper bolts. It is resistant to moisture, UV and ageing and has a long service life. The rear cover is insulated to prevent short circuits, meet safety requirements and effectively prevent electrical accidents. Easy installation The battery selector switch can be installed quickly and easily. Attention must be paid to the arrangement of the positive and negative wires, then install the corresponding lining plate and tighten the four screws to prevent the cable connector from being exposed to the air and oxidized. Scope of delivery: 1x battery switch4x removable side plate1x base plate4x screw4x nut

The ultra-fast Filax transfer switch from Victron Energy (MPN SDFI0000000) was developed to switch important or sensitive loads such as computers, industrial control devices or modern consumer electronics from one AC power source to another. The main power source is typically the mains, a generator or a shore connection. An inverter is usually used as an alternative source. With its switching time of less than 20 milliseconds, even sensitive loads continue to operate without interruption.The Filax is not designed to supply household appliances with high power consumption, such as washing machines or electric motors. Gap switching function The Filax is a transfer switch with a bridging (non-bridging) switching function. The maximum time for switching loads is 16 ms. The load is normally supplied via the main power source and is switched to the alternative source in the following cases: The voltage of the main power source falls below the threshold value. The frequency of the main power source falls below the low frequency threshold or exceeds the high frequency threshold. Switching back from the alternative power source to the main power source takes place as soon as the voltage and frequency values of the main power source are within the limit values specified for switching back for 30 seconds. Technical data Max. Current: 16A Max. Max. time for switching: 16 ms Switching delay for switching back: 30 seconds Operating temperature range: -20°C - +50°C Humidity (non-condensing): Max. 95% Protection class: IP65 Weight: 0.8 kg Dimensions: 120 x 255 x 75 mm Installation Install the Filax in a dry and well-ventilated environment. The input cables from the generator / main power supply and the output cables to the devices must be connected in accordance with the wiring diagram. If a load of less than 850 watts is connected, the wire jumpers must be removed. The frequency (50 Hz or 60 Hz) is set by means of a jumper. If the jumper is not set for the frequency, the switching threshold values for the voltage are incorrect. Both inputs must be protected against current values of over 16 amperes. The front cover of the housing is attached using the four screws supplied. The Filax is now ready for use. Scope of delivery: 1x Victron Energy Filax transfer switch SDFI00000004x fixing screws1x instruction manual

Battery isolator switch 6 V, 12 V, 24 V red The switch can be individually connected to the battery thanks to the rotatable connection. The pole terminal is screwed to the negative pole of the battery. The power supply is interrupted or opened by opening the rotary wheel (red). This allows you to disconnect the battery from the mains without having to unscrew it. This is also effective if your car is not used for a longer period of time. This also provides a very simple and effective anti-theft device. Advantages: Max. Load capacity: 100 A Operating voltage: 6 Volt/ 12 Volt/ 24 Volt Size (LxWxH): approx. 58 x 52 x 52 cm Single-pole battery disconnector Interrupts the entire circuit by simply turning the knob Prevents battery discharge, electrical fires, unauthorized operation, etc. Battery disconnect switch is connected to the pole Avoids tedious unscrewing of battery cables when charging Quick and easy installation Application: MOTOR VEHICLES Caravan and motorhome

The Votronic switch panel 2 x 16 A S (MPN 1291) for 12V and 24V systems has been specially developed for use in motorhomes. The integrated individual switches can be used to switch connected consumer groups on or off separately. The switches can each be loaded with 2x 8A or 1x 16A. Important product features: 2 individual switches 2xUM with flat plug connection Load capacity: max. 2x 8A or 1x 16A Suitable for 12V and 24V systemsDimensions: 47 x 85 x 25 mm The switch panel 2 x 16 A is part of the Votronic switch and fuse panel series which, in addition to panels for switches, main switches and fuses, also includes a USB port panel and a socket outlet panel with the same look. Scope of delivery: 1x Votronic 1291 switch panel 2x 16A 12V/24V

The Votronic switch panel 16A S (MPN 1289) for 12V and 24V systems has been specially developed for use in motorhomes. With the integrated individual switch, connected consumer groups can be easily switched on or off. The switch can be loaded with 2x 8A or 1x 16A. Important product features: Single switch 2xUM with flat plug connectionLoad capacity: max. 2x 8A or 1x 16ASuitable for 12V and 24V systems The 16 A switch panel is part of the Votronic switch and fuse panel series which, in addition to panels for switches, main switches and fuses, also includes a USB port panel and a socket outlet panel in the same design. An internationally understandable labeling sheet is available for labeling the panel. The pictogram foil is self-adhesive, abrasion-resistant and corresponds to the Votronic front panel design in terms of size and font. Scope of delivery: 1x Votronic 1289 single switch panel 16A S 12V

The Votronic switch panel 4S 12/24 (MPN 1288) for 12V & 24V systems has been specially developed for use in motorhomes. This panel is equipped with four separate ON/OFF switches with which you can activate or deactivate different consumer groups individually. Each switch has its own indicator LED and a maximum load of 8A. Switch panel 4 S 4 ON/OFF switches, each with a load capacity of 8A, with indicator LEDConnection via screw terminalsThe connections are designed for cable cross-sections up to 4 mm²The VOTRONIC switch panel 4S 12/24 is suitable for both 12 V and 24 V Scope of delivery: 1x Votronic 1288 switch panel 4S 12/24

The Votronic switch panel 4S 12/24 (MPN 1288) for 12V & 24V systems has been specially developed for use in motorhomes. This panel is equipped with four separate ON/OFF switches with which you can activate or deactivate different consumer groups individually. Each switch has its own indicator LED and a maximum load of 8A. Switch panel 4 S 4 ON/OFF switches, each with a load capacity of 8A, with indicator LEDConnection via screw terminalsThe connections are designed for cable cross-sections up to 4 mm²The VOTRONIC switch panel 4S 12/24 is suitable for both 12 V and 24 V Scope of delivery: 1x Votronic 1288 switch panel 4S 12/24

The Votronic main switch panel 20A S (MPN 1295) was specially developed for use in motorhomes. This panel serves as a main switch for connected consumers or consumer groups. It has a 20A overcurrent switch which is automatically reset to the 0 position if the continuous current exceeds 20A (thermal tripping). Important product features: Main switch with 20A overcurrent switch Thermally triggered overload protection ensures safety on board, can be overloaded for a short time tripping at more than 20A continuous current with return of the switch to the 0 position Suitable for 12V and 24V systems Quality made in Germany The Votronic main switch panel with 20A switching capacity and a smart look is designed for installation in motorhomes. It is just one part of a whole series of coordinated panels. In addition to the main switch, the Votronic switch and fuse panel series also offers panels for switches, main switches and fuses, as well as a socket outlet panel. An internationally understandable labeling sheet is available for labeling the panel. The pictogram foil is self-adhesive, abrasion-resistant and corresponds to the Votronic front panel design in terms of size and font. Scope of delivery: 1x Votronic 1295 main switch panel 20A S 12V 24V with thermal fuse

The Growatt ATS-S is a single-phase transfer switch and controls the changeover of the switching device both when connected to the power grid and in stand-alone operation in order to provide power to the EPS load. It is used with Growatt inverters from the SPH and SPA series. The ATS-S can automatically switch to stand-alone operation in the event of a power failure and thus supply everything else with power to guarantee smooth operation. Its natural cooling concept is used to prevent overheating. Technical data Voltage: 230 VFrequency: 50/60 HzMax. Current: 30 AProtection class: IP65Operating temperature: -25°C - +50°CWeight: 2.38 kgDimensions: 250 x 200 x 86 mm Scope of delivery: 1x Growatt ATS-S 1-phase transfer switch

The Growatt ATS-S is a single-phase transfer switch and controls the changeover of the switching device both when connected to the power grid and in stand-alone operation in order to provide power to the EPS load. It is used with Growatt inverters from the SPH and SPA series. The ATS-S can automatically switch to stand-alone operation in the event of a power failure and thus supply everything else with power to guarantee smooth operation. Its natural cooling concept is used to prevent overheating. Technical data Voltage: 230 VFrequency: 50/60 HzMax. Current: 30 AProtection class: IP65Operating temperature: -25°C - +50°CWeight: 2.38 kgDimensions: 250 x 200 x 86 mm Scope of delivery: 1x Growatt ATS-S 1-phase transfer switch

The Growatt ATS-T is a 3-phase transfer switch and controls the changeover of the switching device to provide power to the EPS load both when connected to the grid and in stand-alone operation. It is used with Growatt inverters from the SPH and SPA series. The ATS-T can automatically switch to stand-alone operation in the event of a power failure and thus supply everything else with power to guarantee smooth operation. Its natural cooling concept is used to prevent overheating. Technical data Voltage: 230V/400VacFrequency: 50/60 HzMax. Current: 30 AProtection class: IP65Operating temperature: -25°C - +50°CWeight: 3.8 kgDimensions: 312 x 295.4 x 85 mm Scope of delivery: 1x Growatt ATS-T 3-phase transfer switch