Paco PV2412-50 24V to 12V 50A voltage converter

This VOTRONIC DCDC series DC/DC converter enables safe operation of 12V consumers on 12V vehicle electrical systems without the need for a separate battery system.The devices can be operated for short periods with up to 30% overload, so that inrush, peak and starting currents of the various consumers are also absorbed.Galvanic insulation is installed between the input and output sides to protect against voltage breakdowns, defective earth cables and the like. This ensures perfect, independent earthing conditions on both sides even with long connection cables, which is useful for large vehicles, containers, roller containers, trailers etc., for example.After activating the DC/DC converter at the ON/OFF control input, which can be done either by a switching signal, vehicle ignition or D+, the voltage monitoring of the battery is also ready for operation (charge detection on the starter battery, undervoltage cut-off).Output voltage:It is stabilized and smoothed and therefore ideally suited even for sensitive consumers. The output voltage can be optionally set to three fixed, stabilized output voltages.In the fourth switch position, the level of the input voltage at the output is variably adjusted.In this operating mode, it is also advantageous to operate consumers that obtain additional information from the 12V operating voltage, e.g. starter battery is being charged, driving or standby mode, automatic switch-off in the event of undervoltage and battery discharge (small devices, charging trays, lamps) etc.Device features of the DCDC series: The output voltage is stabilized, free of peaks, smoothed and filtered. Galvanic isolation between input and output: - Absolute isolation of the loads and the battery circuit, even in the event of a fault. This is a particularly important feature, e.g. when operating 12V consumers from a higher 24V system voltage:- No destruction of e.g. 12V consumers in the event of overvoltage due to 24V breakdowns.- No overvoltage at the output and thus protection of the loads in the event of loss of the earth line.- Clean, undisturbed earth conditions even with long supply cables.- Stable operating voltage on site in mobile operation, e.g. containers, trailers, roller containers, etc.- Filtering and suppression of interference from the input to the output side. Fully automatic continuous operation: The DC/DC converter can be permanently connected to the battery and the loads and operates manually or automatically according to the set specifications. Monitoring-free operation: Multiple protection against overload, overheating, overvoltage, short circuit, malfunction and battery deep discharge through electronic regulation up to complete switch-off by built-in safety switches. Supply cable compensation: Voltage losses on the cables are taken into account. Built-in on-board mains filter: Problem-free parallel operation with solar systems, wind and petrol generators, mains chargers etc. on one battery. Scope of delivery:DCDC 1212-20 DC/DC converter, operating instructions

This VOTRONIC DCDC series DC/DC converter enables safe operation of 24V consumers on 12V vehicle electrical systems without the need for a separate battery system.The devices can be operated for short periods with up to 30% overload, so that inrush, peak and starting currents of the various consumers are also absorbed.Galvanic insulation is installed between the input and output sides to protect against voltage breakdowns, defective earth cables and the like. This ensures perfect, independent earthing conditions on both sides even with long connection cables, which is useful for large vehicles, containers, roller containers, trailers etc., for example.After activating the DC/DC converter at the ON/OFF control input, which can be done either by a switching signal, vehicle ignition or D+, the voltage monitoring of the battery is also ready for operation (charge detection on the starter battery, undervoltage cut-off).Output voltage:It is stabilized and smoothed and therefore ideally suited even for sensitive consumers. The output voltage can be optionally set to three fixed, stabilized output voltages.In the fourth switch position, the level of the input voltage at the output is variably adjusted.In this operating mode, it is also advantageous to operate consumers that obtain additional information from the (12V or 24V) operating voltage, e.g. starter battery is being charged, driving or standby mode, automatic switch-off in the event of undervoltage and battery discharge (small appliances, charging trays, lamps), etc.Device characteristics: The output voltage is stabilized, free of peaks, smoothed and filtered. Galvanic isolation between input and output: - Absolute isolation of the loads and the battery circuit, even in the event of a fault. This is a particularly important feature, e.g. when operating 12V consumers from a higher 24V system voltage:- No destruction of e.g. 12V consumers in the event of overvoltage due to 24V breakdowns.- No overvoltage at the output and thus protection of the loads in the event of loss of the earth line.- Clean, undisturbed earth conditions even with long supply cables.- Stable operating voltage on site in mobile operation, e.g. containers, trailers, roller containers, etc.- Filtering and suppression of interference from the input to the output side. Fully automatic continuous operation: The DC/DC converter can be permanently connected to the battery and the loads and operates manually or automatically according to the set specifications. Monitoring-free operation: Multiple protection against overload, overheating, overvoltage, short circuit, malfunction and battery deep discharge through electronic regulation up to complete switch-off by built-in safety switches. Supply cable compensation: Voltage losses on the cables are taken into account. Built-in on-board mains filter: Problem-free parallel operation with solar systems, wind and petrol generators, mains chargers etc. on one battery. Scope of delivery:DCDC 1224-25 DC/DC converter, operating instructions

Paco PV2412-30 24V to 12V 30A voltage converter

This VOTRONIC DCDC series DC/DC converter enables safe operation of 12V consumers on 12V vehicle electrical systems without the need for a separate battery system.The devices can be operated for short periods with up to 30% overload, so that inrush, peak and starting currents of the various consumers are also absorbed.Galvanic insulation is installed between the input and output sides to protect against voltage breakdowns, defective earth cables and the like. This ensures perfect, independent earthing conditions on both sides even with long connection cables, which is useful for large vehicles, containers, roller containers, trailers etc., for example.After activating the DC/DC converter at the ON/OFF control input, which can be done either by a switching signal, vehicle ignition or D+, the voltage monitoring of the battery is also ready for operation (charge detection on the starter battery, undervoltage cut-off).Output voltage:It is stabilized and smoothed and therefore ideally suited even for sensitive consumers. The output voltage can be optionally set to three fixed, stabilized output voltages.In the fourth switch position, the level of the input voltage at the output is variably adjusted.In this operating mode, it is also advantageous to operate consumers that obtain additional information from the 12V operating voltage, e.g. starter battery is being charged, driving or standby mode, automatic switch-off in the event of undervoltage and battery discharge (small devices, charging trays, lamps) etc.Device features of the DCDC series: The output voltage is stabilized, free of peaks, smoothed and filtered. Galvanic isolation between input and output: - Absolute isolation of the loads and the battery circuit, even in the event of a fault. This is a particularly important feature, e.g. when operating 12V consumers from a higher 24V system voltage:- No destruction of e.g. 12V consumers in the event of overvoltage due to 24V breakdowns.- No overvoltage at the output and thus protection of the loads in the event of loss of the earth line.- Clean, undisturbed earth conditions even with long supply cables.- Stable operating voltage on site in mobile operation, e.g. containers, trailers, roller containers, etc.- Filtering and suppression of interference from the input to the output side. Fully automatic continuous operation: The DC/DC converter can be permanently connected to the battery and the loads and operates manually or automatically according to the set specifications. Monitoring-free operation: Multiple protection against overload, overheating, overvoltage, short circuit, malfunction and battery deep discharge through electronic regulation up to complete switch-off by built-in safety switches. Supply cable compensation: Voltage losses on the cables are taken into account. Built-in on-board mains filter: Problem-free parallel operation with solar systems, wind and petrol generators, mains chargers etc. on one battery. Scope of delivery:DCDC 1212-45 DC/DC converter, operating instructions

Paco PV2412-6 24V to 12V 6A voltage converter

This VOTRONIC DCDC series DC/DC converter enables safe operation of 12V consumers on 12V vehicle electrical systems without the need for a separate battery system.The devices can be operated for short periods with up to 30% overload, so that inrush, peak and starting currents of the various consumers are also absorbed.Galvanic insulation is installed between the input and output sides to protect against voltage breakdowns, defective earth cables and the like. This ensures perfect, independent earthing conditions on both sides even with long connection cables, which is useful for large vehicles, containers, roller containers, trailers etc., for example.After activating the DC/DC converter at the ON/OFF control input, which can be done either by a switching signal, vehicle ignition or D+, the voltage monitoring of the battery is also ready for operation (charge detection on the starter battery, undervoltage cut-off).Output voltage:It is stabilized and smoothed and therefore ideally suited even for sensitive consumers. The output voltage can be optionally set to three fixed, stabilized output voltages.In the fourth switch position, the level of the input voltage at the output is variably adjusted.In this operating mode, it is also advantageous to operate consumers that obtain additional information from the 12V operating voltage, e.g. starter battery is being charged, driving or standby mode, automatic switch-off in the event of undervoltage and battery discharge (small devices, charging trays, lamps) etc.Device features of the DCDC series: The output voltage is stabilized, free of peaks, smoothed and filtered. Galvanic isolation between input and output: - Absolute isolation of the loads and the battery circuit, even in the event of a fault. This is a particularly important feature, e.g. when operating 12V consumers from a higher 24V system voltage:- No destruction of e.g. 12V consumers in the event of overvoltage due to 24V breakdowns.- No overvoltage at the output and thus protection of the loads in the event of loss of the earth line.- Clean, undisturbed earth conditions even with long supply cables.- Stable operating voltage on site in mobile operation, e.g. containers, trailers, roller containers, etc.- Filtering and suppression of interference from the input to the output side. Fully automatic continuous operation: The DC/DC converter can be permanently connected to the battery and the loads and operates manually or automatically according to the set specifications. Monitoring-free operation: Multiple protection against overload, overheating, overvoltage, short circuit, malfunction and battery deep discharge through electronic regulation up to complete switch-off by built-in safety switches. Supply cable compensation: Voltage losses on the cables are taken into account. Built-in on-board mains filter: Problem-free parallel operation with solar systems, wind and petrol generators, mains chargers etc. on one battery. Scope of delivery:DCDC 1212-45 DC/DC converter, operating instructions

Paco PV2412-30 24V to 12V 30A voltage converter

Paco PV2412-40 24V to 12V 40A voltage converter

Paco PV2412-50 24V to 12V 50A voltage converter

Paco PV2412-6 24V to 12V 6A voltage converter

Paco PV2412-10 24V to 12V 10A voltage converter

Paco PV2412-20 24V to 12V 20A voltage converter

Remote on/off switch The remote on/off switch eliminates the need for a high-current switch on the input wiring. The remote on/off connection can be controlled by a power saving switch or by the motor's run/stop switch (see manual). Adjustable output voltage: Can also be used as a battery charger For example, to charge a 12 V starter or auxiliary battery in an otherwise 24 V system. All models are short-circuit-proof and can be connected in parallel to increase the output current. An unlimited number of devices can be connected in parallel. IP43 protection: If the device is installed with the screw terminals facing downwards. Screw terminals: No special tools are required for installation. Input fuse: Only on the 12 V and 24 V models Models:Orion-Tr Smart 12/12 18 A DC-DC charging booster isolated Fully encapsulated: waterproof, shockproof and fire retardant Water, oil or dirt cannot damage the Orion IP67 DC-DC converter. The housing is made of cast aluminum and the electronics are coated with resin. Extra-long input and output cables Thanks to the 1.8 m long cables, no additional extension cables are required in most cases. This supports safe operation in an area where IP67 protection is required. Wide input voltage range With an input voltage range of 15 to 40 volts, a stable output is guaranteed during voltage surges or undervoltages caused by other devices connected to the same battery Overheating protection Can be used in a hot environment such as an engine room 12 / 24 / 48 volts

Remote on/off switch The remote on/off switch eliminates the need for a high-current switch on the input wiring. The remote on/off connection can be controlled by a power saving switch or by the motor's run/stop switch (see manual). Adjustable output voltage: Can also be used as a battery charger For example, to charge a 12 V starter or auxiliary battery in an otherwise 24 V system. All models are short-circuit-proof and can be connected in parallel to increase the output current. An unlimited number of devices can be connected in parallel. IP43 protection: If the device is installed with the screw terminals facing downwards. Screw terminals: No special tools are required for installation. Input fuse: Only on the 12 V and 24 V models Models:Orion-Tr Smart 12/12 18 A DC-DC charging booster isolated Fully encapsulated: waterproof, shockproof and fire retardant Water, oil or dirt cannot damage the Orion IP67 DC-DC converter. The housing is made of cast aluminum and the electronics are coated with resin. Extra-long input and output cables Thanks to the 1.8 m long cables, no additional extension cables are required in most cases. This supports safe operation in an area where IP67 protection is required. Wide input voltage range With an input voltage range of 15 to 40 volts, a stable output is guaranteed during voltage surges or undervoltages caused by other devices connected to the same battery Overheating protection Can be used in a hot environment such as an engine room 12 / 24 / 48 volts

This VOTRONIC DCDC series DC/DC converter enables safe operation of 12V consumers on 24V vehicle electrical systems without the need for a separate battery system.The devices can be operated for short periods with up to 30% overload, so that inrush, peak and starting currents of the various consumers are also absorbed.Galvanic insulation is installed between the input and output sides to protect against voltage breakdowns, defective earth cables and the like. This ensures perfect, independent earthing conditions on both sides even with long connection cables, which is useful for large vehicles, containers, roller containers, trailers etc., for example.After activating the DC/DC converter at the ON/OFF control input, which can be done either by a switching signal, vehicle ignition or D+, the voltage monitoring of the battery is also ready for operation (charge detection on the starter battery, undervoltage cut-off).Output voltage:It is stabilized and smoothed and therefore ideally suited even for sensitive consumers. The output voltage can be optionally set to three fixed, stabilized output voltages.In the fourth switch position, the level of the input voltage at the output is variably adjusted.In this operating mode, it is also advantageous to operate consumers that obtain additional information from the 24V operating voltage, e.g. starter battery is being charged, driving or standby mode, automatic switch-off in the event of undervoltage and battery discharge (small appliances, charging trays, lamps), etc.Device characteristics: The output voltage is stabilized, free of peaks, smoothed and filtered. Galvanic isolation between input and output: - Absolute isolation of the loads and the battery circuit, even in the event of a fault. This is a particularly important feature, e.g. when operating 12V consumers from a higher 24V system voltage:- No destruction of e.g. 12V consumers in the event of overvoltage due to 24V breakdowns.- No overvoltage at the output and thus protection of the loads in the event of loss of the earth line.- Clean, undisturbed earth conditions even with long supply cables.- Stable operating voltage on site in mobile operation, e.g. containers, trailers, roller containers, etc.- Filtering and suppression of interference from the input to the output side. Fully automatic continuous operation: The DC/DC converter can be permanently connected to the battery and the loads and operates manually or automatically according to the set specifications. Monitoring-free operation: Multiple protection against overload, overheating, overvoltage, short circuit, malfunction and battery deep discharge through electronic regulation up to complete switch-off by built-in safety switches. Supply cable compensation: Voltage losses on the cables are taken into account. Built-in on-board mains filter: Problem-free parallel operation with solar systems, wind and petrol generators, mains chargers etc. on one battery. Scope of delivery:DCDC 2412-45 DC/DC converter, operating instructions

This VOTRONIC DCDC series DC/DC converter enables safe operation of 12V consumers on 24V vehicle electrical systems without the need for a separate battery system.The devices can be operated for short periods with up to 30% overload, so that inrush, peak and starting currents of the various consumers are also absorbed.Galvanic insulation is installed between the input and output sides to protect against voltage breakdowns, defective earth cables and the like. This ensures perfect, independent earthing conditions on both sides even with long connection cables, which is useful for large vehicles, containers, roller containers, trailers etc., for example.After activating the DC/DC converter at the ON/OFF control input, which can be done either by a switching signal, vehicle ignition or D+, the voltage monitoring of the battery is also ready for operation (charge detection on the starter battery, undervoltage cut-off).Output voltage:It is stabilized and smoothed and therefore ideally suited even for sensitive consumers. The output voltage can be optionally set to three fixed, stabilized output voltages.In the fourth switch position, the level of the input voltage at the output is variably adjusted.In this operating mode, it is also advantageous to operate consumers that obtain additional information from the 24V operating voltage, e.g. starter battery is being charged, driving or standby mode, automatic switch-off in the event of undervoltage and battery discharge (small appliances, charging trays, lamps), etc.Device characteristics: The output voltage is stabilized, free of peaks, smoothed and filtered. Galvanic isolation between input and output: - Absolute isolation of the loads and the battery circuit, even in the event of a fault. This is a particularly important feature, e.g. when operating 12V consumers from a higher 24V system voltage:- No destruction of e.g. 12V consumers in the event of overvoltage due to 24V breakdowns.- No overvoltage at the output and thus protection of the loads in the event of loss of the earth line.- Clean, undisturbed earth conditions even with long supply cables.- Stable operating voltage on site in mobile operation, e.g. containers, trailers, roller containers, etc.- Filtering and suppression of interference from the input to the output side. Fully automatic continuous operation: The DC/DC converter can be permanently connected to the battery and the loads and operates manually or automatically according to the set specifications. Monitoring-free operation: Multiple protection against overload, overheating, overvoltage, short circuit, malfunction and battery deep discharge through electronic regulation up to complete switch-off by built-in safety switches. Supply cable compensation: Voltage losses on the cables are taken into account. Built-in on-board mains filter: Problem-free parallel operation with solar systems, wind and petrol generators, mains chargers etc. on one battery. Scope of delivery:DCDC 2412-25 DC/DC converter, operating instructions

This VOTRONIC DCDC series DC/DC converter enables safe operation of 24V consumers on 12V vehicle electrical systems without the need for a separate battery system.The devices can be operated for short periods with up to 30% overload, so that inrush, peak and starting currents of the various consumers are also absorbed.Galvanic insulation is installed between the input and output sides to protect against voltage breakdowns, defective earth cables and the like. This ensures perfect, independent earthing conditions on both sides even with long connection cables, which is useful for large vehicles, containers, roller containers, trailers etc., for example.After activating the DC/DC converter at the ON/OFF control input, which can be done either by a switching signal, vehicle ignition or D+, the voltage monitoring of the battery is also ready for operation (charge detection on the starter battery, undervoltage cut-off).Output voltage:It is stabilized and smoothed and therefore ideally suited even for sensitive consumers. The output voltage can be optionally set to three fixed, stabilized output voltages.In the fourth switch position, the level of the input voltage at the output is variably adjusted.In this operating mode, it is also advantageous to operate consumers that obtain additional information from the (12V or 24V) operating voltage, e.g. starter battery is being charged, driving or standby mode, automatic switch-off in the event of undervoltage and battery discharge (small appliances, charging trays, lamps), etc.Device characteristics: The output voltage is stabilized, free of peaks, smoothed and filtered. Galvanic isolation between input and output: - Absolute isolation of the loads and the battery circuit, even in the event of a fault. This is a particularly important feature, e.g. when operating 12V consumers from a higher 24V system voltage:- No destruction of e.g. 12V consumers in the event of overvoltage due to 24V breakdowns.- No overvoltage at the output and thus protection of the loads in the event of loss of the earth line.- Clean, undisturbed earth conditions even with long supply cables.- Stable operating voltage on site in mobile operation, e.g. containers, trailers, roller containers, etc.- Filtering and suppression of interference from the input to the output side. Fully automatic continuous operation: The DC/DC converter can be permanently connected to the battery and the loads and operates manually or automatically according to the set specifications. Monitoring-free operation: Multiple protection against overload, overheating, overvoltage, short circuit, malfunction and battery deep discharge through electronic regulation up to complete switch-off by built-in safety switches. Supply cable compensation: Voltage losses on the cables are taken into account. Built-in on-board mains filter: Problem-free parallel operation with solar systems, wind and petrol generators, mains chargers etc. on one battery. Scope of delivery:DCDC 1224-25 DC/DC converter, operating instructions

Paco PV2412-40 24V to 12V 40A voltage converter

Paco PV2412-10 24V to 12V 10A voltage converter

Paco PV2412-20 24V to 12V 20A voltage converter