NOQON SCD25 MPPT solar charge controller Dual 12V 350Wp 50V 25A High efficiency and safety. The NOQON MPPT solar charge controller for motorhomes, caravans, camper vans and the marine sector. A solar charger is supplied with energy via solar modules and then stores it in batteries. Using the latest and fastest technology, the NOQON SCD25 MPPT Solar Charge Controller Dual 12V 350Wp 50V 25A maximizes this energy production and intelligently directs it to fully charge the batteries in as short a time as possible. The MPPT charge controllers from NOQON maintain the functionality of the battery and thus extend its service life. NOQON MPPT solar charge controllers with "IU1oU2" charging characteristic are connected as a link between the solar panel(s) and the battery(ies). With MPPT technology, the controller automatically determines the maximum power output (MPP) of the solar modules several times per second. It then transforms the excess voltage of the solar module into a higher charging current for the battery (realized by high-frequency switching controller technology with high efficiency). This additional charging current ensures shorter charging times and the best possible power utilization of the solar system. The NOQON MPPT solar charge controllers operate fully automatically, are maintenance-free and offer the following functions: Two battery charging outputs: For main supply on-board battery as well as backup charging and charge retention of the starter battery Switchable charging characteristics for optimum charging of lead gel/dryfit, AGM/fleece or acid/wet batteries as well as LiFePO4 batteries Standard protection against overload, overcharging, overheating, reverse polarity and reverse battery discharge Charging cable compensation: voltage losses on the charging cables are automatically compensated for MPP charging current increase of 10% to 30% compared to conventional controllers thanks to the use of state-of-the-art controller technology (microprocessor). The increase in performance is particularly noticeable in the cooler months of the year and, for example, during high fog conditions, low and diffuse lighting (wintering). Switchable charging characteristics for optimum charging of lead-gel/dryfit, AGM/fleece or acid/wet batteries as well as LiFePO4 batteries. The charging voltage is free of peaks and regulated in such a way that the batteries cannot be overcharged. Monitoring-free charging: Standard protection against overload, overheating, reverse polarity and battery back-discharge (if solar power is too low, e.g. at dusk, at night, etc.). Parallel/buffer operation: Compliance with charging regulations even with simultaneous operation of consumers. Overcharge protection: Regulates the charging current of the battery back if there is too much solar power and the battery is full, ensures that the battery is charged to the highest possible level by immediately recharging when power is consumed. IU1oU2" charging characteristic: Defined charging voltage increase (U1) prevents harmful acid stratification (lead) and ensures equalization charging of the individual battery cells (lead and lithium), followed by automatic trickle charging (U2). Charging cable compensation: Voltage losses on the charging cables are automatically compensated for. On-board network filter: Problem-free parallel operation with wind and motor generators, mains chargers, alternators, etc. Simple integration into the vehicle network Tested quality Certificates: CE, ROHS NOQON MPPT solar charge controllers have the CE mark. 2-year warranty on all NOQON MPPT solar charge controllers. MPPT: Ultra-fast maximum power point tracking By continuously monitoring the voltage and current output of the solar (PV) modules, MPPT technology ensures that all available energy is drawn from the photovoltaic modules and stored. The benefit of this is most noticeable when the sky is partly cloudy and the light intensity is constantly changing. NOQON MPPT charge controllers comply with the latest safety standards. NOQON charge controllers are CE approved. Quality components The NOQON SCD25 MPPT solar charge controller Dual 12V 350Wp 50V 25A is very robustly built, but thanks to its active fan cooling it is also extremely efficient and whisper-quiet, making it suitable for continuous operation in motorhomes. Thanks to high-quality electronic components and the latest high-frequency switching controller technology, the solar charge controller is able to achieve high levels of efficiency with minimal power consumption. In addition to active fan cooling, the sturdy, ribbed and lightweight aluminum housing ensures maximum passive cooling and therefore quiet continuous operation. Overload/overheating protection MPPT solar charge controller Thanks to the many integrated protective circuits, durable electronics and intelligent microprocessor control, the NOQON SCD25 MPPT solar charge controller Dual 12V 350Wp 50V 25A guarantees reliable operation. The MPPT solar charge controller is electronically protected twice against overload and protects itself against adverse installation conditions (e.g. poor ventilation, excessively high ambient temperatures) by gradually reducing the charging power. The NOQON SCD25 MPPT solar charge controller Dual 12V 350Wp 50V 25A was built in accordance with the applicable safety guidelines It may only be used For charging lead-gel/AGM/acid batteries or LiFePO4 complete batteries (with integrated BMS, balancing, safety circuitry and approval!) of the specified nominal voltages and the co-supply of consumers connected to these batteries in permanently installed systems with the specified battery capacities and charging programs. Only solar panels up to the maximum power rating (WP) of the MPPT solar charge controller used. Only with solar panels below the maximum permissible voltage (VOC). With the specified cable cross-sections at the charging outputs and at the panel input. With fuses of the specified ratings near the battery to protect the cabling between the battery and charging outputs. In a well-ventilated room, protected against rain, moisture, dust and aggressive battery gases and in a non-condensing environment. In perfect technical condition. Only solar modules and no other power sources may be connected to the plus and minus input terminals for the solar panel. NOQON MPPT solar charge controller Areas of application: Suitable for: Wet batteries (lead-acid batteries) AGM batteries (VRLA) GEL batteries (VRLA) Lithium-ion batteries (LiFePO4) Areas of application: Motorhome Camping bus - Camping van caravan Marine - Boat caravan Garden house Mountain hut Scope of delivery: NOQON SCD25 MPPT solar charge controller Dual 12V 350Wp 50V 25A Instruction manual with technical data and fault diagnosis (English/German) 2 year warranty MPPT charge controller accessories: With the NOQON solar charge controller monitor NSM1 you can remotely control your NOQON SCD25 MPPT solar charge controller Dual 12V 350Wp 50V 25A thanks to the supplied connection cable.

NOQON SCD25 MPPT solar charge controller Dual 12V 350Wp 50V 25A High efficiency and safety. The NOQON MPPT solar charge controller for motorhomes, caravans, camper vans and the marine sector. A solar charger is supplied with energy via solar modules and then stores it in batteries. Using the latest and fastest technology, the NOQON SCD25 MPPT Solar Charge Controller Dual 12V 350Wp 50V 25A maximizes this energy production and intelligently directs it to fully charge the batteries in as short a time as possible. The MPPT charge controllers from NOQON maintain the functionality of the battery and thus extend its service life. NOQON MPPT solar charge controllers with "IU1oU2" charging characteristic are connected as a link between the solar panel(s) and the battery(ies). With MPPT technology, the controller automatically determines the maximum power output (MPP) of the solar modules several times per second. It then transforms the excess voltage of the solar module into a higher charging current for the battery (realized by high-frequency switching controller technology with high efficiency). This additional charging current ensures shorter charging times and the best possible power utilization of the solar system. The NOQON MPPT solar charge controllers operate fully automatically, are maintenance-free and offer the following functions: Two battery charging outputs: For main supply on-board battery as well as backup charging and charge retention of the starter battery Switchable charging characteristics for optimum charging of lead gel/dryfit, AGM/fleece or acid/wet batteries as well as LiFePO4 batteries Standard protection against overload, overcharging, overheating, reverse polarity and reverse battery discharge Charging cable compensation: voltage losses on the charging cables are automatically compensated for MPP charging current increase of 10% to 30% compared to conventional controllers thanks to the use of state-of-the-art controller technology (microprocessor). The increase in performance is particularly noticeable in the cooler months of the year and, for example, during high fog conditions, low and diffuse lighting (wintering). Switchable charging characteristics for optimum charging of lead-gel/dryfit, AGM/fleece or acid/wet batteries as well as LiFePO4 batteries. The charging voltage is free of peaks and regulated in such a way that the batteries cannot be overcharged. Monitoring-free charging: Standard protection against overload, overheating, reverse polarity and battery back-discharge (if solar power is too low, e.g. at dusk, at night, etc.). Parallel/buffer operation: Compliance with charging regulations even with simultaneous operation of consumers. Overcharge protection: Regulates the charging current of the battery back if there is too much solar power and the battery is full, ensures that the battery is charged to the highest possible level by immediately recharging when power is consumed. IU1oU2" charging characteristic: Defined charging voltage increase (U1) prevents harmful acid stratification (lead) and ensures equalization charging of the individual battery cells (lead and lithium), followed by automatic trickle charging (U2). Charging cable compensation: Voltage losses on the charging cables are automatically compensated for. On-board network filter: Problem-free parallel operation with wind and motor generators, mains chargers, alternators, etc. Simple integration into the vehicle network Tested quality Certificates: CE, ROHS NOQON MPPT solar charge controllers have the CE mark. 2-year warranty on all NOQON MPPT solar charge controllers. MPPT: Ultra-fast maximum power point tracking By continuously monitoring the voltage and current output of the solar (PV) modules, MPPT technology ensures that all available energy is drawn from the photovoltaic modules and stored. The benefit of this is most noticeable when the sky is partly cloudy and the light intensity is constantly changing. NOQON MPPT charge controllers comply with the latest safety standards. NOQON charge controllers are CE approved. Quality components The NOQON SCD25 MPPT solar charge controller Dual 12V 350Wp 50V 25A is very robustly built, but thanks to its active fan cooling it is also extremely efficient and whisper-quiet, making it suitable for continuous operation in motorhomes. Thanks to high-quality electronic components and the latest high-frequency switching controller technology, the solar charge controller is able to achieve high levels of efficiency with minimal power consumption. In addition to active fan cooling, the sturdy, ribbed and lightweight aluminum housing ensures maximum passive cooling and therefore quiet continuous operation. Overload/overheating protection MPPT solar charge controller Thanks to the many integrated protective circuits, durable electronics and intelligent microprocessor control, the NOQON SCD25 MPPT solar charge controller Dual 12V 350Wp 50V 25A guarantees reliable operation. The MPPT solar charge controller is electronically protected twice against overload and protects itself against adverse installation conditions (e.g. poor ventilation, excessively high ambient temperatures) by gradually reducing the charging power. The NOQON SCD25 MPPT solar charge controller Dual 12V 350Wp 50V 25A was built in accordance with the applicable safety guidelines It may only be used For charging lead-gel/AGM/acid batteries or LiFePO4 complete batteries (with integrated BMS, balancing, safety circuitry and approval!) of the specified nominal voltages and the co-supply of consumers connected to these batteries in permanently installed systems with the specified battery capacities and charging programs. Only solar panels up to the maximum power rating (WP) of the MPPT solar charge controller used. Only with solar panels below the maximum permissible voltage (VOC). With the specified cable cross-sections at the charging outputs and at the panel input. With fuses of the specified ratings near the battery to protect the cabling between the battery and charging outputs. In a well-ventilated room, protected against rain, moisture, dust and aggressive battery gases and in a non-condensing environment. In perfect technical condition. Only solar modules and no other power sources may be connected to the plus and minus input terminals for the solar panel. NOQON MPPT solar charge controller Areas of application: Suitable for: Wet batteries (lead-acid batteries) AGM batteries (VRLA) GEL batteries (VRLA) Lithium-ion batteries (LiFePO4) Areas of application: Motorhome Camping bus - Camping van caravan Marine - Boat caravan Garden house Mountain hut Scope of delivery: NOQON SCD25 MPPT solar charge controller Dual 12V 350Wp 50V 25A Instruction manual with technical data and fault diagnosis (English/German) 2 year warranty MPPT charge controller accessories: With the NOQON solar charge controller monitor NSM1 you can remotely control your NOQON SCD25 MPPT solar charge controller Dual 12V 350Wp 50V 25A thanks to the supplied connection cable.

VOLTIMA SCD12 MPPT solar charge controller Dual 12V 165Wp 50V 12A High efficiency and safety. The VOLTIMA MPPT solar charge controller for motorhomes, caravans, camper vans and the marine sector. A solar charger is supplied with energy via solar modules and then stores it in batteries. Using the latest and fastest technology, the VOLTIMA SCD12 MPPT Solar Charge Controller Dual 12V 165Wp 50V 12A maximizes this energy production and intelligently directs it to fully charge the batteries in as short a time as possible. The MPPT charge controllers from VOLTIMA maintain the functionality of the battery and thus extend its service life. VOLTIMA MPPT solar charge controllers with "IU1oU2" charging characteristic are connected as a link between the solar panel(s) and the battery(ies). With MPPT technology, the controller automatically determines the maximum power output (MPP) of the solar modules several times per second. It then transforms the excess voltage of the solar module into a higher charging current for the battery (realized by high-frequency switching controller technology with high efficiency). This additional charging current ensures shorter charging times and the best possible power utilization of the solar system. The VOLTIMA MPPT solar charge controllers operate fully automatically, are maintenance-free and offer the following functions: Two battery charging outputs: For main supply on-board battery as well as backup charging and charge retention of the starter battery Switchable charging characteristics for optimum charging of lead gel/dryfit, AGM/fleece or acid/wet batteries as well as LiFePO4 batteries Standard protection against overload, overcharging, overheating, reverse polarity and reverse battery discharge Charging cable compensation: voltage losses on the charging cables are automatically compensated for MPP charging current increase of 10% to 30% compared to conventional controllers thanks to the use of state-of-the-art controller technology (microprocessor). The increase in performance is particularly noticeable in the cooler months of the year and, for example, during high fog, low and diffuse lighting (wintering). Switchable charging characteristics for optimum charging of lead-gel/dryfit, AGM/fleece or acid/wet batteries as well as LiFePO4 batteries. The charging voltage is free of peaks and regulated in such a way that the batteries cannot be overcharged. Monitoring-free charging: Standard protection against overload, overheating, reverse polarity and battery back-discharge (if solar power is too low, e.g. at dusk, at night, etc.). Parallel/buffer operation: Compliance with charging regulations even with simultaneous operation of consumers. Overcharge protection: Regulates the charging current of the battery back if there is too much solar power and the battery is full, ensures that the battery is charged to the highest possible level by immediately recharging when power is consumed. IU1oU2" charging characteristic: Defined charging voltage increase (U1) prevents harmful acid stratification (lead) and ensures equalization charging of the individual battery cells (lead and lithium), followed by automatic trickle charging (U2). Charging cable compensation: Voltage losses on the charging cables are automatically compensated for. On-board network filter: Problem-free parallel operation with wind and motor generators, mains chargers, alternators, etc. Simple integration into the vehicle network Tested quality Certificates: CE, ROHS VOLTIMA MPPT solar charge controllers have the CE mark. 2-year warranty on all VOLTIMA MPPT solar charge controllers. MPPT: Ultra-fast maximum power point tracking By continuously monitoring the voltage and current output of the solar (PV) modules, MPPT technology ensures that all available energy is drawn from the photovoltaic modules and stored. The benefit of this is most noticeable when the sky is partly cloudy and the light intensity is constantly changing. VOLTIMA MPPT charge controllers comply with the latest safety standards. VOLTIMA charge controllers are CE approved. Quality components The VOLTIMA SCD12 MPPT solar charge controller Dual 12V 165Wp 50V 12A is very robustly built, but thanks to its active fan cooling it is also extremely efficient and whisper-quiet, making it suitable for continuous operation in motorhomes. Thanks to high-quality electronic components and the latest high-frequency switching controller technology, the solar charge controller is able to achieve high levels of efficiency with minimal power consumption. In addition to active fan cooling, the sturdy, ribbed and lightweight aluminum housing ensures maximum passive cooling and therefore quiet continuous operation. Overload/overheating protection MPPT solar charge controller Thanks to the many integrated protective circuits, durable electronics and intelligent microprocessor control, the VOLTIMA SCD12 MPPT solar charge controller Dual 12V 165Wp 50V 12A guarantees reliable operation. The MPPT solar charge controller is electronically protected twice against overload and protects itself against adverse installation conditions (e.g. poor ventilation, excessively high ambient temperatures) by gradually reducing the charging power. The VOLTIMA SCD12 MPPT solar charge controller Dual 12V 165Wp 50V 12A was built in accordance with the applicable safety guidelines It may only be used For charging lead-gel/AGM/acid batteries or LiFePO4 complete batteries (with integrated BMS, balancing, safety circuitry and approval!) of the specified nominal voltages and the co-supply of consumers connected to these batteries in permanently installed systems with the specified battery capacities and charging programs. Only solar panels up to the maximum power rating (WP) of the MPPT solar charge controller used. Only with solar panels below the maximum permissible voltage (VOC). With the specified cable cross-sections at the charging outputs and at the panel input. With fuses of the specified ratings near the battery to protect the cabling between the battery and charging outputs. In a well-ventilated room, protected against rain, moisture, dust and aggressive battery gases and in a non-condensing environment. In perfect technical condition. Only solar modules and no other power sources may be connected to the plus and minus input terminals for the solar panel. VOLTIMA MPPT solar charge controller Areas of application: Suitable for: Wet batteries (lead-acid batteries) AGM batteries (VRLA) GEL batteries (VRLA) Lithium-ion batteries (LiFePO4) Areas of application: Motorhome Camping bus - Camping van caravan Marine - Boat caravan Garden house Mountain hut Scope of delivery: VOLTIMA SCD12 MPPT solar charge controller Dual 12V 165Wp 50V 12A Instruction manual with technical data and fault diagnosis (English/German) 2 year warranty MPPT charge controller accessories: With the VOLTIMA solar charge controller monitor VSM1 you can remotely control your VOLTIMA SCD12 MPPT solar charge controller Dual 12V 165Wp 50V 12A thanks to the supplied connection cable.

VOLTIMA SCD12 MPPT solar charge controller Dual 12V 165Wp 50V 12A High efficiency and safety. The VOLTIMA MPPT solar charge controller for motorhomes, caravans, camper vans and the marine sector. A solar charger is supplied with energy via solar modules and then stores it in batteries. Using the latest and fastest technology, the VOLTIMA SCD12 MPPT Solar Charge Controller Dual 12V 165Wp 50V 12A maximizes this energy production and intelligently directs it to fully charge the batteries in as short a time as possible. The MPPT charge controllers from VOLTIMA maintain the functionality of the battery and thus extend its service life. VOLTIMA MPPT solar charge controllers with "IU1oU2" charging characteristic are connected as a link between the solar panel(s) and the battery(ies). With MPPT technology, the controller automatically determines the maximum power output (MPP) of the solar modules several times per second. It then transforms the excess voltage of the solar module into a higher charging current for the battery (realized by high-frequency switching controller technology with high efficiency). This additional charging current ensures shorter charging times and the best possible power utilization of the solar system. The VOLTIMA MPPT solar charge controllers operate fully automatically, are maintenance-free and offer the following functions: Two battery charging outputs: For main supply on-board battery as well as backup charging and charge retention of the starter battery Switchable charging characteristics for optimum charging of lead gel/dryfit, AGM/fleece or acid/wet batteries as well as LiFePO4 batteries Standard protection against overload, overcharging, overheating, reverse polarity and reverse battery discharge Charging cable compensation: voltage losses on the charging cables are automatically compensated for MPP charging current increase of 10% to 30% compared to conventional controllers thanks to the use of state-of-the-art controller technology (microprocessor). The increase in performance is particularly noticeable in the cooler months of the year and, for example, during high fog, low and diffuse lighting (wintering). Switchable charging characteristics for optimum charging of lead-gel/dryfit, AGM/fleece or acid/wet batteries as well as LiFePO4 batteries. The charging voltage is free of peaks and regulated in such a way that the batteries cannot be overcharged. Monitoring-free charging: Standard protection against overload, overheating, reverse polarity and battery back-discharge (if solar power is too low, e.g. at dusk, at night, etc.). Parallel/buffer operation: Compliance with charging regulations even with simultaneous operation of consumers. Overcharge protection: Regulates the charging current of the battery back if there is too much solar power and the battery is full, ensures that the battery is charged to the highest possible level by immediately recharging when power is consumed. IU1oU2" charging characteristic: Defined charging voltage increase (U1) prevents harmful acid stratification (lead) and ensures equalization charging of the individual battery cells (lead and lithium), followed by automatic trickle charging (U2). Charging cable compensation: Voltage losses on the charging cables are automatically compensated for. On-board network filter: Problem-free parallel operation with wind and motor generators, mains chargers, alternators, etc. Simple integration into the vehicle network Tested quality Certificates: CE, ROHS VOLTIMA MPPT solar charge controllers have the CE mark. 2-year warranty on all VOLTIMA MPPT solar charge controllers. MPPT: Ultra-fast maximum power point tracking By continuously monitoring the voltage and current output of the solar (PV) modules, MPPT technology ensures that all available energy is drawn from the photovoltaic modules and stored. The benefit of this is most noticeable when the sky is partly cloudy and the light intensity is constantly changing. VOLTIMA MPPT charge controllers comply with the latest safety standards. VOLTIMA charge controllers are CE approved. Quality components The VOLTIMA SCD12 MPPT solar charge controller Dual 12V 165Wp 50V 12A is very robustly built, but thanks to its active fan cooling it is also extremely efficient and whisper-quiet, making it suitable for continuous operation in motorhomes. Thanks to high-quality electronic components and the latest high-frequency switching controller technology, the solar charge controller is able to achieve high levels of efficiency with minimal power consumption. In addition to active fan cooling, the sturdy, ribbed and lightweight aluminum housing ensures maximum passive cooling and therefore quiet continuous operation. Overload/overheating protection MPPT solar charge controller Thanks to the many integrated protective circuits, durable electronics and intelligent microprocessor control, the VOLTIMA SCD12 MPPT solar charge controller Dual 12V 165Wp 50V 12A guarantees reliable operation. The MPPT solar charge controller is electronically protected twice against overload and protects itself against adverse installation conditions (e.g. poor ventilation, excessively high ambient temperatures) by gradually reducing the charging power. The VOLTIMA SCD12 MPPT solar charge controller Dual 12V 165Wp 50V 12A was built in accordance with the applicable safety guidelines It may only be used For charging lead-gel/AGM/acid batteries or LiFePO4 complete batteries (with integrated BMS, balancing, safety circuitry and approval!) of the specified nominal voltages and the co-supply of consumers connected to these batteries in permanently installed systems with the specified battery capacities and charging programs. Only solar panels up to the maximum power rating (WP) of the MPPT solar charge controller used. Only with solar panels below the maximum permissible voltage (VOC). With the specified cable cross-sections at the charging outputs and at the panel input. With fuses of the specified ratings near the battery to protect the cabling between the battery and charging outputs. In a well-ventilated room, protected against rain, moisture, dust and aggressive battery gases and in a non-condensing environment. In perfect technical condition. Only solar modules and no other power sources may be connected to the plus and minus input terminals for the solar panel. VOLTIMA MPPT solar charge controller Areas of application: Suitable for: Wet batteries (lead-acid batteries) AGM batteries (VRLA) GEL batteries (VRLA) Lithium-ion batteries (LiFePO4) Areas of application: Motorhome Camping bus - Camping van caravan Marine - Boat caravan Garden house Mountain hut Scope of delivery: VOLTIMA SCD12 MPPT solar charge controller Dual 12V 165Wp 50V 12A Instruction manual with technical data and fault diagnosis (English/German) 2 year warranty MPPT charge controller accessories: With the VOLTIMA solar charge controller monitor VSM1 you can remotely control your VOLTIMA SCD12 MPPT solar charge controller Dual 12V 165Wp 50V 12A thanks to the supplied connection cable.

VOLTIMA SCD12 MPPT solar charge controller Dual 12V 165Wp 50V 12A High efficiency and safety. The VOLTIMA MPPT solar charge controller for motorhomes, caravans, camper vans and the marine sector. A solar charger is supplied with energy via solar modules and then stores it in batteries. Using the latest and fastest technology, the VOLTIMA SCD12 MPPT Solar Charge Controller Dual 12V 165Wp 50V 12A maximizes this energy production and intelligently directs it to fully charge the batteries in as short a time as possible. The MPPT charge controllers from VOLTIMA maintain the functionality of the battery and thus extend its service life. VOLTIMA MPPT solar charge controllers with "IU1oU2" charging characteristic are connected as a link between the solar panel(s) and the battery(ies). With MPPT technology, the controller automatically determines the maximum power output (MPP) of the solar modules several times per second. It then transforms the excess voltage of the solar module into a higher charging current for the battery (realized by high-frequency switching controller technology with high efficiency). This additional charging current ensures shorter charging times and the best possible power utilization of the solar system. The VOLTIMA MPPT solar charge controllers operate fully automatically, are maintenance-free and offer the following functions: Two battery charging outputs: For main supply on-board battery as well as backup charging and charge retention of the starter battery Switchable charging characteristics for optimum charging of lead gel/dryfit, AGM/fleece or acid/wet batteries as well as LiFePO4 batteries Standard protection against overload, overcharging, overheating, reverse polarity and reverse battery discharge Charging cable compensation: voltage losses on the charging cables are automatically compensated for MPP charging current increase of 10% to 30% compared to conventional controllers thanks to the use of state-of-the-art controller technology (microprocessor). The increase in performance is particularly noticeable in the cooler months of the year and, for example, during high fog, low and diffuse lighting (wintering). Switchable charging characteristics for optimum charging of lead-gel/dryfit, AGM/fleece or acid/wet batteries as well as LiFePO4 batteries. The charging voltage is free of peaks and regulated in such a way that the batteries cannot be overcharged. Monitoring-free charging: Standard protection against overload, overheating, reverse polarity and battery back-discharge (if solar power is too low, e.g. at dusk, at night, etc.). Parallel/buffer operation: Compliance with charging regulations even with simultaneous operation of consumers. Overcharge protection: Regulates the charging current of the battery back if there is too much solar power and the battery is full, ensures that the battery is charged to the highest possible level by immediately recharging when power is consumed. IU1oU2" charging characteristic: Defined charging voltage increase (U1) prevents harmful acid stratification (lead) and ensures equalization charging of the individual battery cells (lead and lithium), followed by automatic trickle charging (U2). Charging cable compensation: Voltage losses on the charging cables are automatically compensated for. On-board network filter: Problem-free parallel operation with wind and motor generators, mains chargers, alternators, etc. Simple integration into the vehicle network Tested quality Certificates: CE, ROHS VOLTIMA MPPT solar charge controllers have the CE mark. 2-year warranty on all VOLTIMA MPPT solar charge controllers. MPPT: Ultra-fast maximum power point tracking By continuously monitoring the voltage and current output of the solar (PV) modules, MPPT technology ensures that all available energy is drawn from the photovoltaic modules and stored. The benefit of this is most noticeable when the sky is partly cloudy and the light intensity is constantly changing. VOLTIMA MPPT charge controllers comply with the latest safety standards. VOLTIMA charge controllers are CE approved. Quality components The VOLTIMA SCD12 MPPT solar charge controller Dual 12V 165Wp 50V 12A is very robustly built, but thanks to its active fan cooling it is also extremely efficient and whisper-quiet, making it suitable for continuous operation in motorhomes. Thanks to high-quality electronic components and the latest high-frequency switching controller technology, the solar charge controller is able to achieve high levels of efficiency with minimal power consumption. In addition to active fan cooling, the sturdy, ribbed and lightweight aluminum housing ensures maximum passive cooling and therefore quiet continuous operation. Overload/overheating protection MPPT solar charge controller Thanks to the many integrated protective circuits, durable electronics and intelligent microprocessor control, the VOLTIMA SCD12 MPPT solar charge controller Dual 12V 165Wp 50V 12A guarantees reliable operation. The MPPT solar charge controller is electronically protected twice against overload and protects itself against adverse installation conditions (e.g. poor ventilation, excessively high ambient temperatures) by gradually reducing the charging power. The VOLTIMA SCD12 MPPT solar charge controller Dual 12V 165Wp 50V 12A was built in accordance with the applicable safety guidelines It may only be used For charging lead-gel/AGM/acid batteries or LiFePO4 complete batteries (with integrated BMS, balancing, safety circuitry and approval!) of the specified nominal voltages and the co-supply of consumers connected to these batteries in permanently installed systems with the specified battery capacities and charging programs. Only solar panels up to the maximum power rating (WP) of the MPPT solar charge controller used. Only with solar panels below the maximum permissible voltage (VOC). With the specified cable cross-sections at the charging outputs and at the panel input. With fuses of the specified ratings near the battery to protect the cabling between the battery and charging outputs. In a well-ventilated room, protected against rain, moisture, dust and aggressive battery gases and in a non-condensing environment. In perfect technical condition. Only solar modules and no other power sources may be connected to the plus and minus input terminals for the solar panel. VOLTIMA MPPT solar charge controller Areas of application: Suitable for: Wet batteries (lead-acid batteries) AGM batteries (VRLA) GEL batteries (VRLA) Lithium-ion batteries (LiFePO4) Areas of application: Motorhome Camping bus - Camping van caravan Marine - Boat caravan Garden house Mountain hut Scope of delivery: VOLTIMA SCD12 MPPT solar charge controller Dual 12V 165Wp 50V 12A Instruction manual with technical data and fault diagnosis (English/German) 2 year warranty MPPT charge controller accessories: With the VOLTIMA solar charge controller monitor NSM1 you can remotely control your VOLTIMA SCD12 MPPT solar charge controller Dual 12V 165Wp 50V 12A thanks to the supplied connection cable.

NOQON SCD12 MPPT solar charge controller Dual 12V 165Wp 50V 12A High efficiency and safety. The NOQON MPPT solar charge controller for motorhomes, caravans, camper vans and the marine sector. A solar charger is supplied with energy via solar modules and then stores it in batteries. Using the latest and fastest technology, the NOQON SCD12 MPPT Solar Charge Controller Dual 12V 165Wp 50V 12A maximizes this energy production and intelligently directs it to fully charge the batteries in as short a time as possible. The MPPT charge controllers from NOQON maintain the functionality of the battery and thus extend its service life. NOQON MPPT solar charge controllers with "IU1oU2" charging characteristic are connected as a link between the solar panel(s) and the battery(ies). With MPPT technology, the controller automatically determines the maximum power output (MPP) of the solar modules several times per second. It then transforms the excess voltage of the solar module into a higher charging current for the battery (realized by high-frequency switching controller technology with high efficiency). This additional charging current ensures shorter charging times and the best possible power utilization of the solar system. The NOQON MPPT solar charge controllers operate fully automatically, are maintenance-free and offer the following functions: Two battery charging outputs: For main supply on-board battery as well as backup charging and charge retention of the starter battery Switchable charging characteristics for optimum charging of lead gel/dryfit, AGM/fleece or acid/wet batteries as well as LiFePO4 batteries Standard protection against overload, overcharging, overheating, reverse polarity and reverse battery discharge Charging cable compensation: voltage losses on the charging cables are automatically compensated for MPP charging current increase of 10% to 30% compared to conventional controllers thanks to the use of state-of-the-art controller technology (microprocessor). The increase in performance is particularly noticeable in the cooler months of the year and, for example, during high fog, low and diffuse lighting (wintering). Switchable charging characteristics for optimum charging of lead-gel/dryfit, AGM/fleece or acid/wet batteries as well as LiFePO4 batteries. The charging voltage is free of peaks and regulated in such a way that the batteries cannot be overcharged. Monitoring-free charging: Standard protection against overload, overheating, reverse polarity and battery back-discharge (if solar power is too low, e.g. at dusk, at night, etc.). Parallel/buffer operation: Compliance with charging regulations even with simultaneous operation of consumers. Overcharge protection: Regulates the charging current of the battery back if there is too much solar power and the battery is full, ensures that the battery is charged to the highest possible level by immediately recharging when power is consumed. IU1oU2" charging characteristic: Defined charging voltage increase (U1) prevents harmful acid stratification (lead) and ensures equalization charging of the individual battery cells (lead and lithium), followed by automatic trickle charging (U2). Charging cable compensation: Voltage losses on the charging cables are automatically compensated for. On-board network filter: Problem-free parallel operation with wind and motor generators, mains chargers, alternators, etc. Simple integration into the vehicle network Tested quality Certificates: CE, ROHS NOQON MPPT solar charge controllers have the CE mark. 2-year warranty on all NOQON MPPT solar charge controllers. MPPT: Ultra-fast maximum power point tracking By continuously monitoring the voltage and current output of the solar (PV) modules, MPPT technology ensures that all available energy is drawn from the photovoltaic modules and stored. The benefit of this is most noticeable when the sky is partly cloudy and the light intensity is constantly changing. NOQON MPPT charge controllers comply with the latest safety standards. NOQON charge controllers are CE approved. Quality components The NOQON SCD12 MPPT solar charge controller Dual 12V 165Wp 50V 12A is very robustly built, but thanks to its active fan cooling it is also extremely efficient and whisper-quiet, making it suitable for continuous operation in motorhomes. Thanks to high-quality electronic components and the latest high-frequency switching controller technology, the solar charge controller is able to achieve high levels of efficiency with minimal power consumption. In addition to active fan cooling, the sturdy, ribbed and lightweight aluminum housing ensures maximum passive cooling and therefore quiet continuous operation. Overload/overheating protection MPPT solar charge controller Thanks to the many integrated protective circuits, durable electronics and intelligent microprocessor control, the VOLTIMA SCD12 MPPT solar charge controller Dual 12V 165Wp 50V 12A guarantees reliable operation. The MPPT solar charge controller is electronically protected twice against overload and protects itself against adverse installation conditions (e.g. poor ventilation, excessively high ambient temperatures) by gradually reducing the charging power. The NOQON SCD12 MPPT solar charge controller Dual 12V 165Wp 50V 12A was built in accordance with the applicable safety guidelines It may only be used For charging lead-gel/AGM/acid batteries or LiFePO4 complete batteries (with integrated BMS, balancing, safety circuitry and approval!) of the specified nominal voltages and the co-supply of consumers connected to these batteries in permanently installed systems with the specified battery capacities and charging programs. Only solar panels up to the maximum power rating (WP) of the MPPT solar charge controller used. Only with solar panels below the maximum permissible voltage (VOC). With the specified cable cross-sections at the charging outputs and at the panel input. With fuses of the specified ratings near the battery to protect the cabling between the battery and charging outputs. In a well-ventilated room, protected against rain, moisture, dust and aggressive battery gases and in a non-condensing environment. In perfect technical condition. Only solar modules and no other power sources may be connected to the plus and minus input terminals for the solar panel. VOLTIMA MPPT solar charge controller Areas of application: Suitable for: Wet batteries (lead-acid batteries) AGM batteries (VRLA) GEL batteries (VRLA) Lithium-ion batteries (LiFePO4) Areas of application: Motorhome Camping bus - Camping van caravan Marine - Boat caravan Garden house Mountain hut Scope of delivery: VOLTIMA SCD12 MPPT solar charge controller Dual 12V 165Wp 50V 12A Instruction manual with technical data and fault diagnosis (English/German) 2 year warranty MPPT charge controller accessories: With the NOQON solar charge controller monitor NSM1 you can remotely control your NOQON SCD12 MPPT solar charge controller Dual 12V 165Wp 50V 12A thanks to the supplied connection cable.

NOQON SCN40 MPPT solar charge controller 12V/24V 480Wp/960Wp 50V 40A High efficiency and safety. The NOQON MPPT solar charge controller for motorhomes, caravans, camper vans and the marine sector. A solar charger is supplied with energy via solar modules and then stores it in batteries. Using the latest and fastest technology, the NOQON SCN40 MPPT solar charge controller 12V/24V 480Wp/960Wp 50V 40A maximizes this energy production and intelligently directs it to fully charge the batteries in as short a time as possible. The MPPT charge controllers from NOQON maintain the functionality of the battery and thus extend its service life. NOQON MPPT solar charge controllers with "IU1oU2" charging characteristic are connected as a link between the solar panel(s) and the battery(ies). With MPPT technology, the controller automatically determines the maximum power output (MPP) of the solar modules several times per second. It then transforms the excess voltage of the solar module into a higher charging current for the battery (realized by high-frequency switching controller technology with high efficiency). This additional charging current ensures shorter charging times and the best possible power utilization of the solar system. The NOQON MPPT solar charge controllers operate fully automatically, are maintenance-free and offer the following functions: Parallel/buffer operation: compliance with charging regulations even with simultaneous operation of consumers Switchable charging characteristics for optimum charging of lead-gel/dryfit, AGM/fleece or acid/wet batteries as well as LiFePO4 batteries Standard protection against overload, overcharging, overheating, reverse polarity and reverse battery discharge Charging cable compensation: voltage losses on the charging cables are automatically compensated for MPP charging current increase of 10% to 30% compared to conventional controllers thanks to the use of state-of-the-art controller technology (microprocessor). The increase in performance is particularly noticeable in the cooler months of the year and, for example, during high fog, low and diffuse lighting (wintering). Switchable charging characteristics for optimum charging of lead-gel/dryfit, AGM/fleece or acid/wet batteries as well as LiFePO4 batteries. The charging voltage is free of peaks and regulated in such a way that the batteries cannot be overcharged. Monitoring-free charging: Standard protection against overload, overheating, reverse polarity and battery back-discharge (if solar power is too low, e.g. at dusk, at night, etc.). Parallel/buffer operation: Compliance with charging regulations even with simultaneous operation of consumers. Overcharge protection: Regulates the charging current of the battery back if there is too much solar power and the battery is full, ensures that the battery is charged to the highest possible level by immediately recharging when power is consumed. IU1oU2" charging characteristic: Defined charging voltage increase (U1) prevents harmful acid stratification (lead) and ensures equalization charging of the individual battery cells (lead and lithium), followed by automatic trickle charging (U2). Charging cable compensation: Voltage losses on the charging cables are automatically compensated for. On-board network filter: Problem-free parallel operation with wind and motor generators, mains chargers, alternators, etc. Simple integration into the vehicle network Tested quality Certificates: CE, ROHS NOQON MPPT solar charge controllers have the CE mark. 2-year warranty on all NOQON MPPT solar charge controllers. MPPT: Ultra-fast maximum power point tracking By continuously monitoring the voltage and current output of the solar (PV) modules, MPPT technology ensures that all available energy is drawn from the photovoltaic modules and stored. The benefit of this is most noticeable when the sky is partly cloudy and the light intensity is constantly changing. NOQON MPPT charge controllers comply with the latest safety standards. NOQON charge controllers are CE approved. Quality components The NOQON SCN40 MPPT solar charge controller 12V/24V 480Wp/960Wp 50V 40A is very robustly built, but thanks to its active fan cooling it is also whisper-quiet and extremely efficient, making it suitable for continuous operation in motorhomes. Thanks to high-quality electronic components and the latest high-frequency switching controller technology, the solar charge controller is able to achieve high levels of efficiency with minimal power consumption. In addition to active fan cooling, the sturdy, ribbed and lightweight aluminum housing ensures maximum passive cooling and therefore quiet continuous operation. Overload/overheating protection MPPT solar charge controller Thanks to the many integrated protective circuits, durable electronics and intelligent microprocessor control, the NOQON SCN40 MPPT solar charge controller 12V/24V 480Wp/960Wp 50V 40A guarantees reliable operation. The MPPT solar charge controller has double electronic protection against overload and protects itself against adverse installation conditions (e.g. poor ventilation, excessive ambient temperatures) by gradually reducing the charging power. The NOQON SCN40 MPPT solar charge controller 12V/24V 480Wp/960Wp 50V 40A was built in accordance with the applicable safety guidelines It may only be used For charging lead-gel/AGM/acid batteries or LiFePO4 complete batteries (with integrated BMS, balancing, safety circuitry and approval!) of the specified nominal voltages and the co-supply of consumers connected to these batteries in permanently installed systems with the specified battery capacities and charging programs. Only solar panels up to the maximum power rating (WP) of the MPPT solar charge controller used. Only with solar panels below the maximum permissible voltage (VOC). With the specified cable cross-sections at the charging outputs and at the panel input. With fuses of the specified ratings near the battery to protect the cabling between the battery and charging outputs. In a well-ventilated room, protected against rain, moisture, dust and aggressive battery gases and in a non-condensing environment. In perfect technical condition. Only solar modules and no other power sources may be connected to the plus and minus input terminals for the solar panel. NOQON MPPT solar charge controller Areas of application: Suitable for: Wet batteries (lead-acid batteries) AGM batteries (VRLA) GEL batteries (VRLA) Lithium-ion batteries (LiFePO4) Areas of application: Motorhome Camping bus - Camping van caravan Marine - Boat caravan Garden house Mountain hut Scope of delivery: NOQON SCN40 MPPT solar charge controller 12V/24V 480Wp/960Wp 50V 40A Instruction manual with technical data and fault diagnosis (English/German) 2 year warranty MPPT charge controller accessories: With the NOQON solar charge controller monitor NSM1 you can remotely control your NOQON SCN40 MPPT solar charge controller 12V/24V 480Wp/960Wp 50V 40A thanks to the supplied connection cable.

NOQON SCN40 MPPT solar charge controller 12V/24V 480Wp/960Wp 50V 40A High efficiency and safety. The NOQON MPPT solar charge controller for motorhomes, caravans, camper vans and the marine sector. A solar charger is supplied with energy via solar modules and then stores it in batteries. Using the latest and fastest technology, the NOQON SCN40 MPPT solar charge controller 12V/24V 480Wp/960Wp 50V 40A maximizes this energy production and intelligently directs it to fully charge the batteries in as short a time as possible. The MPPT charge controllers from NOQON maintain the functionality of the battery and thus extend its service life. NOQON MPPT solar charge controllers with "IU1oU2" charging characteristic are connected as a link between the solar panel(s) and the battery(ies). With MPPT technology, the controller automatically determines the maximum power output (MPP) of the solar modules several times per second. It then transforms the excess voltage of the solar module into a higher charging current for the battery (realized by high-frequency switching controller technology with high efficiency). This additional charging current ensures shorter charging times and the best possible power utilization of the solar system. The NOQON MPPT solar charge controllers operate fully automatically, are maintenance-free and offer the following functions: Parallel/buffer operation: compliance with charging regulations even with simultaneous operation of consumers Switchable charging characteristics for optimum charging of lead-gel/dryfit, AGM/fleece or acid/wet batteries as well as LiFePO4 batteries Standard protection against overload, overcharging, overheating, reverse polarity and reverse battery discharge Charging cable compensation: voltage losses on the charging cables are automatically compensated for MPP charging current increase of 10% to 30% compared to conventional controllers thanks to the use of state-of-the-art controller technology (microprocessor). The increase in performance is particularly noticeable in the cooler months of the year and, for example, during high fog, low and diffuse lighting (wintering). Switchable charging characteristics for optimum charging of lead-gel/dryfit, AGM/fleece or acid/wet batteries as well as LiFePO4 batteries. The charging voltage is free of peaks and regulated in such a way that the batteries cannot be overcharged. Monitoring-free charging: Standard protection against overload, overheating, reverse polarity and battery back-discharge (if solar power is too low, e.g. at dusk, at night, etc.). Parallel/buffer operation: Compliance with charging regulations even with simultaneous operation of consumers. Overcharge protection: Regulates the charging current of the battery back if there is too much solar power and the battery is full, ensures that the battery is charged to the highest possible level by immediately recharging when power is consumed. IU1oU2" charging characteristic: Defined charging voltage increase (U1) prevents harmful acid stratification (lead) and ensures equalization charging of the individual battery cells (lead and lithium), followed by automatic trickle charging (U2). Charging cable compensation: Voltage losses on the charging cables are automatically compensated for. On-board network filter: Problem-free parallel operation with wind and motor generators, mains chargers, alternators, etc. Simple integration into the vehicle network Tested quality Certificates: CE, ROHS NOQON MPPT solar charge controllers have the CE mark. 2-year warranty on all NOQON MPPT solar charge controllers. MPPT: Ultra-fast maximum power point tracking By continuously monitoring the voltage and current output of the solar (PV) modules, MPPT technology ensures that all available energy is drawn from the photovoltaic modules and stored. The benefit of this is most noticeable when the sky is partly cloudy and the light intensity is constantly changing. NOQON MPPT charge controllers comply with the latest safety standards. NOQON charge controllers are CE approved. Quality components The NOQON SCN40 MPPT solar charge controller 12V/24V 480Wp/960Wp 50V 40A is very robustly built, but thanks to its active fan cooling it is also whisper-quiet and extremely efficient, making it suitable for continuous operation in motorhomes. Thanks to high-quality electronic components and the latest high-frequency switching controller technology, the solar charge controller is able to achieve high levels of efficiency with minimal power consumption. In addition to active fan cooling, the sturdy, ribbed and lightweight aluminum housing ensures maximum passive cooling and therefore quiet continuous operation. Overload/overheating protection MPPT solar charge controller Thanks to the many integrated protective circuits, durable electronics and intelligent microprocessor control, the NOQON SCN40 MPPT solar charge controller 12V/24V 480Wp/960Wp 50V 40A guarantees reliable operation. The MPPT solar charge controller has double electronic protection against overload and protects itself against adverse installation conditions (e.g. poor ventilation, excessive ambient temperatures) by gradually reducing the charging power. The NOQON SCN40 MPPT solar charge controller 12V/24V 480Wp/960Wp 50V 40A was built in accordance with the applicable safety guidelines It may only be used For charging lead-gel/AGM/acid batteries or LiFePO4 complete batteries (with integrated BMS, balancing, safety circuitry and approval!) of the specified nominal voltages and the co-supply of consumers connected to these batteries in permanently installed systems with the specified battery capacities and charging programs. Only solar panels up to the maximum power rating (WP) of the MPPT solar charge controller used. Only with solar panels below the maximum permissible voltage (VOC). With the specified cable cross-sections at the charging outputs and at the panel input. With fuses of the specified ratings near the battery to protect the cabling between the battery and charging outputs. In a well-ventilated room, protected against rain, moisture, dust and aggressive battery gases and in a non-condensing environment. In perfect technical condition. Only solar modules and no other power sources may be connected to the plus and minus input terminals for the solar panel. NOQON MPPT solar charge controller Areas of application: Suitable for: Wet batteries (lead-acid batteries) AGM batteries (VRLA) GEL batteries (VRLA) Lithium-ion batteries (LiFePO4) Areas of application: Motorhome Camping bus - Camping van caravan Marine - Boat caravan Garden house Mountain hut Scope of delivery: NOQON SCN40 MPPT solar charge controller 12V/24V 480Wp/960Wp 50V 40A Instruction manual with technical data and fault diagnosis (English/German) 2 year warranty MPPT charge controller accessories: With the NOQON solar charge controller monitor NSM1 you can remotely control your NOQON SCN40 MPPT solar charge controller 12V/24V 480Wp/960Wp 50V 40A thanks to the supplied connection cable.

NOQON SCN20 MPPT solar charge controller 12V/24V 240Wp/480Wp 50V 20A High efficiency and safety. The NOQON MPPT solar charge controller for motorhomes, caravans, camper vans and the marine sector. A solar charger is supplied with energy via solar modules and then stores it in batteries. Using the latest and fastest technology, the NOQON SCN20 MPPT solar charge controller 12V/24V 240Wp/480Wp 50V 20A maximizes this energy production and intelligently directs it to fully charge the batteries in as short a time as possible. The MPPT charge controllers from NOQON maintain the functionality of the battery and thus extend its service life. NOQON MPPT solar charge controllers with "IU1oU2" charging characteristic are connected as a link between the solar panel(s) and the battery(ies). With MPPT technology, the controller automatically determines the maximum power output (MPP) of the solar modules several times per second. It then transforms the excess voltage of the solar module into a higher charging current for the battery (realized by high-frequency switching controller technology with high efficiency). This additional charging current ensures shorter charging times and the best possible power utilization of the solar system. The NOQON MPPT solar charge controllers operate fully automatically, are maintenance-free and offer the following functions: Parallel/buffer operation: compliance with charging regulations even when consumers are operating at the same time Switchable charging characteristics for optimum charging of lead-gel/dryfit, AGM/fleece or acid/wet batteries as well as LiFePO4 batteries Standard protection against overload, overcharging, overheating, reverse polarity and reverse battery discharge Charging cable compensation: voltage losses on the charging cables are automatically compensated for MPP charging current increase of 10% to 30% compared to conventional controllers thanks to the use of state-of-the-art controller technology (microprocessor). The increase in performance is particularly noticeable in the cooler months of the year and, for example, during high fog, low and diffuse lighting (wintering). Switchable charging characteristics for optimum charging of lead-gel/dryfit, AGM/fleece or acid/wet batteries as well as LiFePO4 batteries. The charging voltage is free of peaks and regulated in such a way that the batteries cannot be overcharged. Monitoring-free charging: Standard protection against overload, overheating, reverse polarity and battery back-discharge (if solar power is too low, e.g. at dusk, at night, etc.). Parallel/buffer operation: Compliance with charging regulations even with simultaneous operation of consumers. Overcharge protection: Regulates the charging current of the battery back if there is too much solar power and the battery is full, ensures that the battery is charged to the highest possible level by immediately recharging when power is consumed. IU1oU2" charging characteristic: Defined charging voltage increase (U1) prevents harmful acid stratification (lead) and ensures equalization charging of the individual battery cells (lead and lithium), followed by automatic trickle charging (U2). Charging cable compensation: Voltage losses on the charging cables are automatically compensated for. On-board network filter: Problem-free parallel operation with wind and motor generators, mains chargers, alternators, etc. Simple integration into the vehicle network Tested quality Certificates: CE, ROHS NOQON MPPT solar charge controllers have the CE mark. 2-year warranty on all NOQON MPPT solar charge controllers. MPPT: Ultra-fast maximum power point tracking By continuously monitoring the voltage and current output of the solar (PV) modules, MPPT technology ensures that all available energy is drawn from the photovoltaic modules and stored. The benefit of this is most noticeable when the sky is partly cloudy and the light intensity is constantly changing. NOQON MPPT charge controllers comply with the latest safety standards. NOQON charge controllers are CE approved. Quality components The NOQON SCN20 MPPT solar charge controller 12V/24V 240Wp/480Wp 50V 20A has a very robust design, but thanks to its active fan cooling it is also extremely efficient and whisper-quiet, making it suitable for continuous operation in motorhomes. Thanks to high-quality electronic components and the latest high-frequency switching controller technology, the solar charge controller is able to achieve high levels of efficiency with minimal power consumption. In addition to active fan cooling, the sturdy, ribbed and lightweight aluminum housing ensures maximum passive cooling and therefore quiet continuous operation. Overload/overheating protection MPPT solar charge controller Thanks to the many integrated protective circuits, durable electronics and intelligent microprocessor control, the NOQON SCN20 MPPT solar charge controller 12V/24V 240Wp/480Wp 50V 20A guarantees reliable operation. The MPPT solar charge controller has double electronic protection against overload and protects itself against adverse installation conditions (e.g. poor ventilation, excessive ambient temperatures) by gradually reducing the charging power. The NOQON SCN20 MPPT solar charge controller 12V/24V 240Wp/480Wp 50V 20A was built in accordance with the applicable safety guidelines It may only be used For charging lead-gel/AGM/acid batteries or LiFePO4 complete batteries (with integrated BMS, balancing, safety circuitry and approval!) of the specified nominal voltages and the co-supply of consumers connected to these batteries in permanently installed systems with the specified battery capacities and charging programs. Only solar panels up to the maximum power rating (WP) of the MPPT solar charge controller used. Only with solar panels below the maximum permissible voltage (VOC). With the specified cable cross-sections at the charging outputs and at the panel input. With fuses of the specified ratings near the battery to protect the cabling between the battery and charging outputs. In a well-ventilated room, protected against rain, moisture, dust and aggressive battery gases and in a non-condensing environment. In perfect technical condition. Only solar modules and no other power sources may be connected to the plus and minus input terminals for the solar panel. NOQON MPPT solar charge controller Areas of application: Suitable for: Wet batteries (lead-acid batteries) AGM batteries (VRLA) GEL batteries (VRLA) Lithium-ion batteries (LiFePO4) Areas of application: Motorhome Camping bus - Camping van caravan Marine - Boat caravan Garden house Mountain hut Scope of delivery: NOQON SCN20 MPPT solar charge controller 12V/24V 240Wp/480Wp 50V 20A Instruction manual with technical data and fault diagnosis (English/German) 2 year warranty MPPT charge controller accessories: With the NOQON NSM1 solar charge controller monitor, you can remotely control your NOQON SCN20 MPPT solar charge controller 12V/24V 240Wp/480Wp 50V 20A using the supplied connection cable.

NOQON SCN20 MPPT solar charge controller 12V/24V 240Wp/480Wp 50V 20A High efficiency and safety. The NOQON MPPT solar charge controller for motorhomes, caravans, camper vans and the marine sector. A solar charger is supplied with energy via solar modules and then stores it in batteries. Using the latest and fastest technology, the NOQON SCN20 MPPT solar charge controller 12V/24V 240Wp/480Wp 50V 20A maximizes this energy production and intelligently directs it to fully charge the batteries in as short a time as possible. The MPPT charge controllers from NOQON maintain the functionality of the battery and thus extend its service life. NOQON MPPT solar charge controllers with "IU1oU2" charging characteristic are connected as a link between the solar panel(s) and the battery(ies). With MPPT technology, the controller automatically determines the maximum power output (MPP) of the solar modules several times per second. It then transforms the excess voltage of the solar module into a higher charging current for the battery (realized by high-frequency switching controller technology with high efficiency). This additional charging current ensures shorter charging times and the best possible power utilization of the solar system. The NOQON MPPT solar charge controllers operate fully automatically, are maintenance-free and offer the following functions: Parallel/buffer operation: compliance with charging regulations even when consumers are operating at the same time Switchable charging characteristics for optimum charging of lead-gel/dryfit, AGM/fleece or acid/wet batteries as well as LiFePO4 batteries Standard protection against overload, overcharging, overheating, reverse polarity and reverse battery discharge Charging cable compensation: voltage losses on the charging cables are automatically compensated for MPP charging current increase of 10% to 30% compared to conventional controllers thanks to the use of state-of-the-art controller technology (microprocessor). The increase in performance is particularly noticeable in the cooler months of the year and, for example, during high fog, low and diffuse lighting (wintering). Switchable charging characteristics for optimum charging of lead-gel/dryfit, AGM/fleece or acid/wet batteries as well as LiFePO4 batteries. The charging voltage is free of peaks and regulated in such a way that the batteries cannot be overcharged. Monitoring-free charging: Standard protection against overload, overheating, reverse polarity and battery back-discharge (if solar power is too low, e.g. at dusk, at night, etc.). Parallel/buffer operation: Compliance with charging regulations even with simultaneous operation of consumers. Overcharge protection: Regulates the charging current of the battery back if there is too much solar power and the battery is full, ensures that the battery is charged to the highest possible level by immediately recharging when power is consumed. IU1oU2" charging characteristic: Defined charging voltage increase (U1) prevents harmful acid stratification (lead) and ensures equalization charging of the individual battery cells (lead and lithium), followed by automatic trickle charging (U2). Charging cable compensation: Voltage losses on the charging cables are automatically compensated for. On-board network filter: Problem-free parallel operation with wind and motor generators, mains chargers, alternators, etc. Simple integration into the vehicle network Tested quality Certificates: CE, ROHS NOQON MPPT solar charge controllers have the CE mark. 2-year warranty on all NOQON MPPT solar charge controllers. MPPT: Ultra-fast maximum power point tracking By continuously monitoring the voltage and current output of the solar (PV) modules, MPPT technology ensures that all available energy is drawn from the photovoltaic modules and stored. The benefit of this is most noticeable when the sky is partly cloudy and the light intensity is constantly changing. NOQON MPPT charge controllers comply with the latest safety standards. NOQON charge controllers are CE approved. Quality components The NOQON SCN20 MPPT solar charge controller 12V/24V 240Wp/480Wp 50V 20A has a very robust design, but thanks to its active fan cooling it is also extremely efficient and whisper-quiet, making it suitable for continuous operation in motorhomes. Thanks to high-quality electronic components and the latest high-frequency switching controller technology, the solar charge controller is able to achieve high levels of efficiency with minimal power consumption. In addition to active fan cooling, the sturdy, ribbed and lightweight aluminum housing ensures maximum passive cooling and therefore quiet continuous operation. Overload/overheating protection MPPT solar charge controller Thanks to the many integrated protective circuits, durable electronics and intelligent microprocessor control, the NOQON SCN20 MPPT solar charge controller 12V/24V 240Wp/480Wp 50V 20A guarantees reliable operation. The MPPT solar charge controller has double electronic protection against overload and protects itself against adverse installation conditions (e.g. poor ventilation, excessive ambient temperatures) by gradually reducing the charging power. The NOQON SCN20 MPPT solar charge controller 12V/24V 240Wp/480Wp 50V 20A was built in accordance with the applicable safety guidelines It may only be used For charging lead-gel/AGM/acid batteries or LiFePO4 complete batteries (with integrated BMS, balancing, safety circuitry and approval!) of the specified nominal voltages and the co-supply of consumers connected to these batteries in permanently installed systems with the specified battery capacities and charging programs. Only solar panels up to the maximum power rating (WP) of the MPPT solar charge controller used. Only with solar panels below the maximum permissible voltage (VOC). With the specified cable cross-sections at the charging outputs and at the panel input. With fuses of the specified ratings near the battery to protect the cabling between the battery and charging outputs. In a well-ventilated room, protected against rain, moisture, dust and aggressive battery gases and in a non-condensing environment. In perfect technical condition. Only solar modules and no other power sources may be connected to the plus and minus input terminals for the solar panel. NOQON MPPT solar charge controller Areas of application: Suitable for: Wet batteries (lead-acid batteries) AGM batteries (VRLA) GEL batteries (VRLA) Lithium-ion batteries (LiFePO4) Areas of application: Motorhome Camping bus - Camping van caravan Marine - Boat caravan Garden house Mountain hut Scope of delivery: NOQON SCN20 MPPT solar charge controller 12V/24V 240Wp/480Wp 50V 20A Instruction manual with technical data and fault diagnosis (English/German) 2 year warranty MPPT charge controller accessories: With the NOQON NSM1 solar charge controller monitor, you can remotely control your NOQON SCN20 MPPT solar charge controller 12V/24V 240Wp/480Wp 50V 20A using the supplied connection cable.

VOLTIMA HSZ100 Solar module bracket / mounting bracket Angle solar brackets for outdoor useAluminum construction for wall and roof mounting for framed solar modules with 30mm frame thickness up to 200W. Attach your solar modules conveniently to the garden shed in your allotment garden or to the roof of your mobile home if you have space problems. The set consists of 4 x Z-brackets with a side length of 100mm each. Matching 16x6mm stainless steel screws and wing nuts (incl. snap rings and washers) are included.Article features: Suitable for 30mm thick solar modules, up to 200W100mm Z-bracket Aluminum Easy handling For solar modules up to 150W Wall, roof and free-standing mounting incl. stainless steel fixing screws Versatile use Dimensions (LxWxH): 10 x 5 x 2.7 cm Manufacturer's guarantee: 20 years Simple installation, quick commissioning and prepared materials make your installation child's play!The brackets are specially designed for framed solar modules and are intended for outdoor use. Enjoy your freedom with quality products from VOLTIMA

VOLTIMA HSZ38 solar module bracket / mounting bracket Angle solar brackets for outdoor use Aluminum construction for wall and roof mounting for small framed solar modules with 30mm frame thickness up to 100W. Attach your solar modules conveniently to the garden shed in your allotment garden or to the roof of your mobile home if you have space problems. The set consists of 4 Z-brackets with a side length of 38mm each. Matching 16x6mm stainless steel screws and wing nuts (incl. snap rings and washers) are included.Article features: Suitable for 30mm thick solar modules, up to 100W38mm long Z-bracket made of aluminum Easy handling For solar modules up to 50W Wall, roof and free-standing mounting incl. stainless steel fixing screws Versatile use Dimensions (LxWxH): 3.8 x 5 x 2.7 cm Manufacturer's guarantee: 20 years Simple installation, quick commissioning and prepared materials make your installation child's play! The brackets are specially designed for framed solar modules and are intended for outdoor use. Enjoy your freedom with quality products from VOLTIMA

  Nutzen Sie die Kraft der Sonne auf Ihrem Balkon mit Solar Hook. Mit dem Montagepaket Stockschraube sichern Sie sich gerahmte Solarmodule auf Schrägdächern und Fassaden zuverlässig. Das Komplettset beinhaltet hochwertige Materialien wie Edelstahl und Aluminium. SOLAR-HOOK bietet robuste und langlebige Montagesysteme mit hoher Schneelastbeständigkeit. Schnelle Installation, Kostenersparnis und vielseitige Anwendungsmöglichkeiten machen sie zur optimalen Wahl. SOLAR-HOOK Montagepaket Stockschrauben Dieses Set ist speziell zur Montage von zwei Modulen auf Schrägdächern und Fassade, in die gebohrt werden kann und damit Ideal zur Montage eines für ein Balkonkraftwerks - Für Module von 380 - 430Wp- Für zwei Solarmodule mit einer Länge zwischen 1755 und 2094 mm geeignet.Zum besseren Verständnis, ob dieses Set für ihre Anwendung passt und wie es montiert wird, schauen Sie sich die Anleitungen (PDF-Dateien) im Download-Bereich an und oder dieses Video. Warum Solar-Hook ?Einfache und schnelle MontageHochwertige und langlebige KomponentenAlle benötigten Teile in einem SetEffiziente Installation von Solarmodulen  Einstellbarer Winkel Robustes und witterungsbeständiges Design.Breite, durchgehende Grundschienen für optimale Lastumlagerung und geringe Flächenpressung.  Häufig gestellte FragenWie stabil ist die Befestigung der Solarmodule mit dem Montagepaket Stockschrauben?Das Montagepaket Stockschrauben gewährleistet eine sichere Befestigung der gerahmten Solarmodule. Es sorgt für eine stabile Verbindung und ist so konzipiert, dass es verschiedenen Witterungsbedingungen standhält.Ist das Montagesystem wartungsarm?Ja, das Montagesystem erfordert nur minimale Wartung. Gelegentliche Inspektionen und Reinigungen der Solarmodule sind empfehlenswert, um eine optimale Leistung zu gewährleisten.Ist das Montagesystem mit verschiedenen Arten von Solarmodulen kompatibel?Ja, das Montagesystem ist mit den meisten gängigen Solarmodulen auf dem Markt kompatibel. Es kann an die spezifischen Anforderungen Ihres Solarmodulherstellers angepasst werden.Bietet das Montagesystem eine einstellbare Neigung der Solarmodule?Ja, unser Montagesystem ermöglicht die Einstellung der Neigung der Solarmodule, um eine optimale Sonneneinstrahlung und Energieerzeugung zu gewährleisten.   Montagesatz für 2 Module bestehend aus:6x Stockschraube M10 x 200 mit6x Adapterplatte zur Stockschraube6x Schloßschraube M10 x 25 inkl. Selbstsichernder Mutter4x Aluminiumprofil 40x40x1200mm2x Profilverbinder2x flexible Mittelklemme4x flexible Endklemme16x selbstschneidende Schraube St. 4,8x19 mm

Fine stranded wire made from bare copper wires Core insulation based on PVC You purchase: 1 meter of cable with a cross-section of your choice Colors red and black All ordered quantities are delivered in one piece. Product properties: Flame retardant according to IEC 60332-1-2 Technical data: Approvals: HD 21/VDE 0281 Insulation Specific volume resistance: > 20 GOhm x cm Conductor construction: Fine-stranded according to VDE 0295 Class 5/ IEC 60228 Class 5 Minimum bending radius: According to HD 516 at 20°C ±10°C cable temperature Rated voltage: U0/U: 450/750 V Test voltage: 2500 V Current carrying capacity: VDE 0298 Part 4 Temperature range: Permanently installed: -30°C to +80°C

Voltima solar connection adapter for 4-6mm² solar cable MC type 4 Protection class: mated IP67 Protection class: II Rated current: max. 30A System voltage: max. 1000V Locking system (snap in) Temperature range -40°C to 90 °C

Voltima solar connection adapter for 4-6mm² solar cable MC type 4 Protection class: mated IP67 Protection class: II Rated current: max. 30A System voltage: max. 1000V Locking system (snap in) Temperature range -40°C to 90 °C

Solar extension cable set 6mm2 - 2 x solar cable with MC4 plug and socket- double insulated made of halogen-free, cross-linked polyolefin- UV & ozone resistant- Available in 2m, 5m, 10m or 20m length

Solar extension cable set 6mm2 - 2 x solar cable with MC4 plug and socket- double insulated made of halogen-free, cross-linked polyolefin- UV & ozone resistant- Available in 2m, 5m, 10m or 20m length

Solar cable set 6mm²- 2 cables, each with an MC4 plug on one side for connection to the solar modules & open ends on the other side for connection to the solar charge controller- Double insulated from halogen-free, cross-linked polyolefin- UV & ozone resistant,- Available in 3m, 5m, 10m or 20m lengths

Solar cable set 6mm²- 2 cables, each with an MC4 plug on one side for connection to the solar modules & open ends on the other side for connection to the solar charge controller- Double insulated from halogen-free, cross-linked polyolefin- UV & ozone resistant,- Available in 3m, 5m, 10m or 20m lengths

This special connection is used for the assembly of parallel solar PV modules. Voltima Solar Y (L) connection adapter for 4-6mm² solar cable 2to1 MC type 4 enables time-saving, reliable cabling of solar panels and quick, easy installation.

This special connection is used for the assembly of parallel solar PV modules. Voltima Solar Y (L) connection adapter for 4-6mm² solar cable 2to1 MC type 4 enables time-saving, reliable cabling of solar panels and quick, easy installation.

Sturdy battery connection cable set. The cable is suitable for connecting a battery with M6, M8 or M10 round terminals to a device that has a screw terminal connection. This cable set can be used to connect batteries to devices such as solar charge controllers, inverters and battery chargers with a screw terminal connection. The cross-section and size of the cable lugs are freely selectable. Please refer to the device manufacturer's instructions for use to select the cable cross-section. Technical dataLength: 2m Scope of delivery: 1 x battery connection cable wire red 2m1 x battery connection cable wire black 2m