Noqon NPC8 battery charger 12V/24V with 8A charging current The car battery charger is an 11-step car battery charger suitable for charging and trickle charging 12V or 24V lead-acid batteries (batteries) with liquid electrolyte (WET), maintenance-free lead-acid batteries (MF), gel electrolyte (GEL) or electrolyte-absorbing mats (AGM). Select the desired charging voltage (12V or 24V) and the microprocessor-controlled charger takes care of everything fully automatically until the charging cycle is complete and the batteries are fully charged. The German-language display is easy to understand and convenient to operate. Thanks to the test function, battery charge levels can be determined before charging and the integrated memory function continues the charging process even after power interruptions without having to start from the beginning. There aresix charging programs to choose from. Fully automatic battery charging takes place in 11 charging steps. Modern safety technology with reverse polarity protection, overheating protection, overload protection and short-circuit protection protects you and the device from incorrect operation. Two cables with quick connectors and comfort plugs (permanent charging cable with eyelets for fixed installation & charging cable with clamps) are included with the jet-proof and dust-proof device (protection class IP65). Features: Suitable for continuous charging Test function/battery tester Memory function 6 charging programs 11 charging steps Technical data: Specification: at 12 V: 3.8 A / 0.8 A, 6 V: 0.8 A, microprocessor-controlled Power supply: 220V - 240V, 50Hz Charging voltage: 14.4V/14.7V ±0.25 VDC, 28.8V/29.4V ±0.25 VDC Rated output current: 12V: 2A / 8A ±10% - 24V: 4A ±10% Current consumption: Max. 0.9 A / 230 V Charger type: 11 charging steps, automatic charging cycle Ambient temperature: -10 to +40 °C Battery type: 12V & 24V lead-acid batteries (Wet, MF, GEL, EFB, AGM) Recommended battery capacity: 12V: 2.2 - 180Ah / 24V: 14 - 120Ah Protection class: IP65, protected against water jets Protection: Reverse polarity, thermal and overload protection, time control Scope of delivery: 1 x Noqon NPC8 battery charger 1 x crocodile clips 1 x quick contact cable with ring terminals

For heavy-duty vehicles The D250TS is a fast, fully automatic 4-stage DC/DC battery charger with disconnect function for vehicles with dual 24 V battery banks. The D250TS is ideal for buses, commercial vehicles, motorhomes and boats. It delivers 10 A for 24 V batteries between 28 Ah and 200 Ah and has a 12 V output for supplying the starter battery and connected 12 V consumers. The D250TS complies with protection class IP65 for outdoor use and is suitable for all types of lead-acid batteries, including maintenance-free, liquid, EFB, Ca/Ca, AGM and gel batteries. With the D250TS, you can rest assured that your batteries will always receive the optimum charging voltage. Features Quick installation at lower cost Automatically adapts to any connected power source Automatic battery equalization of 24 V systems Input voltage: 14-30 V DC Output: 28.8 V/10 A, 14.4 V/10 A

CTEK MXT 14 battery charger The MXT 14 is a 24V charger that has been developed for high-performance vehicles such as trucks, buses and commercial vehicle workshops. As a fully automatic 8-stage charger with a charging current of 14A, it is suitable for 24V batteries from 28-300Ah as well as for maintenance charging of up to 500Ah. The MXT 14 is also suitable for outdoor use (protection class IP44). RECOND: Special mode in which deeply discharged batteries are revived and restored to full capacitySUPPLY: Special mode in which the device can be used as a power supply unit for the equipment when the battery is removed (radio code)

Charging station with 12 V and 24 V for the workshop and saloon The MXTS 40 has both a 12 V/40 A output and a 24 V/20 A output and offers an adjustable constant voltage to prevent damage to the control unit due to voltage fluctuations during programming. In addition to the progress indicator for the 8-stage charging process, the MXTS 40 also has an easy-to-read OLED display that shows you important charging parameters such as amperage, voltage and recharged capacity. It has a recond mode for reconditioning deeply discharged batteries and a temperature sensor to optimize the charging process in all weather conditions. The MXTS 40 is designed to protect vehicle electronics and has a durable polycarbonate housing for harsh environments. The unit can be combined with the optional WALL HANGER PRO and TROLLEY PRO for secure storage and maximum portability. Features electronically safe, multi-stage fast charging process Outputs: 12 V/40 A and 24 V/20 A IP20 protection class non-sparking reverse polarity protected short-circuit proof

Ctek MXTS70, the ultimate charger for professionals! The MXTS 70 is a fully automatic 8-stage charger with a selectable charging current between 70 A/12 V and 35 A/24 V for 12 V batteries from 50 to 1000 Ah and 24 V batteries from 25 to 500 Ah. It is equipped with a high-strength aluminum housing for difficult working environments and protects vehicle electronics systems. It is protected against sparks, reverse polarity and short circuits and is equipped with all the features and functions required for professional battery care. Features: Supply mode (power supply function) Regeneration mode Temperature compensated Electronics safe Pulse charge retention Control panel with LED displays Selectable voltage range and amperage Display Detachable cable with heavy-duty clamps Cable length/Ø: approx. 5 m / 16 mm² Temperature compensated Fully automatic charging cycle with adjustable parameters.

PACO MEC2410 10A/24V battery charger

For 24 V batteries with power supply The MXT 4.0 is a cost-effective 8-stage charger with a charging current of 4 A for 24 V batteries between 8 Ah and 100 Ah and for trickle charging batteries up to 250 Ah. It can also be used for backup systems, snow groomers, industrial cleaning machines and wheelchairs. The functions of the MXT 4.0 include battery diagnostics, which determine whether the battery can accept and hold a charge, a recond mode for reconditioning deeply discharged batteries in which acid layers have formed, an optimized cold charging mode and an AGM mode. In supply mode, the device can be used as a power supply source. Functions Fully automatic, 8-stage "connect and forget" charging process Can be used as a power supply Easy to read LED display non-sparking reverse polarity protected short-circuit proof 2-year guarantee

Fully automatic 7-stage charger with processor-controlled IUoU characteristic curve for 24V batteries With the microprocessor-controlled Paco MBC charger, charging takes place automatically and protects the battery from harmful overcharging, so the charger can also be used as a trickle charger. The 7-stage charging process is a very comprehensive and accurate charging method that significantly extends battery life and improves battery performance data. The charger is suitable for most lead-acid battery types including calcium, gel and AGM batteries. In addition, the charger has a "reconditioning function", which makes so-called deeply discharged batteries fit for everyday use again by eliminating acid stratification and sulphation. Technical features of the charger: The charger has all modern functions such as: Soft start overvoltage protection Reconditioning Suitable for calcium, wet, AGM, fleece, VRLA and gel batteries Integrated automatically controlled fans Minimum starting voltage of only 2V Reverse polarity protection Overload protection Overheating protection Efficiency >85% The 7 stages at a glance: DESULPHATION (desulphation): Gently increasing and decreasing voltages and currents at the beginning of the charging process eliminate battery sulphation caused by short-distance driving and frequently discharged batteries. SOFTSTART (soft start): Regulated gently increasing voltages ensure a gentle transition and start to the main charge and prevent damage to the lead grids. BULK (main charge): The battery is charged at a steady current and carefully increasing voltage up to a predefined maximum voltage value until 80% of the total charge has been reached. ABSORPTION (residual charge): The battery is fully charged to 100% of the total charge by maintaining a constant voltage and gradually decreasing currents. The gradually decreasing current ensures that the terminal voltage does not become too high during full charging. BATTERY TEST: The battery is tested for self-discharge for 90 seconds. If the absorption phase has not been able to fully charge the battery and the voltage drop is therefore too high, which is the case with old batteries or batteries with strong acid stratification, for example, the system automatically switches to reconditioning mode RECONDITION (reconditioning): This mode starts with very low currents but high voltages of up to 32V, which remedies the acid stratification in deeply discharged batteries. This mode is limited to a maximum of 4 hours and improves battery life and performance. FLOAT/MAINTENANCE (charge retention/maintenance charge): The battery is evenly maintained at 27.6V "float" voltage without overcharging the battery or harming you. This means that the charger can also remain connected all year round (e.g. for seasonal vehicles/oldtimers) The voltage in this mode is permanently monitored. As soon as the voltage of the battery falls to a predefined level, the battery is recharged to 100% by a pulse charge and thus constantly kept between 95% and 100% state of charge. This cycle is repeated automatically and thus has a positive effect on the battery's service life. High-quality and durable workmanshipWith the Paco MBC charger, particular attention has been paid to a functional and durable external and internal design. For example, the housing is made of high-strength aluminum and is therefore robust and resistant to external influences, while the LED panel on the side of the device means you can always see which mode the charger is currently in.The solid battery terminals and plugs, which have a sufficient cable cross-section, are also of very good and durable quality.Scope of delivery: Paco MBC charger Detailed instructions for use, version: German/English

Votronic battery charger VAC-2425M 3A Built-in mains chargers for emergency vehicles and demanding motorhome and camper owners. Especially for rescue and emergency vehicles, the reliability of the batteries installed in the vehicle is crucial for the operational readiness of the vehicle. This is particularly the case when the batteries are subject to heavy loads from many continuous consumers, when there is not enough time to recharge them due to frequent use or when the charger is inadequately adapted to the batteries. In order to meet the special requirements of emergency vehicles, the VAC series was created in cooperation with vehicle and leading battery manufacturers.Votronic charging technology has been used for years in professional emergency vehicles such as fire engines, ambulances and coastguards! Quality - Made in Germany! The device electronics are protected against moisture and ensure safe operation in the event of severe temperature fluctuations. Continuous consumers connected to the vehicle electrical system (radios, charging trays etc.) are also supplied without impairing the charging process. The built-in charging current distributor also automatically supplies the starter battery with full charging current if required. The engine start lock can be activated via a signal output when the vehicle is connected to the mains.The devices are supplied with an 825 temperature sensor to ensure optimum charging of the batteries. The installation position is variable, thanks to a second device label included in the scope of delivery. Instead of a remote control, a waterproof LED display (see accessories) can be connected to the Remote Control connection socket, which indicates the operational readiness of the device on the outside of the vehicle.Further special features at a glance: Votronic products "Made in Germany" High charging power even for short journeys Significantly improved energy balance of the on-board battery Optimum charging characteristics for all battery types can be set using the battery selector switch (lead-acid, gel, AGM, lithium LiFePO4) Suitable for all alternators Automatic, adjustable power control ensures priority charging of the starter battery by the alternator when the vehicle electrical system is under heavy load, thus ensuring that the vehicle can be started again immediately Simple installation, no intervention in the vehicle's starter circuit required, device is connected in the charging line to the supply battery Parallel operation to increase power possible Particularly recommended for vehicles with Euro 6 standard Temperature sensor 825 already included in the scope of delivery The charging converters are also characterized by their compact design, low weight (high-frequency switching transformer, switch mode technology) and powerfully dimensioned power components. 6 operating displays provide information about the operating status of the device at all times. Recommended accessories: Votronic remote control S (2075) and remote operating display IP67 (2081)

Fully automatic 7-stage charger with processor-controlled IUoU characteristic curve for 24V batteries With the microprocessor-controlled Paco MBC charger, charging takes place automatically and protects the battery from harmful overcharging, so the charger can also be used as a trickle charger. The 7-stage charging process is a very comprehensive and accurate charging method that significantly extends battery life and improves battery performance data. The charger is suitable for most lead-acid battery types including calcium, gel and AGM batteries. In addition, the charger has a "reconditioning function", which makes so-called deeply discharged batteries fit for everyday use again by eliminating acid stratification and sulphation. Technical features of the charger: The charger has all modern functions such as: Soft start overvoltage protection Reconditioning Suitable for calcium, wet, AGM, fleece, VRLA and gel batteries Integrated automatically controlled fans Minimum starting voltage of only 2V Reverse polarity protection Overload protection Overheating protection Efficiency >85% The 7 stages at a glance: DESULPHATION (desulphation): Gently increasing and decreasing voltages and currents at the beginning of the charging process eliminate battery sulphation caused by short-distance driving and frequently discharged batteries. SOFTSTART (soft start): Regulated gently increasing voltages ensure a gentle transition and start to the main charge and prevent damage to the lead grids. BULK (main charge): The battery is charged at a steady current and carefully increasing voltage up to a predefined maximum voltage value until 80% of the total charge has been reached. ABSORPTION (residual charge): The battery is fully charged to 100% of the total charge by maintaining a constant voltage and gradually decreasing currents. The gradually decreasing current ensures that the terminal voltage does not become too high during full charging. BATTERY TEST: The battery is tested for self-discharge for 90 seconds. If the absorption phase has not been able to fully charge the battery and the voltage drop is therefore too high, which is the case with old batteries or batteries with strong acid stratification, for example, the system automatically switches to reconditioning mode RECONDITION (reconditioning): This mode starts with very low currents but high voltages of up to 32V, which remedies the acid stratification in deeply discharged batteries. This mode is limited to a maximum of 4 hours and improves battery life and performance. FLOAT/MAINTENANCE (charge retention/maintenance charge): The battery is evenly maintained at 27.6V "float" voltage without overcharging the battery or damaging you. This means that the charger can also remain connected all year round (e.g. for seasonal vehicles/oldtimers) The voltage in this mode is permanently monitored. As soon as the battery voltage falls to a predefined level, the battery is recharged to 100% by a pulse charge and thus constantly maintained between 95% and 100% state of charge. This cycle is repeated automatically and thus has a positive effect on the battery's service life. High-quality and durable workmanshipWith the Paco MBC charger, particular attention has been paid to a functional and durable external and internal design. For example, the housing is made of high-strength aluminum and is therefore robust and resistant to external influences, while the LED panel on the side of the device means you can always see which mode the charger is currently in.The solid battery terminals and plugs, which have a sufficient cable cross-section, are also of very good and durable quality.Scope of delivery: Paco MBC charger Detailed instructions for use, version: German/English

Votronic battery charger VAC-2440 M 2A Built-in mains chargers for emergency vehicles and demanding motorhome and camper owners. Especially for rescue and emergency vehicles, the reliability of the batteries installed in the vehicle is crucial for the operational readiness of the vehicle. This is particularly the case when the batteries are subject to heavy loads from many continuous consumers, when there is not enough time to recharge them due to frequent use or when the charger is inadequately adapted to the batteries. In order to meet the special requirements of emergency vehicles, the VAC series was created in cooperation with vehicle and leading battery manufacturers.Votronic charging technology has been used for years in professional emergency vehicles such as fire engines, ambulances and coastguards! Quality - Made in Germany! The device electronics are protected against moisture and ensure safe operation in the event of severe temperature fluctuations. Continuous consumers connected to the vehicle electrical system (radios, charging trays etc.) are also supplied without impairing the charging process. The built-in charging current distributor also automatically supplies the starter battery with full charging current if required. The engine start lock can be activated via a signal output when the vehicle is connected to the mains.The devices are supplied with an 825 temperature sensor to ensure optimum charging of the batteries. The installation position is variable, thanks to a second device label included in the scope of delivery. Instead of a remote control, a waterproof LED display (see accessories) can be connected to the Remote Control connection socket, which indicates the operational readiness of the device on the outside of the vehicle.Further special features at a glance: Votronic products "Made in Germany" High charging power even for short journeys Significantly improved energy balance of the on-board battery Optimum charging characteristics for all battery types can be set using the battery selector switch (lead-acid, gel, AGM, lithium LiFePO4) Suitable for all alternators Automatic, adjustable power control ensures priority charging of the starter battery by the alternator when the vehicle electrical system is under heavy load, thus ensuring that the vehicle can be started again immediately Simple installation, no intervention in the vehicle's starter circuit required, device is connected in the charging line to the supply battery Parallel operation to increase power possible Particularly recommended for vehicles with Euro 6 standard Temperature sensor 825 already included in the scope of delivery The charging converters are also characterized by their compact design, low weight (high-frequency switching transformer, switch mode technology) and powerfully dimensioned power components. 6 operating displays provide information about the operating status of the device at all times. Recommended accessories: Votronic remote control S (2075) and remote operating display IP67 (2081)

PACO MEC2405 5A/24V battery charger