NOQON solar charge controller monitor NSM1The NOQON solar charge controller monitor NSM1 can be connected to an MPPT solar charge controller to display the following values: Charging current (A), solar battery voltage (V), solar power (W), solar electricity meter (Ah and WH)Suitable for the following solar charge controllers:- NOQON SCD12 MPPT solar charge controller Dual 12V 165Wp 50V 12A- NOQON SCD25 MPPT solar charge controller Dual 12V 350Wp 50V 25A- NOQON SCN20 MPPT solar charge controller 12V/24V 240Wp/480Wp 50V 20A- NOQON SCN40 MPPT solar charge controller 12V/24V 480Wp/960Wp 50V 40A

The Shine Lan-X data logger enables a secure and direct Ethernet connection between Growatt inverters and the Internet router. This makes it easy to monitor and maintain installed Growatt devices online. The data from the connected Growatt inverters is stored on the Shine LAN-X data logger for up to one month. The data transfer rate of the USB port is up to 12 Mbps and up to 10 Mbps via the LAN connection. Plug&PlayNo configurationImmediately ready for operation

NOQON BTS1 Bluetooth dongle The NOQON BTS1 Bluetooth dongle can be connected to an MPPT solar charge controller to display the following values in the app: Charging current (A), solar battery voltage (V), solar power (W), solar electricity meter (Ah and WH) Suitable for the following solar charge controllers: - NOQON SCD12 MPPT solar charge controller Dual 12V 165Wp 50V 12A - NOQON SCD25 MPPT solar charge controller Dual 12V 350Wp 50V 25A - NOQON SCN20 MPPT solar charge controller 12V/24V 240Wp/480Wp 50V 20A - NOQON SCN40 MPPT solar charge controller 12V/24V 480Wp/960Wp 50V 40A

The Votronic 5545 tank electrode 15-50 K is a universally applicable tank sensor for measuring the tank level. The tank electrode 15-50 K is suitable for fallow water and sewage tanks as well as for drinking water tanks. Thanks to the use of appropriate materials, these tank sensors also comply with the DIN 2001-2 drinking water regulations and are designed for tanks with a height of between 15 and 50 cm.Another special feature is that the tank electrodes can be mounted on the top of the tank from the inside as well as from the outside. For fresh water tanks, they can even be mounted on the underside of the tank.Key product features of the 15-50 K tank electrode Rod electrode, easy to shorten to tank height For tanks with a height between 15 and 50 cm Installation diameter 38 mm (or PG 29 thread) Flange diameter 46.5 m Connection cable 75 cm long Simple adjustment to the specified tank height Test mark: E-test (EMC/vehicle directive) Complies with DIN standard 2001-2 from the Drinking Water Ordinance Linear, infinitely variable fill level signal Suitable for 12V and 24V continuous operation Optimal in combination with Votronic level indicators The tank sensor is compatible with the following Votronic gauges: Fresh water tank gauge S, 5311 Waste water indicator S, 5313 Holding tank indicator S, 5315 Info Panel Pro, 5330 Info Panel Pro 24V VPC Terra VPC Mercury VPC Jupiter 100 Smart Shunt, 5747 VPC Jupiter 200 Smart Shunt, 5748 VPC Jupiter 400 Smart Shunt, 5749 Scope of delivery:1x Votronic 5545 15-50 K tank sensor1x mounting material consisting of sealing ring, union nut PG 29, connection cable 75 cm1x operating instructions

A practical quick connector for batteries that are difficult to reach or concealed. The eyelet terminals are fitted to the battery, making connection child's play without the operator having to actually reach the battery. Comfort Connect eyelets are available in three different sizes for different battery terminal sizes. Checks the charging status of hard-to-reach batteries, M8 8.4 mm eyelet The indicator makes it easy to monitor the battery charge status. The exact battery result is displayed two hours after the vehicle has been parked. Functions Red: The battery voltage is below 12.4 V. It is definitely time to recharge the battery. Yellow: The battery voltage is between 12.4 and 12.65 V. It is time to recharge the battery. Green: The battery voltage is above 12.65 V. OK! No need to charge.

The WiFi-F from Growatt is an easy-to-install monitoring extension for complete control of the status values of your PV system. The device is attached to the inverter, allowing the inverter to receive or send data. The maximum range is 100M. The inverter data is transmitted to the Growatt Monitoring Cloud, which can be used free of charge. The system data is visually processed and stored there. The data can be retrieved via the Shinephone app or via the browser connection.

The fresh water tank gauge S from Votronic (MPN 5311) was designed for precise level measurement and can be used for all tank materials and tank sizes. The tank level is visualized via a 3-colour scalar, which is displayed on 10 LEDs, each representing 10% of the tank content. The display works continuously, as intermediate levels are displayed with variable brightness and therefore trends can be recognized immediately.The fresh water tank display S is designed as a panel version to match the VOTRONIC modular system and fits in perfectly with other VOTRONIC display units (uniform height 85 mm). Of course, it is also possible to retrofit a single display in the vehicle. Small front panel dimensions and the particularly low installation depth of just 18 mm allow installation in almost any location. The indicator is protected against reverse polarity and overload and is easy to connect via screw terminals on the back of the device.Key product features of the fresh water tank indicator S, 5311 Suitable for 12V and 24V DC operating voltage Low current consumption: only 1 - 30 mA Test mark: E-test, (EMC/vehicle directive) Panel dimensions WxHxD: 47 x 85 x 20 mm Installation dimensions: 29 x 63 x 18 mm Can be switched on and off at the touch of a button High display resolution of the tank level thanks to 10-stage display Suitable for the Votronic module system Can also be operated with 2 tank sensorsThe display units can also be assigned to 2 tanks (e.g. indoor/outdoor tank, summer/winter operation, additional tank, etc.). Single switches 2xUM are suitable for switching, e.g. switch panel 16 A S art. no. 1289 or switch panel 2x16 A S art. no. 1291Compatible with many Votronic tank sensors Tank electrode 12-24 K, 5543 Tank electrode 15-50 K, 5545 Tank electrode 20 K-WC, 5555 Tank sensor FL, 5530 Tank sensor 30-110 K-FL, 5551 Scope of delivery:1x Votronic 5311 fresh water tank display S1x set of fixing screws1x drilling template1x Operating instructions

A practical quick connector for batteries that are difficult to reach or hidden away. The eyelet terminals are fitted to the battery, making it very easy to connect without the operator having to actually reach the battery. Cable with M6 6.4 mm eyelet for quick and easy connection without clamps Functions Eyelet terminal M6 6.4 mm

The LCD Charge Control S is a convenient, easy-to-use control and operating element that displays the status of the individual charging sources, the current charging phase, the voltage of the on-board and starter battery and the current charging current. In solar mode, the displays for the current solar power (W) and the energy counters (Wh and Ah, can be reset to "zero" at any time) are also available for your own statistical purposes. With the VBCS or VAC Triple, the mains charging mode can be switched on or off manually or reduced in terms of power (AC power limit) at the touch of a button, e.g. if the shore power is too weak. A special protective function ensures that an inadvertently switched off mains charge is reactivated if the on-board battery is in danger of being deeply discharged. The large, clear display has an illuminated and easy-to-read display with very low power consumption. The plug and play connection means it can be easily retrofitted at any time, even retrospectively, and its compact design means it can be installed in almost any location. The product has the following features: Compatible with VOTRONIC VBCS chargersLarge, clear displayBright, white illuminated displayDisplay of the active charging source mains/charging converter/solarControl of the mains charging function, AC power limit Display of battery charging phasesVoltage and charging current displaysSolar computer function

VOLTIMA Charge Monitor VBCR The VBRC monitor from VOLTIMA is the perfect addition to the VOLTIMA charge boosters. Simply connect the long cable to your charge booster and mount the display in a suitable place in your vehicle. Power is supplied via the charging booster, so no additional connection cable is required. The backlighting of the display can be adjusted according to your wishes. From now on, you are always informed about the charge status of your supply battery and the performance of the charge booster. The Charge Monitor displays the following values: Charging current (amperes) Battery voltage (volts) Charging power (watts) State of charge (Ah/Wh) Perfect interaction with the VOLTIMA charge boosters VBS25 or VBS40

With the Growatt ShineLink WiFi module, all inverter data is stored and can be accessed via the Shinelink. This gives a clear picture of the performance of the Growatt inverters and the data archive of the ShineLink is backed up for 30 days. The ShineLink can monitor up to 8 inverters and has a range of 120 meters. The Growatt ShineLink-X data logger (MPN: ShineLink-X) is used for online monitoring and maintenance of a Growatt inverter. Memory data is recorded over a period of one month. Data protection plays a major role in wireless communication, so this information can be encrypted. The Growatt servers are based in Frankfurt.The ShineLink-X at a glanceMonitoring of up to 8 invertersRatio frequency communication120m rangePlug and playAutomatic IP addressingEncrypted dataBuilt-in memory for one monthCable-free, easy installationGrowatt Shine monitoring platformThe Growatt monitoring platform can be used with the ShineLink-X. This is available as a smartphone app (for iOS and Android) and as a web version. Use of the platform is free of charge. All Growatt products that are owned can be configured and monitored via Shine. It is also possible to display self-consumption and trends.Compatible inverter series:MIC 600-3300TL-XMIN 2500-4600TL-X/XH/XAMOD 3-15KTL3-X/XHMID 17-22KTL3-X/XHMID 25-40KTL3-XMAX 50-80KTL3 LVMAX 100-125KTL3 LVSPH 3000-6000TL BL-UPSPH 4000-10000TL3 BH-UPSPA 4000-10000TL3 BH-UPTechnical data:Communication: Rf433 - up to 120m (under free field conditions)Input voltage AC power supply: 196-250VDimensions: 105 x 85 x 26 mmWeight: 1kgMounting: Table or wall mounting possibleProtection class: IP30Status display: LEDOperating temperature range: -20°C - +65°CManufacturer's warranty: 1 yearScope of delivery:1x ShineLan Box1x ShineRF Stick-X1x network cable

The level gauge / tank electrode FL from Votronic (MPN 5530) is based on a flexible cable probe and can be easily shortened to the appropriate tank height. The tank sensor is ideally suited for both fresh water tanks and waste water tanks. Thanks to the use of appropriate materials, these tank sensors also comply with the DIN 2001-2 drinking water regulations. The tank sensor is designed for high tanks with a height of between 30 and 110 cm.Another special feature of the Votronic FL tank electrode is that it can be mounted both on the inside and outside of the tank. The top and side walls of the tank can be used for mounting the Tank Sensor FL.Key product features of the Tank Sensor FL 5530 Permissible operating voltage: 12V and 24V DC (suitable for continuous operation) for mounting on the top or side wall of the tank suitable for fresh and waste water tanks suitable for tank heights from 30 to 100 cm Linear, stepless signal of the fill level Test mark: E-test (EMC/vehicle directive) Complies with DIN standard 2001-2 from the Drinking Water Ordinance Flexible cable probe, easy to shorten to tank height Installation diameter 38 mm (or PG 29 thread) Flange diameter 46.5 mm Connection cable 75 cm long for plastic tanks: wall thickness max. 8 mm Optimal in combination with Votronic level indicators The tank sensor is compatible with the following Votronic gauges: . Fresh water tank gauge S, 5311 Waste water indicator S, 5313 Holding tank indicator S, 5315 Info Panel Pro 5330 Info Panel Pro 24V VPC Terra VPC Mercury VPC Jupiter 100 Smart Shunt, 5747 VPC Jupiter 200 Smart Shunt, 5748 VPC Jupiter 400 Smart Shunt, 5749 Scope of delivery:1x Votronic 5530 FL tank sensor1x Flexible cable probe, sealing ring and PG 29 union nut1x Operating instructions

Battery temperature sensor with 3 m connection cable and M8 mounting hole. Potted against environmental influencesSuitable for all VOTRONIC automatic chargers of the Pb and VAC series, VCC charging converters and solar controllers of the SR and MPP series.

A practical quick connector for batteries that are difficult to reach or hidden away. The eyelet terminals are fitted to the battery, making connection child's play without the operator having to actually reach the battery. Comfort Connect - Eyelet are available in three different sizes for different battery terminal sizes. Eyelet: M10 (10.4 mm) Cable length for all models: 40 cm Cable with M8 8.4 mm eyelet for quick and easy connection without clamps Functions Eyelet clamp M8 8.4 mm

The Votronic waste water tank gauge S (MPN 5313) was designed for precise level measurement and can be used for all tank materials and tank sizes. The tank level is visualized via a 3-colour scale, which is displayed on 10 LEDs, each representing 10% of the tank content. The display works continuously, as intermediate levels are displayed with variable brightness and therefore trends can be recognized immediately.The waste water tank display Tank display S is designed as a panel version to match the VOTRONIC modular system and fits in perfectly with other VOTRONIC display units (uniform height 85 mm). Of course, it is also possible to retrofit a single display in the vehicle. Small front panel dimensions and the particularly low installation depth of just 18 mm allow installation in almost any location. The indicator is protected against reverse polarity and overload and is easy to connect via screw terminals on the back of the device.Key product features of the waste water tank indicator S, 5313 Suitable for 12V and 24V DC operating voltage Low current consumption: only 1 - 30 mA Test mark: E-test, (EMC/vehicle directive) Panel dimensions WxHxD: 47 x 85 x 20 mm Installation dimensions: 29 x 63 x 18 mm Can be switched on and off at the touch of a button High display resolution of the tank level thanks to 10-stage display Suitable for the Votronic module system Can also be operated with 2 tank sensors The display units can also be assigned to 2 tanks (e.g. indoor/outdoor tank, summer/winter operation, additional tank, etc.). Single switches 2xUM are suitable for switching, e.g. switch panel 16 A S art. no. 1289 or switch panel 2x16 A S art. no. 1291Compatible with many Votronic tank sensors Tank electrode 12-24 K, 5543 Tank electrode 15-50 K, 5545 Tank electrode 20 K-WC, 5555 Tank sensor FL, 5530 Tank sensor 30-110 K-FL, 5551 Scope of delivery:1x Votronic 5313 waste water tank display S1x set of fixing screws1x drilling template1x operating instructions

Perfectly suited for cars, motorcycles, boats, lawnmowers, jet skis, etc. It can remain permanently connected and is therefore always able to indicate when the battery needs recharging.

The Votronic 5551 tank electrode 30-110 K-FL is a universally applicable tank sensor for measuring the tank level of drinking or fresh water tanks. The tank electrode 30-110 K-FL is suitable for both waste water tanks and fresh water tanks. Thanks to the use of appropriate materials, these tank sensors also comply with the DIN 2001-2 drinking water regulations. The tank sensor is designed for high tanks with a height of between 30 and 110 cm.Another special feature is that the tank electrodes can be mounted on the top of the tank from the inside as well as from the outside. In the case of fresh water tanks, they can even be mounted on the underside of the tank.Key product features of the 30-110 K-FL tank electrode Permissible operating voltage: 12V and 24V DC for installation on the top of the tank Suitable for drinking water and waste water tanks Flexible cable probe, easy to shorten to tank height Linear, stepless signal of the fill level Test mark: E-test (EMC/vehicle directive) Complies with DIN standard 2001-2 from the Drinking Water Ordinance Installation diameter 38 mm (or PG 29 thread) Flange diameter 46.5 mm Connection cable 75 cm long For plastic tanks: wall thickness max. 8 mm Optimal in combination with Votronic level indicators The tank sensor is compatible with the following Votronic gauges: Fresh water tank gauge S, 5311 Waste water gauge S, 5313 Holding tank indicator S, 5315 Info Panel Pro 5330 Info Panel Pro 24V VPC Terra VPC Mercury VPC Jupiter 100 Smart Shunt, 5747 VPC Jupiter 200 Smart Shunt, 5748 VPC Jupiter 400 Smart Shunt, 5749 Scope of delivery:1x Votronic 5551 30-110 K-FL tank sensor1x Flexible cable probe, sealing ring, union nut PG 291x operating instructions

Bluetooth Connector S-BC from Votronic The Votronic Energy Monitor consists of a special communication module (Bluetooth Connector S-BC) which, in conjunction with a Votronic solar charge controller (from 2014 serial number (serial number 14Vxx.xxxxx)) with LCD Solar Computer S and/or the LCD Battery Computer S or VPC Jupiter with Smart Shunt, also transmits the values shown on the corresponding display to a mobile device via Bluetooth. The required app for Android or IOS is available free of charge in the Google Play Store or IOS App Store Connecting the Bluetooth Connector S-BC is very easy. It is simply plugged between the Votronic solar charge controller and the LCD Solar Computer S or between the Smart Shunt and the LCD Battery Computer S or VPC Jupiter using the modular cable included in the scope of delivery. The device has 2 inputs and 2 outputs, so that 1 solar controller with LCD solar computer and 1 Smart Shunt with LCD battery computer or VPC Jupiter can be connected together to a communication module. In this way, all the information from the on-board battery, such as voltage, charging and discharging currents and the remaining capacity, as well as all the data from the solar system can be conveniently read via a cell phone or tablet. In addition, the most important data is logged, graphically processed and stored for a longer period of time. It is even possible to output the data as a CSV file for your own analysis purposes. Of course, the Bluetooth Connector S-BC can also be retrofitted at any time. Technical features Connection via Bluetooth 4.0 (2.4Ghz) Range up to 50 outdoors Compatible with Votronic solar controller, VBCS Triple Charger, LCD battery computer and VPC Jupiter Dimensions HxWxD in mm: 75 x 47 x 24 Weight: 37g Test mark: CE, E-test (EMC/vehicle directive) Scope of delivery: Votronic Bluetooth Connector S-BC (MPN 1430), operating instructions, 2 x control cable 6-pin 1m long

The Votronic Info Panel Pro (MPN 5330) for 12V systems is a convenient display and control panel and has been specially developed for use in motorhomes. It takes over the most important control and switching tasks and offers direct monitoring of fresh water, waste water and waste tanks, as well as the on-board and starter battery. It is also equipped with a main battery switch and a main pump switch for the fresh water supply.On the left-hand side, several LEDs indicate the current battery voltage in a range from 10.5V to 15.0V. If the voltage is too low, this is signaled by red LEDs. At the touch of a button, you can switch between the voltage display of the on-board and starter battery or deactivate the display.There are two further displays on the Info Panel Pro for monitoring tanks, which are represented by light bars with 10 LEDs each. The displays work continuously, as intermediate levels are displayed with variable brightness and trends can therefore be recognized immediately. This gives you a complete overview of all filling and emptying processes. The display can be switched on and off at the touch of a button and switches off again automatically after approx. 10 minutes. The tank display on the right-hand side of the Info Panel Pro can also be switched to two measuring inputs (e.g. waste water and waste tank) as standard.The Info Panel Pro is equipped with integrated protection against reverse polarity and overload. The labeled connections for 6.3 mm flat plugs (power connections) and screw terminals (signal connections) are located on the rear.To make installation easier for you, you also receive a drilling template with the Info Panel Pro. Thanks to the low installation depth of just 15 mm, the device can be installed almost anywhere.Scope of delivery:1v Votronic Info Panel Pro 5330, operating instructions

The Comfort M8 connector is designed for mounting on the battery with eyelets - Eyelet diameter 8.4 mm - Cable length 0.55 m - Illuminated microdiodes indicate three levels of battery status - 15 A fuse

The Votronic 5748 VPC Power Control Jupiter 200 is part of an innovative series of combination panels that have been specially developed for installation in motorhomes. It combines the functions of the Merkur 5744 and Terra 5741 models and also has a lot more to offer as it combines a solar computer, battery computer and water management in just one device. The 200 is the second most powerful version of the new Multi-Panel series from Votronic. It differs from the 100 and 400 versions only in the maximum battery current that can be measured by the Jupiter Panel and the supplied Smart Shunt + ground strap. In terms of functionality, the three devices are identical.The Jupiter series is currently the benchmark for measuring and display devices in the motorhome sector. No other panel offers such a wide range of functions, measurement and display options. Jupiter is also significantly cheaper than buying all the devices individually.Integrated solar computerThe solar computer of the Jupiter combi panel corresponds in performance and function to the Solar-Computer S. The solar display is compatible with most Votronic charge controllers and the Triple series. Among other things, it shows the current solar power in W, the current solar current in A, the charged solar capacity in Ah and the charged solar energy in kWh. The solar computer provides a comprehensive picture of the current performance of your motorhome solar system.Integrated battery computer incl. smart shunt and ground strapCorresponds in terms of performance to the single device Battery Computer 200 S, which is also available as a 100 and 400A version. The Votronic battery computer provides a comprehensive impression of the condition of your starter and board battery and offers numerous functions.Microprocessor-controlled, the following values are measured, calculated and displayed: Max. battery current: 200A On-board battery voltage 7 to 32 V (volts). Internal measurement resolution 0.1 V Allows conclusions to be drawn about the battery behavior under different loads and is used for function checks, e.g. of the charger, solar system, alternator, etc. Flashing warning display in the event of overvoltage Battery current (charge/discharge) +/- 0 to max. +/- 1800 A, internal measurement resolution 0.1 A Checking the discharge currents (load) by consumers, indicated by a "-" sign, control of charging currents, indicated by a "Charge" sign Battery capacity (Ah and %) Remaining charge from 0 Ah / 0% (empty) to nominal capacity max. 2000 Ah / 100% (full) Battery voltage 2nd battery (e.g. starter battery), 7 to 32 V (volts), internal measurement resolution 0.1 V Switching output freely programmable and tactile (PNP, plus potential 12V / 24V, max. 0.5A) incl. remaining run indicator Integrated level indicator for water tanksThe third important highlight of the Jupiter 200 is the level indicator for the fresh and waste water tanks. Together with the 16A switch for the fresh water pump, water management can also be implemented via the Jupiter combi panel.Other important features Voltage display for the starter battery Potential-free switching output for an external relay with freely programmable switching thresholds (% residual capacity) as deep discharge protection and as a main switch Indoor and outdoor thermometer incl. 1 indoor and 1 outdoor sensor Clock in 24-hour format Double USB charging socket (5 V/2.5 A) Simple, intuitive operation Important technical data Simple, intuitive operation Specially developed for use in motorhomes and camper vans Compact, simple installation low installation depth, low power consumption for 12 V or 24 V batteries Display dimensions: 200x65x30 mm Installation dimensions: 185x57x24 mm Weight without smart shunt: only 200g High-quality technology made in Germany Scope of delivery:1x Votronic 5748 VPC Jupiter 200 Multi-Panel1x operating instructions1x temperature sensor for indoor use1x temperature sensor for outside1x Smart measuring shunt for connecting the battery computer2x 5m connection cables (stereo cables)1x 35mm ground strap for measuring shunt connection

Votronic remote control S suitable for automatic chargers of the Pb and VAC series. If the device is difficult to access, the control LEDs provide a remote display of the device status and charging progress. One of the respective main device functions can be remote-controlled with the switch, e.g. silent run (night mode) for chargers in the Pb and VAC series. The remote control is designed as a panel version and matches the other displays of the VOTRONIC module system both visually and mechanically (same height 85 mm). Product details Automatic loaders Pb series Automatic loaders VAC series Made in Germany Technical data Dimensions 85x47mm Installation dimensions 65x35 (max. depth 16 mm) Weight 23g Test mark CE, E-test (EMC/vehicle directive) Scope of delivery Connection cable 5m long, ready to plug in on both sides for device connection, fixing screws, drilling template

The Growatt Shinewifi-S Wifi Stick is used to connect the hybrid inverter to the Internet. The Growatt Shinewifi-S Wifi Stick is compatible with the single-phase Growatt SPH and Growatt SPA TL3 BH inverter series.

Cable for checking the battery status via a 12-volt socket INDICATOR CIG PLUG is a combination of quick connector and indicator for easy charging. Perfect for checking the charge status and charging the battery via the vehicle's 12V socket. Suitable for all 12 V chargers from CTEK up to 8 A. INDICATOR CIG PLUG is a universal device for 12 and 21 mm sockets. Note: The socket must be supplied with power even if the ignition switch is in the "off" position. Functions Red: The battery voltage is below 12.4 V. It is definitely time to recharge the battery. Yellow: The battery voltage is between 12.4 and 12.65 V. It is time to recharge the battery. Green: The battery voltage is above 12.65 V. OK! No need to charge.